• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.54 no.12
• /
• pp.573-577
• /
• 2005

[$TiO_2$] sol and $SiO_2$ sol were prepared using sol-gel method. As $H_{2}O$/Alkoxide ratios increased, sol had cluster structure and as $H_{2}O$/Alkoxide ratios decreased, sol had linear structure. Gelation time of $TiO_2$ sol was faster than that of $SiO_2$ sol according to the time. In comparison with initial viscosity between $TiO_2$ sol and $SiO_2$ sol, $TiO_2$ sol was highest at $H_{2}O/Ti(OC_{3}H_{7})_{4}=5$, $SiO_2$ sol was almost constant according to $H_{2}O/Si(OC_{2}H_{5})_{4}$ ratios.

• Proceedings of the KIEE Conference
• /
• 2002.11a
• /
• pp.91-93
• /
• 2002

Ti-Sn sol is fabricated using sol-gel method. In case the amount of water required hydrolysis smaller than that for stoichiometry, Ti sol forms clear sol which has normal chain structure. On the contrary, in case the amount of water required hydrolysis larger than that for stoichiometry, Ti sol forms suspended sol which has cluster structure. Viscosity of Ti-Sn sol decrease with increasing HCl additive. Gelation of Ti-Sn sol is delayed with increasing HCl and $Sn(OC_2H_5)_4$ additive.

• Journal of Technologic Dentistry
• /
• v.29 no.1
• /
• pp.121-131
• /
• 2007

A preparation process's conditions of aqueous sol which contains anatase-type nano titania particles with photocatalyic properties was established by using Yoldas process, so called, DCS(Destabilization of Colloidal Solution) process in this study. And crystal size change and phase transformation of titania particles in aqueous titania sol depending on reaction conditions was investigated by a light scattering method and XRD analysis of frozen dried powders, respectively. This sol with photo catalytic nano titania particles was used to the following hydrophilic hybrid coating film's fabrication and its properties was evaluated. Subsequently, for coating film using the above mentioned aqueous titania sol, non-aqueous titania sol was prepared without any chemical additives and its time stability according to aging time was investigate. By using the above mentioned aqueous titania sol and non-aqueous sol, a complex oxide coating sol for metal and ceramic substrate and a organic-inorganic hybrid coating sol for polymer substrate was prepared and it's hydrophilicity depending on UV irradiation conditions was evaluated. As a conclusions, the following results were obtained. (1)Aqueous titania sol The average particle size of titania in formed aqueous titania sol was distributed between 20$\sim$90nm range depending on reaction conditions. And the crystal phase of titania powders obtained by frozen drying method was changed from amorphous state to anatase and subsequently transformed to rutile crystal phase and it is attributed to concentration gradient in aqueous sol. (2)Non-aqueous titania sol Non-aqueous titania sol was prepared using methanol as a solvent and a little distilled water for hydrolysis and nitric acid as a catalyst were used. The obtained non-aqueous titania sol was stable at room temperature for 20 days. Additionally, non-aqueous titania sol with addition of chealating reagent such as acethylaceton and ethylene glycol prolonged the stability of sol by six months. (3)Complex sol and hybrid sol with super hydrophilicity The above mentioned aqueous titania sol as a main photocataylic component and non-aqueous titania sol as a binder for coating process was used to prepare a complex sol used for metal, ceramic and wood material substrate and also to prepare the organic-inorganic hybrid sol for polymer substrate such as polycarbonate and polyethylene, in which process APMS(3-Aminopropyltrimethoxysilane), GPTS(3-Glycidoxypropyl-trimethoxysilane) as a hydrophilic silane compound and HEMA(2-Hydroxyethyl methacrylate) as a forming network in hybrid coating film were used. The hybrid coating film such as prepared through this process showed a superhydrophilicity below 1$10^{\circ}$ depending on processing conditions and a pencil's hardness over 6 H.

• Journal of the Korean Vacuum Society
• /
• v.10 no.2
• /
• pp.207-212
• /
• 2001

In this study, synthesis condition of $TiO_2$ thin films which have optimal dielectric characteristics using sol-gel method was determined. Thin films were fabricated using sol which have optimal characteristics and their permittivity was measured. In case of the amount of water for hydrolysis smaller than that for stoichiometry, sol formed clear sol which have normal chain structure. On the contrary, in case of the amount of water for hydrolysis larger than that for stoichiometry, sol formed suspended sol which have cluster structure. The permittivity of thin films increased exponentially around $^{\circ}C$.

