• Journal of Korean Association for Spatial Structures
• /
• v.16 no.1
• /
• pp.35-42
• /
• 2016

Until recently, almost all ETFE film structures that have been erected is the cushion type because there are problems at lower allowable strength under elastic range and viscosity behaviour such as creep and relaxation of ETFE films under long-term stresses. But the number of tension type structures is currently increasing. This paper proposes the stretch fabrication of ETFE film to verify the applicability of ETFE films to tensile membrane structures. First of all, to investigate the possibility of application on tensile membrane structures, the stretch fabrication test is carried out, and it is verified that it is possible to increase the yield strength of the film membrane structures. After simulating the experiment also carries out an analytical investigation, and the effectiveness of the elasto-plastic analysis considering the viscous behavior of the film is investigated. Finally, post-aging tension measurement is conducted at the experimental facilities, and the viscosity behavior resulting from relaxation is investigated with respect to tensile membrane structures.

• Journal of Korean Association for Spatial Structures
• /
• v.14 no.3
• /
• pp.85-92
• /
• 2014

Most of the structural forms in which ETFE film is used are the cushion(pneumatic membrane structures) and tension type(tensile membrane structures), which have been generally accepted to be the most efficient forms. Tensile membrane structures are pulled outward from the exterior to introduce initial stress. And such structures offer the advantage of a natural shape formed by tensile stress and eliminate the need for blast air. Recently, the number of tension type structures is increasing. However, there are problems of creep and relaxation of ETFE films under long-term stresses. In this paper, the stretch fabrication method is proposed for stretching the film into the plastic region during initial tensioning as a way to increase its strength. And its effectiveness is confirmed by investigating experimental and analytical test using ETFE films.

• Proceedings of the KIEE Conference
• /
• 1994.07b
• /
• pp.1394-1396
• /
• 1994

Polyimide thin films were fabricated an using vapor deposition polymerization apportus, and their FT-IR and TGA characteristics were investigated. The peaks of $720cm^{-1}$ and $1380cm^{-1}$ show C=O stretch mode and C-N stretch mode, and that of the cured polyimide at $350^{\circ}C$ were sturated. $T_d$(Depolymerization temperature) was showed at $405^{\circ}C$ from research of thermal resistivity characteristics by TGA It was possible to fabrication of polyimide thin film by VDPM.

• Proceedings of the KIEE Conference
• /
• 1996.07c
• /
• pp.1639-1641
• /
• 1996

Polyirnide thin films were fabricated an using vapor deposition polymerization apparatus, and their FT-IR and TGA characteristics were investigated. The peaks of $720cm^{-1}$ and $1380cm^{-1}$ show C=O stretch mode and C-N stretch mode, and that of the cured polyimide at $300^{\circ}C$ were saturated. TGI(Thormogravi metric index) was showed at $459^{\circ}C$ from reaserch of thermal resistivity characteristics by TGA.

• Korean Journal of Applied Biomechanics
• /
• v.22 no.4
• /
• pp.421-428
• /
• 2012

The purpose of this study was to verify the effects of developed assisting wear which maximize trunk(back) muscle's stretch-shortening effect during backswing and downswing for increasing golf ball carrying distance. Design and fabrication of assistive wear were performed based on the results of analyzed data of trunk EMG activity from the golf drive swings of elite professional male golfers during back swing and downswing phases. After the prototype of wear was produced, surface EMG and Flight scope tests were conducted to verify the effectiveness of the wear for increasing distance to the professional golfers. Results indicated that wearing trial showed significant longer carry distance than the non-wearing trial(p<.001). The carry distance of wearing trial showed an average 229 m compared to the non-wearing trial, the average 225 m. The swing with wearing also produced significantly faster ball speed than the trial without wearing(p<.05). Average 245 Km/h and 244 Km/h were produced for the swing with and without wearing trails, respectively. EMG results also indicated that the muscle activity of left psoas was significantly increased for wearing trial during downswing and near the impact. Thus, this may affect positively to increase club head speed. The activity of the left latissimus dorsi was dramatically increased during the final stage of swing. This generates elongation effect for longer follow-through and increased impulse between club and ball so eventually valid assistance to increase carry distance. Therefore, the developed assisting wear was proved to be effective tool for increasing golf ball carry distance with maximizing trunk(back) muscle's stretch-shortening effect during backswing and downswing.

