• 대한전자공학회논문지SD
• /
• 제39권10호
• /
• pp.25-34
• /
• 2002

본 논문에서는 코발트 실리사이드가 형성된 얕은 p+-n과 n+-p 접합의 전류-전압 특성을 분석하여 silicidation에 의해 형성된 Schottky contact 면적을 구하였다. 역방향 바이어스 영역에서는 Poole-Frenkel barrier lowering 효과가 지배적으로 나타나서 Schottky contact 효과를 파악하기가 어려웠다. 그러나 Schottky contact의 형성은 순방향 바이어스 영역에서 n+-p 접합의 전류-전압 (I-V) 동작에 영향을 미치는 것으로 확인되었다. 실리사이드가 형성된 n+-p 다이오드의 누설전류 증가는 실리사이드가 형성될 때 p-substrate또는 depletion area로 코발트가 침투퇴어 Schottky contact을 형성하거나 trap들을 발생시켰기 때문이다. 분석결과 perimeter intensive diode인 경우에는 silicide가 junction area까지 침투하였으며, area intensive junction인 경우에는 silicide가 비록 공핍층이나 p-substrate까지 침투하지는 않았더라도 공핍층 근처까지 침투하여 trap들을 발생시켜 누설전류를 증가시킴을 확인하였다. 반면 p+-n 다이오드의 경우 Schottky contact이발생하지 않았고 따라서 누설전류도 증가하지 않았다. n+-p 다이오드에서 실리사이드에 의해 형성된 Schottky contact 면적은 순방향 바이어스와 역방향 바이어스의 전류 전압특성을 동시에 제시하여 유도할 수 있었고 전체 접합면적의 0.01%보다 작게 분석되었다.

• 한국재료학회지
• /
• 제24권3호
• /
• pp.135-139
• /
• 2014

To obtain the transistor with ambipolar transfer characteristics, IGZO/SiOC thin film transistor was prepared on SiOC with various polarities as a gate insulator. The interface between a channel and insulator showed the Ohmic and Schottky contacts in the bias field of -5V ~ +5V. These contact characteristics depended on the polarities of SiOC gate insulators. The transfer characteristics of TFTs were observed the Ohmic contact on SiOC with polarity, but Schottky contact on SiOC with low polarity. The IGZO/SiOC thin film transistor with a Schottky contact in a short range bias electric field exhibited ambipolar transfer characteristics, but that with Ohmic contact in a short range electric field showed unipolar characteristics by the trapping phenomenon due to the trapped ionized defect formation.

• E2M - 전기 전자와 첨단 소재
• /
• 제8권1호
• /
• pp.56-63
• /
• 1995

MESFETs of the Ti/Au and Ti/Pd/Au gate were fabricated on n-type GaAs. Interdiffusion at Schottky interfaces, Schottky contact properties, and MESFET characteristics with heat treatment were investigated. Ti of Ti/Au contact and Pd of Ti/Pd/Au contact acted as a barrier metal against interdiffusion of Au at >$220^{\circ}C$. Pd of Ti/Pd/Au contact acted as a barrier metal even at >$360^{\circ}C$, however, Ti of Ti/Au contact promoted interdiffusion of Au instead of role of barrier metal. As the heat treatment temperature increases, in the case of both contact, saturated drain current and pinch off voltage decreased, open channel resistance increased, and degree of parameter variation in Ti/Au gate was higher than in Ti/Pd/Au gate at >$360^{\circ}C$ Schottky barrier height of Ti/Au and Ti/Pd/Au contacts was 0.69eV and 0.68eV in the as-deposited state, respectively, and Fermi level was pinned in the vicinity of 1/2Eg. As the heat treatment temperature increases, barrier height of Ti/Pd/Au contact increased, however, decreased at >$360^{\circ}C$ in the case of Ti/Au contact. Ideality factor of Ti/Au contact was nearly constant regardless of heat treatment, however, increased at >$360^{\circ}C$ in the case of Ti/Au contact. From the results above, Ti/Pd/Au was stable gate metal than Ti/Au.