• Journal of Integrative Natural Science
• /
• v.10 no.2
• /
• pp.110-114
• /
• 2017

The connected and simply connected four-dimensional matrix solvable Lie group $Sol^4_1$ is the four-dimensional geometry. A crystallographic group of $Sol^4_1$ is a discrete cocompact subgroup of $Sol^4_1{\rtimes}D(4)$. In this paper, we geometrically describe the crystallographic groups of $Sol^4_1$.

• Proceedings of the KIEE Conference
• /
• 2003.07c
• /
• pp.1433-1435
• /
• 2003

Ti-Sn sol is fabricated using sol-gel method. Initial viscosity of sol decreases with increasing HCl additive. Gelation of sol is retarded with increasing HCl additive. From the results of TG-DTA, the peaks of particular organics combustion do not occur because Sn sol is hydrolyzed sufficiently.

• Journal of the Korean Ceramic Society
• /
• v.32 no.1
• /
• pp.17-24
• /
• 1995

The TEA complex polymeric sol was prepared by the alkoxide sol-gel method. The purpsoe of this experiment was to vefity the particle shape in the sol from the investigation of the rheological properties. TEA retarded hydrolysis rate by the reaction with alkoxide enough to make a stable transparent sol in the wide range of composition. From the results of the viscosity change with time, the optimum mole ratio for spinning was selected as 0.5 mole of TEA, 3 mole of H2O and the optimum viscosity was 104 cPs. The rheological behavior of the sol showed that the particle shape in the sol was linear, which was adequate for fiber drawing.

• Journal of the Korean Ceramic Society
• /
• v.41 no.5
• /
• pp.349-352
• /
• 2004

Organic-inorganic hybrid sol based on ZrO$_2$-SiO$_2$ system was prepared by sol-gel process. Firstly, ZrO$_2$ non-aqueous precursor sol was synthesized and then organosilane compounds which include epoxy silane (GPTS; 3-g1ycidoxypropyl tri-methoxysilane) and acryl silane (ACS; (3-(tri-methoxysilyl)propylmethacrylate)) were added to ZrO$_2$precursor sol for hybridization. Finally, com-mercial silica sol was added to improve the mechanical properties. Synthesized organic-inorganic Zr-hybrid sol was coated on polycarbonate substrate for enhancing it’s mechanical properties, especially hardness. Vicker’s hardness of polycarbonate sub strate was increased from 13.6 to 17.8 MPa and its pencil hardness was increased from 2 to 7 H, respectively, after coating and drying at 10$0^{\circ}C$ for 30 min.

• Journal of the Korean Mathematical Society
• /
• v.44 no.5
• /
• pp.1121-1137
• /
• 2007

There are 7 types of 4-dimensional solvable Lie groups of the form ${\mathbb{R}^3}\;{\times}_{\varphi}\;{\mathbb{R}}$ which are unimodular and of type (R). They will have left. invariant Riemannian metrics with maximal symmetries. Among them, three nilpotent groups $({\mathbb{R}^4},\;Nil^3\;{\times}\;{\mathbb{R}\;and\;Nil^4)$ are well known to have lattices. All the compact forms modeled on the remaining four solvable groups $Sol^3\;{\times}\;{\mathbb{R}},\;Sol_0^4,\;Sol_0^'4\;and\;Sol_{\lambda}^4$ are characterized: (1) $Sol^3\;{\times}\;{\mathbb{R}}$ has lattices. For each lattice, there are infra-solvmanifolds with holonomy groups 1, ${\mathbb{Z}}_2\;or\;{\mathbb{Z}}_4$. (2) Only some of $Sol_{\lambda}^4$, called $Sol_{m,n}^4$, have lattices with no non-trivial infra-solvmanifolds. (3) $Sol_0^{'4}$ does not have a lattice nor a compact form. (4) $Sol_0^4$ does not have a lattice, but has infinitely many compact forms. Thus the first Bieberbach theorem fails on $Sol_0^4$. This is the lowest dimensional such example. None of these compact forms has non-trivial infra-solvmanifolds.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.234-235
• /
• 2007

Transparent nanosized $TiO_2$ sol has been made by sol-gel method, using Titanium(IV) isopropoxide precursor. To promote hydrolysis for titania is needed excess water, Oil bath and temperature about $80^{\circ}C$. $TiO_2$ sol is peptized ranging from pH 1 to 1.5 using hydrochloric acid for the stability of sol during a condensation reaction. The average particle size of $TiO_2$ sol was approximately 20nm. $TiO_2$-sillane sol was synthesized by surface treatment using MTMS to the $TiO_2$ sol. TEM analysis has been used to check the degree of dispersion and FT-IR analysis has been used to see if the sillane has been chemically bonded on the surface of $TiO_2$.