• Magazine of the Korean Society of Agricultural Engineers
• /
• v.28 no.4
• /
• pp.49-56
• /
• 1986

This study was carried out to investigate mechanical characteristics of the uniformly loaded skew-plate at 4 kinds of boundary condition : i) all edges are clamped (BC-1) , ii) all edges are simply supported (BC- 2), iii) two opposite edges are clamped and the other two edges are free (BC-3), and iv )two opposite edges are simply supported and the other two edges are free (BC-4). Various skew angles, 0$^{\circ}$, 10$^{\circ}$, 15$^{\circ}$, 30$^{\circ}$, 40: 45: and 60, of the plate were tested for the above boundary conditions. Resutts obtained from the study are summarized as follows ; 1.The lateral displacement at the center of a skew- plate was decreased as the skewangle increased at all of the boundary conditions. The decrements of the conditions of BC-3 and BC-4 were considerable. And, difference of the displacement between the boundary conditions was decreased as the skew-angle was increased. 2. X-moments (to the Y-axis) at the center of a skew- plate and the minimum principal moments were shown as a similar pattern of change with respect to the skew-angle variation between BC-i and BC-2 and between BC-3 and BC-4, and the pattern of change at the conditions of BC-3 and BC-4 were shown higher rates than those for the conditions of BC-i and BC-2 3.Y-moments (to the X- axis) at the center of a skew-plate and the maximum principal moment were decreased as the skew-angle increased in a similar pattern at all of the boundary conditions. 4.X-moments at the obtuse angle side of a skew-plate were shown as a parabolic pattern of change (frist increased after then decreased) as the skew-angle increased, and a skew-angle resulting the maximum absolute moment was depended on the boundary conditions. 5.Y-moments at the obtuse angle side of a skew-plate were affected by the skewangle much more at the boundary condtions of BC-2 and BC-4 than at the conditions of BC-i and BC-3. 6.Maximum principal moments at the obtuse angle side of a skew-plate at the skew angle of 40$^{\circ}$- 45$^{\circ}$ were resulted almost the same value at all of the boundary conditions .

• Steel and Composite Structures
• /
• v.11 no.5
• /
• pp.359-374
• /
• 2011

In this paper, the influence of fibre orientation and aspect ratio on stability analysis of simply supported skew plates subjected to in plane loading is studied by using a four noded hybrid plate finite element. The formulation of the element is based on Hellinger-Reissner variational principle. The element is developed by combining a hybrid plane stress element and a hybrid plate element. Some numerical problems are solved and the effects of skew angle, aspect ratio, fibre orientation and loading type on the critical buckling loads are highlighted.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.15 no.1
• /
• pp.169-178
• /
• 1991

A plane-strain finite element analysis of sheet metal forming is carried out by using the rigid-plastic FEM based on the membrane theory. The sheet material is assumed to possess normal anisotropy and to obey Hill's new yield criterion and its associated flow rule. A formulation of initial guess generation for the displacement field is derived by using the nonlinear elastic FEM. A method of contact treatment is proposed in which the skew boundary condition for arbitrarily shaped tools is successively used during iteration. In order to verify the validity of the developed method, plane-strain drawing with tools in analytic expression and with arbitrarily shaped tools is analyzed and compared with the published results. The comparison shows that the present method can be effectively used in the analysis of plane-strain sheet metal forming and thus provides the basis of approximate sectional analysis of panel-like sheet forming.

• Structural Engineering and Mechanics
• /
• v.74 no.2
• /
• pp.227-241
• /
• 2020

The bi-axial and shear buckling behavior of laminated hypar shells having rhombic planforms are studied for various boundary conditions using the present mathematical model. In the present mathematical model, the variation of transverse shear stresses is represented by a second-order function across the thickness and the cross curvature effect in hypar shells is also included via strain relations. The transverse shear stresses free condition at the shell top and bottom surfaces are also satisfied. In this mathematical model having a realistic second-order distribution of transverse shear strains across the thickness of the shell requires unknown parameters only at the reference plane. For generality in the present analysis, nine nodes curved isoparametric element is used. So far, there exists no solution for the bi-axial and shear buckling problem of laminated composite rhombic (skew) hypar shells. As no result is available for the present problem, the present model is compared with suitable published results (experimental, FEM, analytical and 3D elasticity) and then it is extended to analyze bi-axial and shear buckling of laminated composite rhombic hypar shells. A C⁰ finite element (FE) coding in FORTRAN is developed to generate many new results for different boundary conditions, skew angles, lamination schemes, etc. It is seen that the dimensionless buckling load of rhombic hypar increases with an increase in c/a ratio (curvature). Between symmetric and anti-symmetric laminations, the symmetric laminates have a relatively higher value of dimensionless buckling load. The dimensionless buckling load of the hypar shell increases with an increase in skew angle.

