• The korean journal of orthodontics
• /
• v.36 no.6
• /
• pp.451-464
• /
• 2006

The purpose of this study was to search for an appropriate method of coating $TiO_2$ on orthodontic appliances. $TiO_2$ thin films were deposited on orthodontic wires and brackets using sol-gel, CVD (Chemical Vapor Deposition) and PE-CVD (Plasma Enhanced-CVD) methods. The roughness of $TiO_2$-coated surfaces was investigated via scanning electron microscope (SEM) and adhesive strength of $TiO_2$ thin films was measured by adhesive tape pull test. Methylene blue degradation test was carried out to evaluate the photocatalytic activity of $TiO_2$ and the corrosion resistance of $TiO_2$ thin films against fluoride solution was also analyzed by observing the surfaces of $TiO_2$-coated wires and brackets via SEM after immersion in sodium fluoride solution. Through the comparison of properties and photocatalytic activity of $TiO_2$ thin films according to the coating methods, the following results were obtained. Smoother surfaces of $TiO_2$ thin films were generated by CVD or PE-CVD methods than through the sol-gel method or the control. Adhesive strength of the $TiO_2$ thin films was highest in PE-CVD and gradually became lower in the order of CVD, then the sol-gel method. Photocatalytic activity of $TiO_2$ thin films on methylene blue was the highest in PE-CVD and gradually became lower in the order of CVD, then the sol-gel method. Corrosion resistance of $TiO_2$ thin films against fluoride solution was stronger in CVD and PE-CVD methods than in the sol-gel method. The results of this study suggest that the CVD or PE-CVD methods is more appropriate than the sol-gel method for $TiO_2$ coating on orthodontic wires and brackets.

• Journal of Ocean Engineering and Technology
• /
• v.29 no.1
• /
• pp.94-99
• /
• 2015

Lead zirconate titanate (PZT) thick films with thicknesses of ㎛ were fabricated on silicon substrates using an aerosol deposition method. A PZT powder solution was prepared using a sol-gel process. The average diameters (d50) obtained were 1.67, 1.98, and 2.40μm when the pyrolysis temperatures were 300℃, 350℃, and 450℃ respectively. The as-deposited film had a uniform microstructure without any cracks or pores. The as-deposited films on silicon were annealed at a temperature of 700℃. The 20-㎛-thick PZT film showed good adherence between the PZT film and substrate, with no tearing observed in the conventional solid phase process. This was probably because the presence of pores produced from organic residue during annealing relieved the residual stresses in the deposited film.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2003.07a
• /
• pp.484-485
• /
• 2003

We report on the optimization of the fabrication process of hybrid sol-gel thin film deposition to produce low cost $1 {\times} 16$ splitters for optical communications. We learn that sol-gel film thickness is dependent upon the spinning speeds and viscosity of the sol-gel solutions and refractive index upon the dopant concentrations of Al and Zr in the sol solutions. We could find the optimized physical conditions to achieve the desired thickness of core and cladding layers. We will further carry out the fabrication and measurements of insertion loss, polarization dependent loss (PDL), etc. for the performance of fabricated splitter devices.

• Journal of the Korean Ceramic Society
• /
• v.52 no.5
• /
• pp.366-373
• /
• 2015

Sol-gel binder was prepared by hydrolysis and condensation reaction using boehmite sol and methyltrimethoxysilane as a function of aging-time. The coating slurry was composed of a plate-shape alumina in the sol-gel binder for the EPD process, in which particles dispersed in the slurry were deposited on the electrode under an electric field due to the surface charge. We studied the effects of three parameters: the content of boehmite, the aging time, and the applied voltage, on the physical, thermal, and electrical properties of the hybrid composite films by EPD. The amount of boehmite was 10 ~ 20 wt% and the aging time was 0.5 ~ 72, with a fixed amount of plate-shape alumina of 10 wt%. The condition of applied voltage was 5 ~ 30 V with a distance of 2 cm between the electrode during the EPD process. We confirmed that a structure of hybrid composite films of well-ordered plate alumina was deposited on the substrate when the film was prepared using a sol-gel binder composed of 15 wt% boehmite with 1 hr aging time and EPD at 10 V. The process shows a weight loss of 7% at $500^{\circ}C$ in TGA and a breakdown voltage of 8 kV at $87{\mu}m$.

• The Korean Journal of Ceramics
• /
• v.6 no.1
• /
• pp.15-20
• /
• 2000

Thick inorganic-organic hybrid films were prepared on ITO-coated glass substrates by the electrophoretic sol-gel deposition of polyphenylsilsesquioxane particles. The morphology of the deposited films changed from the aggregate of the spherical particles to monolith by heat treatment at temperatures higher than $200^{\circ}C$. Transparency of the films was significantly improved accompanied by the morphological change of the particles. The degree of the morphological change was governed by two factors; maximum heat treatment temperature and heating rate. Transparent thick films of ca. 3$\mu\textrm{m}$ in thickness were obtained only by heat treatment at $400^{\circ}C$ for 2h with rapid heating from room temperature to $400^{\circ}C$. These films obtained were strongly adhered to the ITO-coated glass substrates and has a very smooth surface.

