• Transactions of the Korean Society of Mechanical Engineers
• /
• v.17 no.10
• /
• pp.2624-2633
• /
• 1993

Mass transfer experiment by naphthalene sublimation method has great advantages in measurement of local transfer coefficients in the region of a three dimensional flow or for a model of complex geometry, which is considered to be very difficult with conventional heat transfer measurements. Mass transfer data obtained by naphthalene sublimation technique are converted to the heat transfer data through heat/mass transfer analogy. This analogy is valid for a simple or laminar flow, but new insight is needed when applying to a turbulent flow or complex flow such as separation, reattachment and recirculation, The purpose of this research is to investigate how geometries and flow conditions incorporate heat/mass transfer analogy. Mass transfer experiments are performed using naphthalene sublimation technique for a flat plate, a circular cylinder, and rectangular cylinders. And mass transfer data are compared with earlier heat transfer measurements for the same geometries. Usefulness of analogy relation between heat and mass transfer is examined with these results.

• The Research Journal of the Costume Culture
• /
• v.26 no.5
• /
• pp.754-763
• /
• 2018

This study examined the color reproducibility and color fastness of digital textile printing for nylon sublimation transfer. After measuring the temperature and time suited to nylon sublimation transfer, the researchers conducted various tests for comparison and analysis including polyester transfer paper on polyester fabric to check dyeing characteristics, color change, sharpness, and the rubbing fastness of the dyeing samples for nylon sublimation transfer. These tests produced the following results. At $185^{\circ}C$ and $187^{\circ}C$, the sublimation transfer dyeing characteristics of nylon were similar to those of polyester and the researchers even observed superior color development in some colors; at a low temperature of $180^{\circ}C$, the sample that was worked on had the lowest level of color development. The examination of color difference (${\Delta}E$), which compared $L^*a^*b^*$ values, showed that the ${\Delta}E$ value of magenta was 10.34, that of yellow was 24.70, and that of black was 15.28. These results highlight the important role of heat treatment temperature and time on color development in nylon sublimation transfer. Concerning sharpness, the samples subjected to higher temperature heat treatment exhibited fewer color spreading phenomena around lines. Thus, dyeing properties and fastness can be enhanced by elongating time at low temperatures and shortening time at high temperatures; however, considering production time constraints as well as the need to produce industrially marketable quantities, the findings of this study suggest that the heat treatment temperature most suitable for nylon sublimation transfer is $187^{\circ}C$ for a duration of 50 seconds.

• Journal of the Korea Fashion and Costume Design Association
• /
• v.12 no.4
• /
• pp.207-221
• /
• 2010

This study aim to suggest how alter the korean traditional image design for umbrellas by sublimation transfer digital textile printing. Umbrellas are highly depend on design and made from polyester fiber which is proper item to utilize sublimation transfer digital textile printing. Sublimation transfer digital textile printing system can use computer system to create the delicate high dense images and one full layout through the hole umbrella. It can create distinctive style of design compare with former screen printing umbrella design. As a result of this study, Korean traditional images were adopted and recreated for umbrellas as the modern practical item. 7 of umbrella designs were developed and sample umbrellas could be produced in short period comparing with screen printing process. Through this study, as green printing process, sublimation transfer digital textile printing will be more applied to manufacture high quality textile products along with design development, thus it is expected as an alternative plan to leads growth of umbrella industries.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.14 no.5
• /
• pp.1300-1310
• /
• 1990

Naphthalene sublimation technique is employed to investigate the mass transfer processes from a square cylinder at various Reynolds numbers and various angles of attack. Distribution of the local mass transfer coefficients on each face of the cylinder changes dramatically with the angle of attack. Such variation of local mass transfer rates closely connected with the complex flow phenomena such as stagnation, acceleration, separation, reattachment and vortex shedding. The average Sherwood number has a minimum value at 12.deg.-13.deg., and a maximum value at a=20.deg.-25.deg. A comparison of present mass transfer measurement with other heat transfer measurements, using the heat/mass transfer analogy, shows good agreement in average transfer rates, same trend but notable differences in local values. Therefore, naphthalene sublimation technique can be adopted to explore heat transfer processes in the complex flow situations, which is considered to be hardly possible with the conventional heat transfer measurements.

