• Transactions of Materials Processing
• /
• v.15 no.4 s.85
• /
• pp.289-294
• /
• 2006

To reduce automobile parts weight, TWB(tailored welded blank) forming is widely used in panel forming. But products used TWB forming process have many defect, wrinkle, crack and springback. So study of TWB forming process character is very important. In this study one of the current problems of TWB forming was analyzed, especially for the try-out process of inner door panel without frame. A comparison was made between actual measurements and prediction of forming analysis for formability and springback. Also a new analysis die model which have additional plane on die surface was proposed to correct result of forming analysis. This proposed method overcomes the difference for TWB forming result between try-out and analysis.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2004.10a
• /
• pp.132-137
• /
• 2004

In order to reduce automobile parts weight, TWB(Tailored welded blank) forming is widely used in the forming of car panel, such as door inner, side outer panels. In this study, one of the current problems of TWB forming was analyzed, especially for the try-out process of TWB door inner panel without frame. A comparison was made between actual panel measurements and results of forming analysis for formability and springback.

• Journal of the Korean Society for Heat Treatment
• /
• v.23 no.4
• /
• pp.183-190
• /
• 2010

There are many methods to reduce the weight and the cost of the automobile body, among them, Tailor Welded Blank (TWB) is new welding method applied to body structure. It is necessary to evaluate mechanical properties of TWB structures or sheets for the application to automobile body parts. In this study, the stiffness of T-type and L-type joint structures, composite of TWB panel, which simplified two portions of side structure in automobile body were investigated. Additionally, the fatigue properties of TWB panels were obtained. Two types of welding technologies, laser and mash seam welding, were used to join mild panels with different thickness. This results are compared with conventional structures. The results are as follows: 1) The stiffness of joint structures, composite of TWB panel, is approximately 17% higher than that of conventional ones. 2) The location of welding line in TWB had a effect on the in plane bending stiffness, but not on the out of plane bending stiffness. 3) In terms of welding technology type, the mash seam welding show higher stiffness than the laser welding for in plane bending stiffness. But minimal differences in both types are revealed for out of plane bending stiffness. 4) The fatigue strength, composite of TWB panel, is lower than that of base steel. It is thought that defects in the welding zone had the action of notch in the fatigue test.

• Journal of the Korean Society of Safety
• /
• v.15 no.2
• /
• pp.22-30
• /
• 2000

The sub-frame of passenger car begins to be used widely for the safety of passengers. Conventional design of the sub-frame comprises 22parts, and it requires quite complicated production processes. In this papers, the sub-frame is designed with TWB(Tailor Welded Blanks) to improve stiffness, to reduce weight and to simplify the manufacturing process. To design the proper structure, structural analysis and crash analysis are executed about the conventional design and TWB applied design. A prototype TWB applied sub-frame is manufactured using mash-seam welded TB(Tailored Blanks). Comparing with the conventional sub-frame, the TWB applied sub-frame has 30% weight reduction and 17% increasement of structural stiffness in average.

• Journal of Welding and Joining
• /
• v.31 no.2
• /
• pp.30-36
• /
• 2013

Recently the use of ultra high strength steels(UHSS) in structural and safety component is rapidly increasing in the automotive industry. Furthermore, it commonly use in tailor welded blank laser welding process before hot stamping to reduce lightweight vehicle. However TWB process is to be a problem about welded strength after hot stamping because it's welded before heat treatment. Therefore, in this study, laser welds of TWB after heat treatment were analyzed for changes in the characteristics, especially the impact on the oxidation and decarburization in order to prevent pre-coated Al-Si layer welds on the properties for intensive investigation. As a result, the degradation of the TWB weldments changes in the heat treatment conditions alone, without any pre-treatment of the coating layer has confirmed that there is a limitation on the improvement. Furthermore Al-Si elements are overall distributed on the weldment and it specially concentrated along the fusion line. Hardness value of Al-Si segregation area is less than 350Hv and tensile strength showed just 78~83% compared with substrate. Accordingly, we proved that both side Al-Si coating should be removed in order to ensure the strength of the substrate.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.36 no.8
• /
• pp.857-863
• /
• 2012

In this study, tailor-welded blanks(TWB) were formed between high-strength steel(SABC1470) and cold rolled steels(SPFH590 and SPFC980) to improve passenger safety and reduce the weight of cars. Multi-material TWB specimens were highly strengthened through the heat treatment of SABC1470. The change in tensile strength caused by the stand-by time until water cooling after stamping and the deformation behavior of high-speed bending in a statically indeterminate condition such as in the center-pillar were evaluated. Multi-material TWB specimens that were heat-treated at the same temperature tended to show a decrease in tensile and yield strength, depending on the stand-by time until water cooling. On the other hand, Multi-material TWB specimens(SABC1470+SPFH590) that were heat treated at $850^{\circ}C$ showed good properties that were suitable for ensuring passenger safety in car accidents. From the viewpoint of passenger safety, it is best to use SABC1470 and SPFH590 in the upper and lower area of the center-pillar, respectively.