• 유체기계공업학회:학술대회논문집
• /
• 2005.12a
• /
• pp.525-532
• /
• 2005

Shape optimization of a transonic axial compressor rotor operating at the design flow condition has been performed using response surface method and three-dimensional Navier-Stokes analysis. Three design variables of blade sweep. lean and skew are introduced to optimize the three-dimensional stacking line of the rotor blade. The object function of the shape optimization is selected as an adiabatic efficiency. Throughout the shape optimization of the rotor. the adiabatic efficiency is increased by reducing the tub comer and tip losses. Separation line due to the interference between a passage shock and surface boundary layer on the blade suction surface is moved downstream for the optimized blade compared to the reference one.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.13 no.6
• /
• pp.1092-1103
• /
• 1989

본 논문에서는 기존의 금속성형의 유한요소해석에서 사용한 바 있는 기하적경 계조건을 직접 유한요소방정식에 대입하는 방법들을 비교검토하고 3차원박판성형에 적용하기 위하여 개선된 방법을 개발하였다.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.28 no.12
• /
• pp.1950-1957
• /
• 2004

Analysis for structures composed of materials containing regularly spaced in-homogeneities is usually executed by using averaged material properties. In order to evaluate the effective properties, a unit cell is defined and loaded somehow, and its response is investigated. The imposed loading, however, should accord to the status of unit cells immersed in the macroscopic structure to secure the accuracy of the properties. In this study, mathematical description for the periodicity of the displacement field is derived and its direct implementation into FE models of unit cell is attempted. Conventional finite element code needs no modification, and only the boundary of unit cell should be constrained in a way that the periodicity is preserved. The proposed method is applicable to skew arrayed in-homogeneity problems. Homogenized in-plane elastic properties are evaluated for a few representative cases and the accuracy is examined.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.22 no.2
• /
• pp.380-390
• /
• 1998

In the present work a finite element formulation using dynamic explicit time integration scheme is used for numerical analysis of auto-body panel stamping processes. The lumping scheme is employed for the diagonal mass matrix and linearizing dynamic formulation. A contact scheme is developed by combining the skew boundary condition and direct trial-and-error method. In this work, for economic analysis the faster punch velocity and the mass scaling method are introduced. To investigate the effects of punch velocity and mass scaling, the various values of punch velocity and the various mass scalings are used for numerical analysis. Computations are carried out for analysis of complicated auto-body panel stamping processes such as forming of an oil pan and a fuel tank.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1994.10a
• /
• pp.55-63
• /
• 1994

The analysis of superplastic sheet forming process is studied by the use of the finite element method using a convected coordinate system and a skew boundary condition. In the formulation, the large inelastic behavior of the superplastic material is described as incompressible, nonlinear, viscous flow. The formulation is then approximated to the finite dimensional space with the use of membrane elements, which results in algebraic linear equations. In addition to the finite element formulation, a pressure cycle control algorithm is combined in the analysis for optimization of the forming time, which deals with the maximization of the strain rate sensitivity, the protection of the thickness reduction, the consistency of the desired strain rate and improvement of formability.

• Journal of the Korean Society for Precision Engineering
• /
• v.14 no.9
• /
• pp.101-107
• /
• 1997

A sectional analysis of auto-body panel stamping is carried out by using the rigid-plastic FEM based on the membrane theory. The auto-body panel material is assumed to possess normal anisotropy and to obey Hill's new yield criterion and its associated flow rule. A method of contact treatment is proposed in which the skew boundary condition for arbitarily shaped tools is successively used during iteration. Deformation of each section of trunk-lid panel is simulated and composed to get the three-dimensional shape by using CAD technique. It was shown that the composition of the two-dimensional section analysis gives almost the same results as the full three-dimensional analysis.