• Proceedings of the IEEK Conference
• /
• 2000.11a
• /
• pp.357-360
• /
• 2000

This paper describes a parameter extraction method for HBT(Heterojunction Bipolar Transistor) equivalent circuit model without measurements of special test structures or numerical optimizations. Instead, all equivalent circuit parameters are calculated analytically from small-signal S-parameters measured under different bias conditions. These values being extracted from the cutoff mode can be used to extract intrinsic parameters at the active mode. This method yields a deviation of about 1.3 % between the measured and modeled S-parameters.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.33A no.6
• /
• pp.164-171
• /
• 1996

We report the experimental resutls on AlGaAs/GaAs heterojunction bipolar transistors (HBTs) with carbon-doped base structure. To characterize the output power, load-pull mehtod was employed. By characterizing the devices with HP8510C, we extracted the small-signal equivalent circuit. The HBTs were fabricated employing wet mesa etching and lift-off process of ohmic metals. the implementation of polyimide into the fabriction process was accomplished to obtain the lower dielectric constant resultig in significant reduction of interconnect routing capacitance. The fabricated HBTs with an emitter area of 6${\times}14{\mu}m^{2}$ exhibited current gain of 45, BV$_{CEO}$ of 10V, cut-off frequency of 30GHz and power gain of 1 3dBm. To extract the small signal equivalent circuit, the de-embedded method was applied for parasitic parameters and the calculation of circuit equations for intrinsic parameters.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.12
• /
• pp.7287-7291
• /
• 2014

A CDTA (current differencing transconductance amplifier) is an active building block for current mode analog signal processing with the advantages of high linearity and a wide frequency bandwidth. In addition, it can generate a stable voltage because all the differencing input current flows to the grounded devices. In this paper, a new small signal equivalent circuit is proposed to analyze a CDTA. The proposed small signal equivalent circuit provides greater precision in analyzing the magnitude and frequency response than its previous counterparts because it considers the parasitic components of the input, internal and output terminal. In addition, observations of the changes made in various devices, such as the resistor (Rz) confirmed that those devices heavily influence the characteristics of CDTA. The designed parameters of the proposed small signal equivalent circuit of the CDTA provides convenience and accuracy in the further design of analog integrated circuits. For verification purposes, a 2.5 MHz low pass filter was designed on the HSPICE simulation program using the proposed small signal equivalent circuit of CDTA.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.12 no.4
• /
• pp.377-387
• /
• 2012

An intrinsic small signal equivalent circuit model of Cylindrical/Surrounded gate MOSFET is proposed. Admittance parameters of the device are extracted from circuit analysis and intrinsic circuit elements are presented in terms of real and imaginary parts of the admittance parameters. S parameters are then evaluated and justified with the simulated data extracted from 3D device simulation.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.33A no.7
• /
• pp.156-161
• /
• 1996

Accurate equivalent circuit modeling using multi-circuit optimization has been perfomred for detemining small-signal model of AlGaAs/GaAs HBTs. Three equivalent circuits for a cutoff biasing and two active biasing at different curretns are optimized simultaneously to fit gheir S parameters under the physics-based constrain that current-dependent elements for one of active circuits are connected to those for another circit multiplied by the ratio of two currents. The cutoff mode circuit and the physical constrain give the advantage of extracting physically acceptable parameters, because the number of unknown variables. After this optimization, three ses of optimized model S-parameters agree well with their measured S-parameters from 0.045 GHz to 26.5GHz.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.7 no.4
• /
• pp.743-749
• /
• 2003

By biasing the gate of cold-HEMT with a voltage slightly lower than the pinch-off point, a new small-signal modeling method that is free from gate degradation problem and requires no additional DC measurement is proposed in this paper. The method has shown excellent agreement between modeled and measured S-parameters up to 62 GHz at 49 different normal operating bias points.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.10 no.2
• /
• pp.169-176
• /
• 2005

In this paper, a DC and small-signal AC modeling for the active-clamp, ful1-bridge boost converter is described. Based on the operation principle, the ac part of the converter can be replaced by a dc counterpart. Then, a conceptual equivalent circuit is derived by rearranging the switches. The equivalent circuit for this converter consists of CCM(Continuous conduction mode) boost and DCM(Discontinuous conduction mode) buck converter. The analyses for the equivalent CCM boost and DCM buck converter are done using the model of PWM switch. The theoretical modeling results are confirmed through experiment or SIMPLIS simulation.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.11 no.10
• /
• pp.1910-1915
• /
• 2007

An accurate and simple method to extract equivalent circuit parameters of fully-depleted silicon-on-insulator MOSFETs small-signal modeling operating at RF frequencies including the non-quasi static effects is presented in this article. The advantage of this method is that a unique and physically meaningful set of intrinsic equivalent circuit parameters is extracted by de-embedding procedure of extrinsic elements such as parasitic capacitances and resistances of MOSFETs from measured S-parameters using simple Z- and Y- matrices calculations. The calculated small-signal parameters using the presented extraction method give modeled Y-parameters which are in good agreement with the measured Y-parameters from 0.5 to 20GHz.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.14 no.6
• /
• pp.768-776
• /
• 2014

Using a simplified high-frequency small-signal equivalent circuit model for BSIM3 MOSFET, the fully differential two-stage folded-cascode CMOS operational amplifier is analyzed to obtain its small-signal voltage transfer function. As a result, the expressions for dc gain, five zero frequencies, five pole frequencies, unity-gain frequency, and phase margin are derived for op amp design using design equations. Then the analysis result is verified through the comparison with Spice simulations of both a high speed op amp and a low power op amp designed for the $0.13{\mu}m$ CMOS process.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.41 no.12
• /
• pp.21-26
• /
• 2004

In this paper, a direct method is developed to extact RF equivalent circuit of a packaged BJT without optimization. First, parasitic components of plastic package are removed from measured S-parameters using open and short package patterns. Using package do-embedded S-parameters, a direct and simple method is proposed to extract bonding wire inductance and chip pad capacitance between package lead and chip pad. The small-signal model parameters of internal BJT are next determined by Z and Y-parameter formula derived from RF equivalent circuit. The modeled S-parameters of packaged BJT agree well with measured ones, verifying the accuracy of this new extraction method.