• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2003년도 춘계학술대회 논문집
• /
• pp.50-55
• /
• 2003

Atomic force microscope(AFM) techniques are increasingly used for tribological studies of engineering surfaces at scales ranging from atomic and molecular to microscale. AFM with suitable tips is being used for nanofabrication nanomachining purposes. In this paper, machining characteristics of silicon have been investigated by nano indentation and nano scratch. Mechanisms of material removal on the microscale are studied and the Taguchi method is introduced to acquire optimum parameters for nanomachining. This work shows effectiveness of the Taguchi method in nanomachining. Also, Acoustic Emission(AE) is introduced for the monitoring of nanomachining.

• 한국정밀공학회지
• /
• 제26권6호
• /
• pp.97-105
• /
• 2009

Optimal design of a roller rail which replaces the ball rail for three-door refrigerators is presented using the finite element analysis and the Taguchi method. Stress and deformation of the roller rail for an initial design are analyzed and evaluated. Optimal design parameters are determined using the Taguchi method. The maximum stress of the optimal design is favorably reduced comparing to the initial design. It is verified through an additional analysis that the drawer on the roller rail will not be derailed even if one opens the drawer with a transverse force.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 추계학술대회 논문집
• /
• pp.155-159
• /
• 2002

This paper has studied to obtain the grinding characteristics and optimal grinding conditions of ceramics in the grinding with diamond wheel by Taguchi method. Feed rate was most important factor to the surface roughness. In the case of 4{Si_3}{N_4}$ and ${A1_2}{O_3}$, surface roughness value were small at 3m/min of feed rate. In the case of $ZrO_2$. surface roughness value was small at 4m/min of feed rate. Surface roughness have much influenced by major load for the :ii3N4 and $ZrO_2$. On the other hand, ${A1_2}{O_3}$ have more influenced by grain shedding of brittle fracture phenomenon. The major factors affecting the surface roughness and the optimum grinding conditions were obtained with minimum experiment using Taguchi method.

• 산업경영시스템학회지
• /
• 제30권2호
• /
• pp.8-14
• /
• 2007

The powder blasting process has become an important machining technique for the cost effective fabrication of micro devices. This process is similar to sand blasting, and effectively removes hard and brittle materials. A large number of investigations on the abrasive jet machining with such output parameters as material removal rate, penetration and surface roughness have been carried out and reported by various authors. To achieve higher surface roughness, to increase material removal rate and to identify the influence of blasting parameters on the output parameters, we use the taguchi method which is one of the design methods of experiments. We can select process parameters to optimize the blasting process of glass. Experimental results indicate that the taguchi method is useful as a robust design methodology for the powder blasting process.

• Journal of Welding and Joining
• /
• 제20권5호
• /
• pp.120-126
• /
• 2002

Ni-5%Al alloy powder is widely used as the bond coating powder to improve the adhesive strength between the substrate and coating. The important properties in the bond coating are the deposition efficiency and surface roughness. In this study, it was tried to optimize the plasma spray parameters to maximize the deposition efficiency and surface roughness. In the first step, spray current and hydrogen gas flow rate were optimized in order to increase the deposition efficiency. In the next step, the seven plasma spray variables were selected and optimized to improve both the deposition efficiency and surface roughness using the Taguchi experimental method. By these optimization, the deposition efficiency was improved from about 10 % at the frist time to 51.2 % by the optimization of spray current and hydrogen gas flow rate and finally to 65.2 % by the Taguchi experimental method. The average surface roughness was increased from about $12.9\mu\textrm{m}$ to $15.4\mu\textrm{m}$.

• 한국자동차공학회논문집
• /
• 제24권1호
• /
• pp.1-9
• /
• 2016

Optimum cross-sectional shape of an automotive disc brake was developed based on FEM thermal analyses and the Taguchi method. Frictional heat flux and convection heat transfer coefficients were first calculated using equations and applied to the disc to calculate accurate temperature distribution and thermal deformations under realistic braking conditions. Maximum stress was generated in an area with highest temperature under pads and near the hat of ventilated disc and vanes. The SN ratio from Taguchi method and MINITAB was applied to obtain the optimum cross-sectional design of a disc brake on the basis of thermal deformations. The optimum cross-section of a disc can reduce thermal deformation by 15.2 % compared to the initial design.