• 전기학회논문지
• /
• 제60권12호
• /
• pp.2265-2269
• /
• 2011

1 kV high-voltage GaN Schottky diode is realized using GaN-on-Si template by oxidizing Ni-Schottky contact. The Auger electron spectroscopy (AES) analysis revealed the formation of $NiO_x$ at the top of Schottky contact. The Schottky contact was changed to from Ni/Au to Ni/Ni-Au alloy/Au/$NiO_x$ by oxidation. Ni diffusion into AlGaN improves the Schottky interface and the trap-assisted tunneling current. In addition, the reverse leakage current and the isolation-leakage current are efficiently suppressed by oxidation. The isolation-leakage current was reduced about 3 orders of magnitudes. The reverse leakage current was also decreased from 2.44 A/$cm^2$ to 8.90 mA/$cm^2$ under -100 V-biased condition. The formed group-III oxides ($AlO_x$ and $GaO_x$) during the oxidation is thought to suppress the surface leakage current by passivating surface dangling bonds, N-vacancies and process damages.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2010년도 하계학술대회 논문집
• /
• pp.390-390
• /
• 2010

We fabricate Schottky diodes with the contact between a sol-gel derived ZnO layer and Au that guarantees the expected Schottky contact due to the high work function. The formed single metal Schottky barrier shows characteristics comparable to the barrier formed by alloys. Au is deposited by thermal evaporation on a ZnO thin film that is optimally formed under sol-gel process conditions of a 1-mol zinc acetate concentration and a 3000-rpm coating speed. Possible defects. which can provide deleterious current paths. are minimized by patterning the deposited Au. The I-V curve verifies the formation of a Schottky contact. Measurements showed that the Schottky barrier height and leakage current at -5 V were 0.6 eV and $1{\times}10^{-12}A$. respectively.

• 한국산학기술학회논문지
• /
• 제19권6호
• /
• pp.709-714
• /
• 2018

반도체소자의 접합특성에 따라서 분극의 특성이 달라지는 원인을 조사하였다. 반도체소자의 접합특성은 최종적인 반도체소자의 효율과 관련되기 때문에 중요한 요소이며, 효율을 높이기 위해서는 반도체접합 특성을 이해하는 것은 매우 중요하다. 다양한 성질의 접합을 얻기위하여 n형의 실리콘 위에 절연물질인 carbon doped silicon oxide (SiOC) 박막을 증착하였으며, 아르곤 (Ar) 유량에 따라서 반도체기판의 특성이 달라지는 것을 확인하였다. 전도체인 tin doped zinc oxide (ZTO) 박막을 절연체인 SiOC 위에 증착하여 소자의 전도성을 살펴보았다. SiOC 박막의 특성은 플라즈마에 의하여 이온화현상이 일어날 때 Ar 유량에 따라서 이온화되는 경향이 달라지면서 반도체 계면에서의 공핍현상이 달라졌으며, 공핍층 형성이 많이 일어나는 곳에서 쇼키접합 특성이 잘 형성되는 것을 확인하였다. 아르곤 가스의 유량이 많은 경우 이온화 반응이 많이 일어나고 따라서 접합면에서 전자 홀쌍의 재결합반응에 의하여 전하들이 없어지게 되면 절연특성이 좋아지고 공핍층의 전위장벽이 증가되며, 쇼키접합의 형성이 유리해졌다. 쇼키접합이 잘 이루어지는 SiOC 박막에서 ZTO를 증착하였을 때 SiOC와 ZTO 사이의 계면에서 전하들이 재결합되면서 전기적으로 안정된 ZTO 박막을 형성하고, ZTO의 전도성이 증가되었다. 두께가 얇은 반도체소자에서 흐르는 낮은 전류를 감지하기 위해서는 쇼키접합이 이루어져야 하며, 낮은 전류만으로도 전기신호의 품질이 우수해지고 또한 채널층인 ZTO 박막에서의 전류의 발생도 많아지는 것을 확인하였다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2015년도 제49회 하계 정기학술대회 초록집
• /
• pp.209.2-209.2
• /
• 2015