• Journal of Mechanical Science and Technology
• /
• v.18 no.7
• /
• pp.1258-1266
• /
• 2004

It is important to completely understand heat/mass transfer from a flat plate because it is a basic element of heat/mass transfer. In the present study, local heat/mass transfer coefficient is obtained for two flow conditions to investigate the effect of boundary layer using the naphthalene sublimation technique. Obtained local heat/mass transfer coefficient is converted to dimensionless parameters such as Sherwood number, Stanton number and Colburn j-factor. These also are compared with correlations of laminar and turbulent heat/mass transfer from a flat plate. According to experimental results, local Sherwood number and local Stanton number are in much better agreement with the correlation of turbulent region rather than laminar region, which means analogy between heat/mass transfer and momentum transfer is more suitable for turbulent boundary layer. But average Sherwood number and average Colburn j-factor representing analogy between heat/mass transfer and momentum transfer are consistent with the correlation of laminar boundary layer as well as turbulent boundary layer.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.26 no.8
• /
• pp.1077-1087
• /
• 2002

The heat (mass) transfer characteristics on the blade surface of a high-turning first-stage turbine rotor for power generation has been investigated by employing the naphthalene sublimation technique. A four-axis profile measurement system is developed successfully for the measurements of local sublimation depth on the curved surface In the leading edge region, there is a good agreement between the present heat (mass) transfer data and the previous result on a turbine blade with a moderate turning angle, but some discrepancies are found in the mid-chord heat (mass) transfer between the two results. The local heat (mass) transfer on the present suction surface is greatly enhanced due to an earlier boundary transition, compared with that on a turbine blade with a moderate turning angle, meanwhile there is only a slight change in the pressure-side heat (mass) transfer between the two different turbine rotors. In general, the heat (mass) transfer augmentation by the endwall vortices is found much higher on the suction surface than on the pressure surface.

• Textile Coloration and Finishing
• /
• v.32 no.3
• /
• pp.135-141
• /
• 2020

The primary and secondary alcohols in cellulose reacted with acrylonitrile(AN) in the presence of strong alkalis to form cyanoethylated cellulose. The partially cyanoethylated cotton(CEC) fabric with AN in the presence of aqueous sodium hydroxide solution was described, including effects of treatment time and reagent concentrations. The weight increases of cotton fabric were shown to be linearly related to the treatment time, temperature and concentration of sodium hydroxide. The physical properties such as shrinkage ratio and tensile strength were proportional to the weight increases without significant impact on elongation. But the moisture regain decreased with decreasing hydrophilicity. The degree of substitution(DS) and transfer ratio were linearly related to the weight increases. In the CEC with increasing weight up to 24.9%, it has been obtained with DS up to 0.63-0.67 cyanoethyl groups per anhydroglucose and transferring ratio up to 87.7%. The color fastness to washing by sublimation transfer printing was improved by the cyanoethylation.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.25 no.3
• /
• pp.356-365
• /
• 2001

Heat (mass) transfer characteristics have been investigated on the endwall of a large-scale linear turbine cascade. Its profile is based on the mid-span of the first-stage rotor blade in a industrial gas turbine. By using the naphthalene sublimation technique, local heat (mass) transfer coefficients are measured for two different free-stream turbulence intensities of 1.3% and 4.7%. The results show that local heat (mass) transfer Stanton number is widely varied on the endwall, and its distribution depends strongly on the three-dimensional vortical flows such as horseshoe vortices, passage vortex, and corner vortices. From this experiment, severe heat loads are found on the endwall near the blade suction side as well as near the leading and trailing edges of the blade. In addition, the effect of the free-stream turbulence on the heat (mass) transfer is also discussed in detail.

• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.1447-1452
• /
• 2003

Vortex is very interesting flow phenomena on the heat transfer enhancement. In the present study, naphthalene sublimation technique is used to determine the average and local mass transfer coefficients on the flat plate with vortex generator. A parametric study with Reynolds number and angle of attack is carried out to investigate the heat transfer enhancement. The heat transfer coefficients on the flat plate with rectangular type and delta type vortex generator are compared with those of the flat plate without the vortex generator. Comparing heat transfer coefficients between rectangular type and delta type vortex generator, rectangular type vortex generator has much higher value than delta type vortex generator at the same condition.

• Proceedings of the SAREK Conference
• /
• 2007.11a
• /
• pp.185-190
• /
• 2007

For the successful design of heat exchangers, it is very important to understand local heat transfer characteristics on the circular cylinder of the cross flow heat exchangers. In this study, the heat exchanger using screen is developed to enhance heat transfer. The naphthalene sublimation technique is employed to measure the local heat transfer coefficients in the heat exchanger. The experiments are performed for single circular tube, in-line array tube bank with and without heat transfer promoter. Local Nusselt numbers of single circular tube and tube bank with heat transfer promoter are investigated and compared to those of without heat transfer promoter.