• Textile Coloration and Finishing
• /
• v.27 no.2
• /
• pp.126-131
• /
• 2015

Silica-polyurethane hybrid breathable films were prepared and their breathabilities were assessed. Appropriately aggregated silica was prepared through sol-gel reaction of water glass and its particle size ranged 360~500nm. The polyurethane dispersion was prepared by the reaction of isophorone diisocyanate(IPDI) as diisocyanate and polytetramethylene glycol(PTMG) and dimethylol propionic acid(DMPA) as polyol, particle size ranging 30~120nm. The reaction between isocyanate and hydroxyl group to form urethane bonding was checked by the intensity of the stretch peak of isocyanate at $2270cm^{-1}$ in the FT-IR. The silica was incorporated into polyurethane dispersion and casted into film. It was shown that the incorporated silica(1~5wt.%) increased water vapour permeability of the films by 30~100%, and decreased the hydrostatic pressure by 10~40%. From the results, it could be concluded that the appropriate hybridization of silica can increase the breathability of polyurethane dispersion film, while minimizing the loss of hydrostatic pressure.

• Journal of the Korean Vacuum Society
• /
• v.20 no.4
• /
• pp.276-279
• /
• 2011

Polymer electrostrictor materials can exhibit high electroactive strain and hold increasing promise for a variety of actuator applications. The size of available actuators has been limited, however, by the solution-based casting and annealing process generally required to prepare electrostrictor actuator materials. We report on a high throughput melt and stretch extrusion process capable of creating large sheets of an electrostructive terpolymer, poly (vinylidene fluoride-trifluoroethylene-1, 1-chlorofluoroethlene) while producing a suitable crystallinity and crystal phase for high strain electrostrictor performance such as artificial muscle systems.

• Science of Emotion and Sensibility
• /
• v.24 no.2
• /
• pp.49-56
• /
• 2021

In this study, we investigated the necessary mechanical properties of conductive multifilament yarns for fabricating the electrodes of biosignal measurement pressure and stretch textile sensors using embroidery. When electrodes and circuits for smart wearable products are produced through the embroidery process using conductive multifilament yarns, unnecessary material loss is minimized, and complex electrode shapes or circuit designs can be produced without additional processes using a computer embroidering machine. However, because ordinary missionary threads cannot overcome the stress in the embroidery process and yarn cutting occurs, herein, we analyzed the S-S curve, thickness, and twist structure, which are three types of silver-coated multifilament yarns, and measured the stress in the thread of the embroidery simultaneously. Thus, the required mechanical properties of the yarns in the embroidery process were analyzed. In the actual sample production, cutting occurred in silver-coated multifilament rather than silver-coated polyamide/polyester, which showed the lowest S-S curve. In the embroidery process, the twist was unwound through repetitive vertical movement. Further, we fabricated a piezoresistive pressure/tension sensor to measure gauge factor, which is an index for measuring biological signals. We confirmed that the sensor can be applied to the fabrication of embroidery electrodes, which is an important process in the mass production of smart wearable products.

• Fashion & Textile Research Journal
• /
• v.24 no.6
• /
• pp.694-706
• /
• 2022

This study focusses on the development of a motion-sensing smart leggings prototype with the help of a module that monitors motion using a fiber-type stretch sensor. Additionally, it acquires data on Electrocardiogram (ECG), respiration, and body temperature signals, for the development of smart clothing used in online exercise coaching and customized healthcare systems. The research process was conducted in the following order: 1) Fabrication of a fiber-type elastic strain sensor for motion monitoring, 2) Positioning and attaching the sensor, 3) Pattern development and three-dimensional (3D) design, 4) Prototyping 5) Wearability test, and 6) Expert evaluation. The 3D design method was used to develop an aesthetic design, and for sensing accurate signal acquisition functions, wearability tests, and expert evaluation. As a result, first, the selection or manufacturing of an appropriate sensor for the function is of utmost importance. Second, the selection and attachment method of a location that can maximize the function of the sensor without interfering with any activity should be studied. Third, the signal line selection and connection method should be considered, and fourth, the aesthetic design should be reflected along with functional verification. In addition, the selection of an appropriate material is important, and tests for washability and durability must be made. This study presented a manufacturing method to improve the functionality and design of smart clothing, through the process of developing a prototype of motion-sensing smart leggings.