Two dimensional layered materials, such as transition metal dichalcogenides (TMDs) family have been attracted significant attention due to novel physical and chemical properties. Among them, molybdenum disulfide ($MoS_2$) has novel physical phenomena such as absence of dangling bonds, lack of inversion symmetry, valley degrees of freedom. Previous studies have shown that the interface of metal/$MoS_2$ contacts significantly affects device performance due to presence of a scalable Schottky barrier height at their interface, resulting voltage drops and restricting carrier injection. In this study, we report a new device structure by using few-layer graphene as the bottom interconnections, in order to offer Schottky barrier free contact to bi-layer $MoS_2$. The fabrication of process start with mechanically exfoliates bulk graphite that served as the source/drain electrodes. The semiconducting $MoS_2$ flake was deposited onto a $SiO_2$ (280 nm-thick)/Si substrate in which graphene electrodes were pre-deposited. To evaluate the barrier height of contact, we employed thermionic-emission theory to describe our experimental findings. We demonstrate that, the Schottky barrier height dramatically decreases from 300 to 0 meV as function of gate voltages, and further becomes negative values. Our findings suggested that, few-layer graphene could be able to realize ohmic contact and to provide new opportunities in ohmic formations.

• Transactions on Electrical and Electronic Materials
• /
• 제18권4호
• /
• pp.225-228
• /
• 2017

In this study, zinc tin oxide (ZTO) films were prepared on indium tin oxide (ITO) glasses and annealed at different temperatures under vacuum to investigate the correlation between the Ohmic/Schottky contacts, electrical properties, and bonding structures with respect to the annealing temperatures. The ZTO film annealed at $150^{\circ}C$ exhibited an amorphous structure because of the electron-hole recombination effect, and the current of the ZTO film annealed at $150^{\circ}C$ was less than that of the other films because of the potential barrier effect at the Schottky contact. The drift current as charge carriers was similar to the leakage current in a transparent thin-film device, but the diffusion current related to the Schottky barrier leads to the decrease in the leakage current. The direction of the diffusion current was opposite to that of the drift current resulting in a two-fold enhancement of the cut-off effect of leakage drift current due to the diffusion current, and improved performance of the device with the Schottky barrier. Hence, the thin film with an amorphous structure easily becomes a Schottky contact.

• Journal of information and communication convergence engineering
• /
• 제16권4호
• /
• pp.248-251
• /
• 2018

To research the characteristics of $TiO_2$ as an insulator, $TiO_2$ films were prepared with various annealing temperatures. It was researched the currents of $TiO_2$ films with Schottky barriers in accordance with the contact's properties. The potential barrier depends on the Schottky barrier and the current decreases with increasing the potential barrier of $TiO_2$ thin film. The current of $TiO_2$ film annealed at $110^{\circ}C$ was the lowest and the carrier density was decreased and the resistivity was increased with increasing the hall mobility. The Schottky contact is an important factor to become semiconductor device, the potential barrier is proportional to the hall mobility, and the hall mobility increased with increasing the potential barrier and became more insulator properties. The reason of having the high mobility in the thin films in spite of the lowest carrier concentration is that the conduction mechanism in the thin films is due to the band-to-band tunneling phenomenon of electrons.

• 반도체디스플레이기술학회지
• /
• 제17권4호
• /
• pp.66-69
• /
• 2018

This study was researched the electrical properties of semiconductor devices such as ITO, $SiO_2$, $V_2O_5$ thin films. The films of ITO, $SiO_2$, $V_2O_5$ were deposited by the rf magnetron sputtering system with mixed gases of oxygen and argon to generate the plasma. All samples were cleaned before deposition and prepared the metal electrodes to research the current-voltage properties. The electrical characteristics of semiconductors depends on the interface's properties at the junction. There are two kinds of junctions such as ohmic and schottky contacts in the semiconductors. In this study, the ITO thin film was shown the ohmic contact properties as the linear current-voltage curves, and the electrical characteristics of $SiO_2$ and $V_2O_5$ films were shown the non-linear current-voltage curves as the schottky contacts. It was confirmed that the electronic system with schottky contacts enhanced the electronic flow owing to the increment of efficiency and increased the conductivity. The schottky contact was only defined special characteristics at the semiconductor and the interface depletion layer at the junction made the schottky contact which has the effect of leakage current cutoff. Consequently the semiconductor device with shottky contact increased the electronic current flow, in spite of depletion of carriers.