• Journal of Advanced Navigation Technology
• /
• v.26 no.5
• /
• pp.344-349
• /
• 2022

A compact LPDA antenna consisting of right triangle-shaped dipole elements appended with strips is proposed for UWB applications. First, right triangle-shaped dipole elements are used instead of conventional strip dipole elements to reduce the width of the LPDA antenna. Second, the spacing between the LPDA elements is decreased to reduce the length of the LPDA antenna. Finally, strips are appended at the ends of the right triangle-shaped dipole elements in order to further reduce the width of the antenna. A prototype of the proposed antenna with 16 elements and gain > 4 dBi is fabricated on an FR4 substrate with dimensions of 44 mm×30 mm. Measured frequency band of the fabricated antenna is 2.99-14.76 GHz for a VSWR < 2, which ensures UWB operation, and measured gain range is 4.0-5.5 dBi with a front-to-back ratio larger than 10 dB. The length and width of the proposed compact LPDA antenna are reduced by 40.9% and 20.6%, respectively, compared to the conventional LPDA.

• Journal of Korean Society on Water Environment
• /
• v.38 no.5
• /
• pp.211-219
• /
• 2022

In this study, the effect of liquid height/volume on sonochemical oxidation reactions was investigated in 300 kHz sonoreactors. The gas mixture of Ar/O₂ (50:50) was applied in two modes including saturation and sparging, and zero-order reaction (KI dosimetry) and first-order reaction (Bisphenol A (BPA) degradation) were used to quantitatively analyze sonochemical oxidation reactions. For the zero-order reaction, the highest sonochemical oxidation activity was obtained for the liquid height of 5𝛌, and the lowest height for both the gas saturation and sparging conditions. In addition, the sparging did not enhance the sonochemical oxidation activity for all height conditions except for 50𝛌, where very low activity was obtained. It was found that in sonochemiluminescence (SCL) images the sonochemical active zone was formed adjacent to the liquid surface for the gas sparging condition due to the formation of the standing wave field while the active zone was formed adjacent to the transducer at the bottom due to the blockage of ultrasound. For the first-order reaction, the highest activity was also obtained at 5𝛌 and the comparison based on the reactant mass was not appropriate because the concentration of the reactant (BPA) decreased significantly as the reaction time elapsed. Consequently, it was revealed that the determination of optimal liquid height (ultrasound irradiation distance) based on the wavelength of the applied ultrasound frequency was very important for the optimal design of sonoreactors in terms of reaction efficiency and reactor size.

• Journal of Aerospace System Engineering
• /
• v.17 no.4
• /
• pp.110-117
• /
• 2023

In this paper, the optimal placement of the rotary wing's communication and navigation antennas was evaluated by measuring their performance through ground simulations and flight tests. To select the mounting position of the communication and navigation antenna on the helicopter, after considering the shape and characteristics of the airframe, the radiation patterns, coupling analysis, equipment operation profiles, and antenna type analysis were performed for the aircraft-mounted antenna. Based on the analysis results, a procedure for sequentially performing voltage standing wave ratio (VSWR) measurement and antenna pattern test was established through ground and flight tests of the antenna. The systematic performance measurement method and procedure proposed in this paper were verified through ground and flight tests of the Light Armed Helicopter (LAH) system.

• Journal of Advanced Navigation Technology
• /
• v.25 no.6
• /
• pp.523-529
• /
• 2021

This paper shows the design and fabrication of antenna embedded in marine buoy for marine IoT service, especially automatic identification system of fishing gears. Frequency band of proposed antenna has dual band of 433 MHz and 920 MHz considering marine IoT extension. Dual pattern monopole type for 920 MHz and meander type for 433 MHz are adopted in the proposed antenna. Voltage standing wave ratio is obtained 1.548 at 433 MHz and obtained 1.5 of mean value at 920 MHz band by measuring the fabricated antenna. The maximum antenna gain of 3.83 dBi is measured at 902 MHz among 920 MHz band, while antenna gain of 433 MHz is obtained 1.18 dBi. Although antenna gain of 433 MHz is low than 920 MHz band, this gain is larger than desired value of -5 dBi. And, it is confirmed that other measured values meet the performance criteria for archiving communication distance of 10 km between marine buoy and fishing ship in automatic identification system of fishing gears.

