• Tribology and Lubricants
• /
• v.37 no.2
• /
• pp.77-80
• /
• 2021

In this study, we investigated the effect of the spring constant on frictional behavior at a nanoscale through molecular dynamics simulation. A small cube-shaped tip was modeled and placed on a flat substrate. We did not apply the normal force to the tip but applied adhesive force between the tip and the substrate. The tip was horizontally pulled by a virtual spring to generate relative motion against the substrate. The controlled spring constant of the virtual spring ranged from 0.3 to 70 N/m to reveal its effect on frictional behavior. During the sliding simulation, we monitored the frictional force and the position of the tip. As the spring constant decreased from 70 to 0.3 N/m, the frictional force increased from 0.1 to 0.25 nN. A logarithmic relationship between the frictional force and spring constant was established. The stick-slip instability and potential energy slope increased with a decreasing spring constant. Based on the results, an increase in the spring constant reduces the probability of trapping in the local minima on the potential energy surface. Thus, the energy loss of escaping the potential well is minimized as the spring constant increases.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2001.10a
• /
• pp.255-259
• /
• 2001

The spring constant of a micro coil spring was measured by uniaxial tensile test. The inner diameter of it is $35{\mu}m$ and the pitch size is about $23{\mu}m$. A suing constant measurement system was developed. It consists of control units, load cell units, linear stages and several specially designed jigs and fixtures. Load and displacement are measured using a commercial load cell of 1000g capacity and a magnetic scale of $0.5{\mu}m$ resolution. In this study, a method to measure the spring constant of micro coil spring is presented and the relationship between misalignment of specimen and measurement error is discussed.

• Proceedings of the KSME Conference
• /
• 2001.11b
• /
• pp.682-687
• /
• 2001

This study represents effect of exhaust performance by according to active muffler valve spring. The experimental parameter were divided engine speed and torsion coil spring constant. The sound pressure level was generally low at engine speed 2000-2500rpm but That was showed the lowest at spring constant k=0.75. Flow speed of exhaust gas was showed the fast at spring constant k=0.75 but the low value was showed at k=0.97. It was contained a rather low concentration of carbon monoxide(CO) at engine speed 2000-2500rpm and k=0.81, low concentration of hydrocarbon(HC) at spring constant k=0.81 but that was high at spring constant k=0.97. A conclusion based on FFT analysis was generally low concentration value at k=0.79 and k=0.81. The temperature distributions into the muffler was shown similar conditions. Heat transfer was well spreaded at thermocouple No.8 because valve was opened.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.27 no.2
• /
• pp.215-222
• /
• 2003

In this paper, kinematic analysis and design of constant force mechanisms which employ a linear spring are studied. Firstly, sufficient conditions for the mechanisms to be the constant force mechanisms are derived in terms of displacement variables through the kinematic analysis. Secondly, a few conceptual mechanisms satisfying these constraints are proposed.

• Proceeding of EDISON Challenge
• /
• 2015.03a
• /
• pp.263-265
• /
• 2015

In this paper, a coil spring of the suspension components of the car is calculated through FEM(Finite Element Method) when a portion of the one is applied by an external load. we analyze the situation by using 'Large Deformation Analysis SW' in the EDISON structural dynamics server. Results of the analysis are about a displacement of the upper spring after deformation and total mass, and we use them to calculate the spring constant and maximum von-Mises stress by using Hooke's law and von-Mises stress equation. Finally, we visualize the relationship between the calculated spring constant and the mass through graphs and this data are beneficial for industries related to the spring.

• Journal of Power System Engineering
• /
• v.18 no.2
• /
• pp.77-82
• /
• 2014

The air spring is widely used in various fields such as a suspension system and an anti-vibration system because the natural frequency is kept constant regardless of the change in the load, spring constant is easy to change, and, vibration and shock isolation performance are excellent. The purpose of this study is to derive a nonlinear governing equation of an air spring, to analyze the effect of the various parameters on the dynamic stiffness of the air spring, and, to suggest a more efficient design method of an air spring system. In order to do so, this study investigates the impact of all the parameters that could affect the dynamic stiffness of the air spring while changing the excitation amplitude and the frequency with a developed governing equation.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.12 no.11
• /
• pp.5300-5305
• /
• 2011

Displacement, contact pressure and moment which are developed in rigid beam on the Winkler foundation and 2 parameter Winkler foundation were derived. It can be seen that moment distribution along with rigid beam on the Winkler foundation are regardless of spring constant and the moments calculated from assuming linear spring constant were greater than those from assuming constant spring constant. Simple calculation revealed that the maximum moment developed in the rigid beam on the 2 parameter Winkler foundation was larger than that developed in the rigid beam on the Winkler foundation.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.05a
• /
• pp.82-88
• /
• 2002

A simple beam subjected to a uniformly distributed tangential follower force and the successive two moving spring-mass systems upon it constitute this vibration system. The influences of the velocities of the moving spring-mass system, the distance between the successive two moving spring-mass systems and the uniformly distributed tangential follower force have been studied on the dynamic behavior of a simple beam by numerical method. The uniformly distributed tangential follower force is considered within its critical value of a simple beam without the successive two moving spring-mass systems, and three kinds of constant velocities and constant distance of the successive two moving spring-mass systems are also chosen. Their coupling effects on the transverse vibration of the simple beam are inspected too.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.13 no.3
• /
• pp.202-209
• /
• 2003

A simply supported beam subjected to a uniformly distributed tangential follower force and the two successively moving spring-mass systems upon it constitute this vibration system. The influences of the velocities of the moving spring-mass system, the distance between two successively moving spring-mass systems and the uniformly distributed tangential follower force have been studied on the dynamic behavior of a simply supported beam by numerical method. The uniformly distributed tangential follower force is considered within its critical value of a simply supported beam without two successively moving spring-mass systems, and three kinds of constant velocities and constant initial displacement of two successively moving spring-mass systems are also chosen. Their coupling effects on the transverse vibration of the simply supported beam are inspected too. In this study the simply supported beam is deflected with small vibration proportional to natural frequency of the moving spring-mass systems. According to the increasing of initial displacement of the moving spring-mass systems the amplitude of the small vibration of the simply supported beam is increased due to the spring force. The velocity of the moving spring-mass system more affect on the transverse deflection of simply supported beam than other factors of the system and the effect is dominant at high velocity of the moving spring-mass systems.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.7 no.5
• /
• pp.113-119
• /
• 1998

Air spring has the advantages to be nearly constant in natural frequency inspite of load change, and to be able to control height level. Half-long taper spring has the advantages to function as well link as spring. Thus to utilize two type spring's advantages, half-long taper spring and air spring are combined and used. In this study, the theory to calculate the characteristics in combination is developed.