• Journal of the Korean Ceramic Society
• /
• v.40 no.4
• /
• pp.380-384
• /
• 2003

The effects of the mole concentrations of precursor solution on the microstructure and dielectric properties of sol-gel deposited $Ba_{0.85}$S $r_{0.15}$Ti $O_3$(BST) thin films have been investigated. The films were of single perovskite phase with strong (100) preferred orientation when grown on LaNi0$_3$ buffered Pt/Ti/ $SiO_2$Si substrates using a diluted precursor solution. Variation of the precursor solution concentration resulted in a different microstructure and, in turn, affected the tunability of the sol-gel deposited films. It was observed that leakage currents increased asymmetrically for the negative and positive bias voltage with decreasing thickness. Overall results suggest that those BST films have acceptable properties f3r applications as room-temperature tunable elements.

• Membrane Journal
• /
• v.11 no.3
• /
• pp.124-132
• /
• 2001

Silica membranes were prepared on a porous ${\alpha}$-alumina tube with pore size of 150nm by sol-gel and chemical vapor deposition(CVD) method for hydrogen separation at high temperatures. Silica and ${\gamma}$-lumina membranes formed by the sol-gel method possessed a large amount of mesopores of a Knudsen diffusion regime. In order to improve the $H_2$ selectivity, silica was deposited in the sol-gel derived silica/${\gamma}$-alumina layer by thermal decomposition of tetraethyl orthosilicate(TEOS) at $600^{\circ}C$. The CVD with forced cross flow through the porous wall of the support was very effective in plugging mesopores that were left unplugged in the membranes. The CVD modified silica/alumina composite membrane completely rejected nitrogen permeation and thus showed a high $H_2$ selectivity by molecular sieve effect. the permeation of hydrogen was explained by activated diffusion and the activation energy was 9.52kJ/mol.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.431.1-431.1
• /
• 2014

최근, 높은 캐리어 이동도와 유연성, 투명성의 우수한 전기적 기계적 특성을 갖는 그래핀에 관한 연구가 활발해지고 있으며 이를 기반으로 한 그래핀 field effect transistor (FET) 센서 응용 또한 관심이 커지고 있다. 작은 소자 크기, 견고한 구조, 빠른 응답속도와 CMOS 공정과의 호환성이 좋은 FET 기반의 센서의 감지 특성은 주로 전해질과 직접 접촉하는 게이트 절연체의 고유 특성에 의해 결정된다. 이러한 게이트 절연체는 일반적으로 스퍼터링, atomic layer deposition (ALD), plasma enhanced chemical vapor deposition (PECVD) 등의 진공 방법에 의해 형성되며, 이 공정 기술은 고가의 장비, 긴 공정 시간과 높은 제조비용이 요구된다. 더욱이, 위의 방식들은 소자 제작 동안에 플라즈마 발생 또는 열처리를 필요로 하게 되며 이는 그래핀 기반의 소자의 제작에 있어 큰 손상을 발생시키게 된다. 이러한 이유로 인해, 그래핀 FET 센서의 게이트 절연체의 형성에 있어 진공 증착 기술은 적절하지 않다. 본 연구에서는, 진공 증착 기술의 문제점을 극복하기 위해 sol-gel 방식을 통한 Al2O3 게이트 절연체를 갖는 그래핀 FET 센서를 제작하였다. Sol-gel 방식은 적은 비용, 공정의 단순화, 높은 처리량 뿐 아니라 소자의 대면적화 제작에 유리하다는 장점을 가지며, 또한 게이트 절연체를 증착함에 있어서 플라즈마가 발생하지 않기 때문에 그래핀 FET 제작에 쉽게 적용될 수 있다. 특히, 게이트 절연체 중 Al2O3은 우수한 화학적 안정성과 감지 특성으로 인해 본 실험에 사용하였다. 결론적으로, sol-gel 방식을 통한 Al2O3 게이트 절연체를 갖는 그래핀 FET 센서는 우수한 전기적 특성과 감지 특성 측면에서 매우 전망적이다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07b
• /
• pp.714-718
• /
• 2003

Usually for the commercial preparation of barium titanate films or ceramics the reaction atmosphere must be preferably in air. However, normally air is not used because it contains carbon dioxide, which can easily react with barium to form the undesired product barium carbonate, leading to unwanted second-phase formation in the (mal stages of the process. In the present work a series of perovskite barium titanate films was prepared by the sol-gel method, using a metal alkoxide solutions in the electrophoretic deposition (EPD). The influence of several process parameters, like sintering temperature of sol preparation before EPD and heat-treatment temperature and non-oxidized atmosphere, on the film properties is described.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2008.10a
• /
• pp.806-808
• /
• 2008

We studied ink-jet printing for selective deposition of soluble oxide semiconductor to fabricate transistor. Sol-gel derived ZTO solution was synthesized for ink-jet printable solution. Transistors were produced by printing oxide layer between ITO electrodes. We demonstrated that ink-jet printed ZTO transistors work well and surface treatment significantly influences device performance.