• Advances in materials Research
• /
• 제6권1호
• /
• pp.79-91
• /
• 2017

In the present work, a design of experiment (DOE) technique using Taguchi method, has been applied to optimize the properties of ODS tungsten heavy alloys(WHAs). In this work Taguchi method involves nine experiments groups for four processing parameters (compaction pressure, sintering temperature, binding material type, and oxide type) with three levels was implemented. The signal-to-noise (S/N) ratio and analysis of variance (ANOVA) were employed to obtain the optimal process parameter levels and to analyze the effect of these parameters on density, electrical conductivity, hardness and compressive strength values. The results showed that all the chosen factors have significant effects on all properties of ODS tungsten heavy alloys samples. The density, electrical conductivity and hardness increases with the increase in sintering temperature. The analysis of the verification experiments for the physical properties (density and Electrical conductivity) has shown that Taguchi parameter design can successfully verify the optimal parameters, where the difference between the predicted and the verified values of relative density and electrical conductivity is about 1.01% and 1.15% respectively.

• 산업경영시스템학회지
• /
• 제37권4호
• /
• pp.245-250
• /
• 2014

The purpose of this study is to introduce a empirical study of using Taguchi Method for the Entrepreneurial Orientation and Financial Performance. In this study, three factors of Entrepreneurial Orientation, innovation, pro-activity and risk taking, are used of the control factors and an element, period of establishment, is chosen as a noise factor. In order to carry out this research, we obtained 200 survey sheets and performed the reliability and validity analysis of the questionnaires and then the experiment was conducted by Taguchi's experimental design. To improve Financial Performance under the noise factor of period of establishment, optimal condition are as follows; the two factors of Entrepreneurial Orientation, innovation, pro-activity should be maintained to a high level. Also, other factor, risk taking should be performed as the level that the company has maintained. Through this paper, we find out that Taguchi method is applicable for analysis of questionnaire.

• 한국환경과학회지
• /
• 제30권12호
• /
• pp.983-991
• /
• 2021

The role of the distribution basin role is to apportion incoming raw water to the primary sedimentation basin as part of the water treatment process. The purpose of this study was to calculate the amount of water in the distribution basin using computational fluid dynamics (CFD) analysis and to find a way to improve any non-uniformity. We used the Taguchi method and the minitab tool as optimization methods. The results of the CFD calculation showed that the distribution flow had a deviation of 5% at the minimum inflow, 10% at the average inflow, and 22% at the maximum inflow. At maximum flow, the appropriate heights of the 7 weirs(C, D, A, B, E, F, G) were 40 mm, 20 mm, 20 mm, 0, 0, 0, and 20 mm, respectively, according to the Taguchi optimization tool. Here, the maximum deviation of the distribution amount was 9% and the standard deviation was 23.7. The appropriate heights of the 7 weirs, according to the Minitab tool, were 40 mm, 20 mm, 20 mm, 0, 0, 0, and 20 mm, respectively, for weirs C, D, A, B, E, F, and G. Therefore, the maximum deviation of the distribution amount was 8% and the standard deviation was 17.1, which was slightly improved compared to the Taguchi method.

• 한국가스학회지
• /
• 제10권2호
• /
• pp.40-46
• /
• 2006

본 논문은 다구찌 실험 설계법을 이용하여 O-링을 장착하는데 필요한 사각 그루브의 최적설계를 위해 FEM으로 최대코시응력과 최대변형률에 대하여 해석하였다. 다구찌 설계방법은 LPG 충전노즐의 내경측에 밀봉을 위해 설치하는 O-링 그루브의 설계변수를 최적화 하는데 대단히 유용하다. FEM과 함께 다구찌 설계기법을 적용하여 계산된 해석결과에 따르면, 최적화 설계치수를 단지 9번의 반복 실험법에 의해 설계변수의 치수를 최적의 조건으로 얻을 수 있다는 측면에서 간편한 최적설계 기술이다. 이것은 다구찌 설계 실험법이 사각형상의 O-링 그루브를 설계하는 간단한 방법으로 대단히 유용하다는 것이다. 다구찌 설계기법에 기초한 해석결과에 의하면, O-링 그루브의 기하학적 형상에 대한 최적치수는 h=2.5mm, d=2.74 mm, c=0.15 mm, w=3.0 mm으로 각각 요약될 수 있다. 본 연구는 공급된 LPG 가스압력이 18 $kg/cm^2$인 상태에서 밀봉성과 안전성을 고려하면 초기압축률은 8.7%로 유지하는 것이 가장 효과적이라는 사실을 제공한다.