• Journal of Advanced Navigation Technology
• /
• v.28 no.1
• /
• pp.136-141
• /
• 2024

In this paper, a broadband inset-fed microstrip patch antenna operating at 10.525 GHz band was proposed. The proposed broadband inset-fed microstrip patch antenna consists of three narrow rectangular patches. At the center of the center patch, two symmetrical side patches were connected by a strip conductor and were arranged with their centers shifted in a perpendicular direction with respect to the center patch. For performance comparison, a conventional inset-fed square microstrip patch antenna was designed. Experiment results show that the frequency band of the measured input reflection coefficient with a voltage standing wave ratio less than 2 for the broadband inset-fed microstrip patch antenna was 10.036-11.051 GHz (9.63%), whereas that for the conventional inset-fed rectangular microstrip patch antenna was 10.306-10.772 GHz (4.42%). Therefore, the input reflection coefficient frequency bandwidth of the fabricated broadband inset-fed microstrip patch antenna was increased by 2.18 times, compared to the conventional inset-fed square microstrip patch antenna.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.7 no.4
• /
• pp.207-215
• /
• 2004

Recently, securing a vast land in the land region becomes more difficult and efforts to seek its alternation in the sea area have been increased. As a consequence, the coastal region has been faced to extensive beach erosion problems. In planning offshore structures such as artificial islands, it is necessary to forecast the influence of the structure construction exerting on the beach erosion of the adjacent coast. In the present study, the sediment movement pattern behind offshore structure was examined through a series of three dimensional movable bed experiments, so as to develop the numerical model which forecasts morphological change including beach erosions. The experimental results reveal that the sediment movement patterns of the beach line side and the depth region are separated at a certain boundary line. In details, at the beach side including swash zone the sediment movement becomes dominant, which is governed by a relation between depth contours and incident wave directions, while at the depth region the bed load and suspended load due to the orbit motion of waves are carried by nearshore currents, and both movements are clearly separated at a specified boundary that is related to partial standing wave from the beach. It is expected that these results can be effectively used for verification of a numerical model on morphological change of the coast.

• The Journal of the Acoustical Society of Korea
• /
• v.20 no.5
• /
• pp.69-75
• /
• 2001

In this paper, a fast and easy impedance matching method, which could give the impedance matching component for the general 1 or 2-port network was introduced. First, the entire network structure was defined which consists of the network part to be matched and the impedance matching part composed of inductors and capacitors. Next, the transmission matrix and input and output impedances of the entire network from the terminal impedance conditions were calculated, then the exact solutions for the matching components were obtained. To verify the efficiency of this method, this method was applied to the CDMA If band withdrawal weighted SAW transversal filter, and investigated the effects of the impedance matching before and after, through the simulation and experiment. As the result, the performance of a fractional bandwidth of 1.2%, insertion loss of 29 dB, and VSWR of 80 have improved to a factional bandwidth of 1.8％, insertion loss of 9 dB, VSWR of 3 at 85.38 MHz center frequency. The result shows that this impedance matching method could be used in the SAW devices and other types of 1 or 2-port network.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.41 no.11
• /
• pp.891-899
• /
• 2013

This paper suggests a test and evaluation procedure of conformal load-bearing antenna structure(CLAS) for high speed military jet application. A log periodic patch type antenna was designed for multi-band communication and navigation antenna. Carbon/Glass fiber reinforced polymer was used as a structure supporting aerodynamic loads and honeycomb layer was used to improve antenna performance. Multi-layers were stacked and cured in a hot temperature oven. Gain, VSWR and polarization pattern of CLAS were measured using anechoic chamber within 0.15~2.0 GHz frequency range. Tension, shear, fatigue and impact load test were performed to evaluate structural strength of CLAS. Antenna performance test after every structural strength test was conducted to check the effect of structural test to antenna performance. After the application of new test and evaluation procedure to validate a new CLAS, a design improvement was found.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.29 no.1
• /
• pp.42-49
• /
• 2018

In this paper, a dual-band microstrip-fed monopole antenna with a DGS(defected ground structure) for WLAN(wireless local area network) applications is presented. The antenna consists of a monopole and a defected ground, which were etched on both sides of the FR-4 substrate. The defected ground structure was used to obtain the dual band, while the step-by-step reduction in the monopole width was used to improve the impedance matching of the antenna. The antenna has an overall compact size of $44{\times}51{\times}1.6mm^3$, which was optimized by varying the size of the monopole and the ground plane such that it may resonate at the 2.4 GHz and 5 GHz bands of the WLAN. The measurement results showed that the antenna operates in the frequency band of 210 MHz(2.29~2.50 GHz) and 900 MHz(5.05~5.95 GHz) for a VSWR under 2, and showed omnidirectional radiation pattern at all desired frequencies.

• KOREAN JOURNAL OF PACKAGING SCIENCE & TECHNOLOGY
• /
• v.19 no.2
• /
• pp.103-108
• /
• 2013

Packaging of solar salts produced in Korea and Japan were evaluated and compared each other in terms of packaging design such as package types, colors and graphics. The standing pouch type in plastic film was most popular for the Korean salts regardless of the package capacity. But the same type was common only for the lower package capacity of 300 g or less while the plastic film pouch was prevalent for the higher capacity for the Japanese salts. White and brown were dominant colors for the Korean solar salts reminding us of salt farms and the foreshore respectively and strengthening its color identity. White, blue and red were used for the dominant, assort and accent colors respectively for the Japanese salt packaging. Salt farmers and the foreshore are often represented as the main package graphics for the Korean solar salts while the wave symbolising the sea was found frequently for the Japanese ones. The word of 'Shinan' was involved the most in the brand names of the Korean salts and the sea was appeared very often in those of the Japanese ones.