• Journal of Sensor Science and Technology
• /
• v.19 no.3
• /
• pp.230-237
• /
• 2010

In sensor signal conditioning and processing, offset and drift characteristics of an operational amplifier are an important factor when the amplifier is used for a precise sensor signal amplifier. In order to use it in high accuracy, an expensive trimming or a complex compensation circuit is required. This paper presents the improved sensor signal conditioning and processing device for ubiquitous sensor network(USN) application or general purpose by developing a hardware of the circuit for reducing the offset voltage and drift characteristics, and a software for its control and sensor signal processing. We realize better offset voltage and drift characteristics of the signal conditioning circuit using low cost operational amplifiers. The experimental results show that this technique is effective in improving the performance of the sensor signal processing device.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.14 no.5
• /
• pp.28-35
• /
• 2015

This paper introduces a resistance scanning-type flexible tactile sensor for intelligent robots and presents the output characteristics of the sensor via signal processing. The sensor was produced via the lamination method using multi-walled carbon nanotubes (a conductive material), an insulator, and Tango-plus (an elastic material). Analog and digital signal processing boards were produced to analyze the output signal of the sensor. The analog signal processing board was made up of an integrator and an amplifier for signal stability, and the digital signal processing board was made up of an IIR filter for noise removal. Finally, the sensor output for the contact force was confirmed through experiments.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.28 no.12
• /
• pp.84-89
• /
• 2014

This paper proposes the new multiple signal processing monitoring sensor for the marine installation. The recent marine technology is focused on underwater sensors and underwater sensor networks in order to measure, monitor, surveillance of and control of underwater environments. For these marine applications to be available, however, the provision of precise location information using monitoring sensor is essential. In this paper, the multiple signal processing circuit for obtaining the precise location information of marine installation sensor is developed and analyzed. The performance characteristics for obtaining the location information of marine installation sensor is analyzed. The theoretical and experimental studies have been carried out. The presented results from the above investigation show considerably excellent performance for the monitoring for the marine installation.

• 제어로봇시스템학회:학술대회논문집
• /
• 2005.06a
• /
• pp.1999-2005
• /
• 2005

Collaboration in wireless sensor networks must be fault-tolerant due to the harsh environmental conditions in which such networks can be deployed. This paper focuses on finding signal processing algorithms for collaborative target detection based on the generalized approach to signal processing in the presence of noise that are efficient in terms of communication cost, precision, accuracy, and number of faulty sensors tolerable in the wireless sensor network. Two algorithms, namely, value fusion and decision fusion constructed according to the generalized approach to signal processing in the presence of noise, are identified first. When comparing their performance and communication overhead, decision fusion is found to become superior to value fusion as the ratio of faulty sensors to fault free sensors increases. The use of the generalized approach to signal processing in the presence of noise under designing value and decision fusion algorithms in wireless sensor networks allows us to obtain the same performance, but at low values of signal energy, as under the employment of universally adopted signal processing algorithms widely used in practice.

• Journal of Welding and Joining
• /
• v.13 no.4
• /
• pp.65-74
• /
• 1995

The weld seam tracking sensor is indispensable to improve the flexibility of automatic arc welding systems. Among the position sensing methods available, a laser displacement sensor is one of the most prevailing methods. In this study, a laser displacement sensor was examined on detecting the weld seam of lap joints in sheet metal arc welding. The output signal of the laser displacement sensor may ontain severe fluctuation from the effect of arc light, spatters, fume, etc. So a variety of signal processing methods was applied to smooth the output signal of the sensor. And then the weld joint was determined by using the central difference method. It was revealed that the quadratic mean method plays an important role in detecting the weld seam during welding especially.

• Journal of Sensor Science and Technology
• /
• v.20 no.2
• /
• pp.107-113
• /
• 2011

LSPR(Localized Surface Plasmon Resonance) sensor measures the refractive index change on the sensor surface. The detection of biological reaction with the unknown refractive index needs to be converted into the signal sensitivity for the refractive index change for comparison with other measurements. To find the signal sensitivity, the three steps of signal processing are proposed, which are signal modeling, signal calibration and signal normalization of LSPR sensor. The detected signal of biotin-streptavidin interaction has been converted into unit of [RU](Resonance Unit) using the proposed method. The converted signal directly can be compared with the other sensors including commercialized one.

• 제어로봇시스템학회:학술대회논문집
• /
• 2003.10a
• /
• pp.942-947
• /
• 2003

An important signal processing problem in PVDF sensor is the restoration of surface information from electric sensing signals. The objectives of this research are to design a new texture sensing system and to develop a new signal processing algorithm for signals from the sensor to be tangibly displayed by tangible interface systems. The texture sensing system is designed to get surface information with high resolution and dynamic range. First, a PVDF sensor is made of piezoelectric polymer (polyvinylidene fluoride) strips molded in a silicon rubber and attached in a rigid cylinder body. The sensor is mounted to a scanning system for dynamic sensing. Secondly, a new signal processing algorithm is developed to restore surface information. The algorithm consists of the two-dimensional modeling of the sensor using an identification method and inverse filtering from sensing signals into estimated surface information. Finally the two-dimensional surface information can be experimentally reconstructed from sensing signals using the developed signal processing algorithm.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.11 no.4
• /
• pp.1272-1277
• /
• 2010

Target detection and tracking wireless sensor network must have various signal processing ability. Wireless sensor nodes need to light weight signal processing algorithm because of energy constraints and communication bandwidth constraints. General signal processing algorithm of wireless sensor node consists of de-noising, received signal strength computation, feature extraction and signal compression. Wireless sensor network life-time and performance of target detection and classification depend on sensor node signal processing. In this paper, we propose energy efficient signal processing algorithm using wavelet transform. The proposed method estimates exact target position.

• Journal of Institute of Control, Robotics and Systems
• /
• v.7 no.2
• /
• pp.146-151
• /
• 2001

The importance of sensing the force and torque with arbitrary direction and magnitude is becoming more crucial for robotic applications and manufacturing automations. Recently, several designs of a multi-axis force-torque sensor have been tried to sense this force and torque. This paper deals mainly with the signal processing of a six-axis force-torque sensor using cross-shaped elastic structures with circular holes. In this paper, we show principle of sensing force and torque, the signal processing methodology, and efficient methods of seeking strain gage positions in the sensor structure. The validity of the proposed method is shown via experiments.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.20 no.9
• /
• pp.103-109
• /
• 2006

This research is contents about output characteristic of optic current sensor that use faraday effect. optic current sensor used in an experiment is consisted of three parts.(1) Source of light used laser diode of 1310[nm].(2) Sensor section manufactured circularly according to gas insulated switchgear. And $9/125[{\mu}m]$ standard single mode optical fiber for communication was installed winding 20 [turn] on sensor section core surroundings of diameter 31 [cm].(3) Electrical signal of PD(Photo detector) is collected using NI company's 16bit DAQ board via terminal block. Collected data analyzed by different three signal processing methods. NI company's $Labview^{TM}$ was used to signal processing software. As a result, In signal processing of optic current sensor, we could know that noise greatly more influences the error generation than fluctuation of light intensity. also, 1 class CT(current transformer) manufacture that have error rate less than 1[%] was available by removing these