• Proceedings of the KSME Conference
• /
• 2007.05a
• /
• pp.1312-1316
• /
• 2007

Strip casted and rolled magnesium sheet is become exiting material for car manufacturer, due to its better formability and specific strength compare with conventional extruded sheet. TWB technology was attractive for car body designer, because it saves the weight of the car without strength loss. In this study, the laser welding performance of magnesium sheet was investigated for Mg TWB panel manufacturing. The material was strip casted and rolled magnesium alloy sheet contains 3 wt% Al and 1 wt% Zn (AZ31). Lamp pumped Nd:YAG laser of 2kW was used and its laser light was delivered by optical fiber of 0.6mm core diameter to material surface with focusing optics of 200mm focal length for TWB welding. The microstructure of weld bead was investigated to check internal defects such as inclusion, porosity and cracks. Also mechanical properties and formability were evaluated for press forming of car body. For the results, there was no crack but inclusion or porosity on weld at some conditions.The tensile strength of weld was over 95% of base metal. Inner and outer panel of engine hood were press formed and assembled at elevated temperature.

• Proceedings of the KWS Conference
• /
• 2009.11a
• /
• pp.50-50
• /
• 2009

본 연구에서는 차체 부품의 경량소재 대체에 따른 Panel Assembly Rear Seat Back 부품 제작에 최신 저입열 미그용접공정을 적용한 TWB(Tailor Welded Blank) 공정기술을 확보하기 위해 최적 용접조건 도출에 관한 연구를 진행하였다. 용접 후 성형이 이뤄지는 제조공정의 특성 상 성형강도에 중점을 둔 실험을 진행하였으며, 이를 위해 각 와이어에 따른 용접부의 기계/금속학적 특성이 평가되었다. 대상 시편은 6천계열 열처리형 합금이며, 두께는 각각 1.6t, 1.4t로 이를 맞대기 용접 후 그 특성을 평가하였다. 용접은 저입열 GMA용접 공법 중 하나인 CMT 용접법(Cold Metal Transfer)을 사용하였으며, 평가 대상 와이어로는 4043, 4047, 5183 및 5356이 사용되었다. 특성평가는 마크로 및 마이크로 조직, 경도, 인장강도, 기공 및 결함, 성형강도 등에 대해 이뤄졌으며, 희석된 와이어의 조성이 용접부 특성에 미치는 영향에 대해서도 검토되었다. 실험 결과, 5천계열 와이어가 성형강도에 비교적 더 강인한 결과를 나타냈으며 성형강도는 용접조건 및 초기 갭에 대한 영향은 받았으나, 비드형상과 강도간의 연관성은 찾을 수 없었다. 이에 따라 TWB 적용을 위한 와이어로는 5356이 가장 우수한 것으로 판명되었다.

• Korean Journal of Metals and Materials
• /
• v.50 no.3
• /
• pp.224-232
• /
• 2012

In this study, the effect of hot-stamping heat treatment on the microstructure and hardness of TWB(Tailor Welded Blank) laser joints in Al-Si-coated boron steel and Zn-coated DP(Dual Phase)590 steel was investigated. In the TWB joints without heat treatment, hardness profiles showed local hardness deviation near the fusion zone. However, there was no hardness deviation in the heat treated specimen and its hardness was higher than that of the one without the heat treatment, due to a fully martensite microstructure. In the TWB joints of both the boron and DP steels, the maximum hardnesses were observed at the HAZ(Heat Affected Zone) near the base metal, and the hardness decreased gradually to the base metal. In the heat treated joints, the hardnesses of the HAZ and the base metal of the boron steel side were similar to the maximum hardness of the weld, while those of the HAZ and the base metal of the DP steel side were higher than the maximum hardness.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1998.03a
• /
• pp.40-44
• /
• 1998

In this study, the subframe of passenger car is developed by typical analysis and carsh simulations. According this results, energy absorption and barrier froce is very important to control passenger safety and deformation shape. For that purpose, it is most effective to absorb energy more tailor welded blanks(TWB) subframe than non-TWB. The subframe with TWB is simulated, in which reduced stamping parts, weight reduction and cost down.