• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.13 no.1
• /
• pp.127-134
• /
• 2014

X-Band taper slot-typed active phased array antenna is studied and designed. Through the simulated and measured performances, it is confirmed that both of active reflection coefficient and active radiation pattern of the designed phased array antenna are agreed well with those of the prototype manufactured one. From this study, the proposed antenna structure is matched to the design target of characteristics of antenna's broadband beam.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.3 s.118
• /
• pp.257-264
• /
• 2007

In this paper, we have designed and fabricated a wide-band and high gain antenna which can integrate a standard of IEEE 802.1la$(5.15\sim5.25\;GHz,\;5.25\sim5.35\;GHz,\;5.725\sim5.825\;GHz)$. We inserted a parallel dual slot into a rectangular patch to have wide-band, and we offset an element of capacitance from the slot by using coaxial probe feeding method. We also designed a converter of $\lambda_g/4$ impedance with taper type line so that wide-band impedance can be matched easily. We finally designed structure with $2\times2$ array in order to improve the antenna gain, and the final fabricated antenna could have a good return loss(Return loss$\leq$-10 dB) and a high gain(over 13 dBi) at the range of $5.01\sim5.95\;GHz(B/W\doteqdot940\;MHz)$.

• Journal of electromagnetic engineering and science
• /
• v.5 no.1
• /
• pp.14-20
• /
• 2005

In this paper, a technique is presented for broadbanding the bow-tie slot antenna fed by a CPW(coplanar waveguide). The bandwidth performance of existing bow-tie slot designs is greatly enhanced by optimizing the slot shape and properly adjusting the characteristic impedance of the coplanar waveguide feeding the slot. To connect the 50-ohm input coaxial line to the CPW feed line, a linear taper in the CPW is employed. The designed antenna shows a 3.5 $\~$ 10.0 GHz impedance bandwidth, a 3.5 $\~$ 6.0 GHz pattern bandwidth, and a 5.5 $\~$ 7.5 dBi gain over 3.5 $\~$ 6.0 GHz. Above 6.0 GHz, the antenna radiation pattern appreciably deviates from the typical dipolar pattern.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.44 no.3 s.357
• /
• pp.105-110
• /
• 2007

We have built the millimeter-wave passive imaging system with a lens and mechanical scan antenna. The lens was designed based on optical theory in order to focus millimeter-wane. A full image was taken from image points scanned by Placing antenna at the representative focal plane selectively. An integrated antenna array device for low-loss and low-noise with the array of 4 by 1, where components such as antenna, balun, MMIC, and detector were assembled on a sin91e substrate, and a fermi tapered slot antenna with high-gain and low-side lobe were used for elements of this millimeter-wave passive imaging system. Two dimensional antenna arrangement on focal plane was achieved in this imaging system.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2001.11a
• /
• pp.127-131
• /
• 2001

본 논문에서는 공진 주파수가 2 GHz 이며 크기가 작고, 광대역 특성을 갖는 Taper 형태의 급전선로를 갖는 마이크로스트립 Bow-tie 슬롯 안테나를 제안하였다. 이 구조에서는 대역폭을 향상시키기 위하여 마이크로스트립 슬롯 안테나 방사 슬롯을 변형된 bow-tie 모양으로 설계하여 기존의 Bow-tie 슬롯 안테나와 다른 구조를 제안하였고 Electromagnetic coupling를 좋게 하기 위하여 급전선로에 Taper를 첨가하여 급전기와 안테나의 정합을 이루어 광대역 특성을 갖도록 하였다.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.10 no.2
• /
• pp.386-391
• /
• 2006

In this paper, a design of V-type Linearly Tapered Slot Antenna(V-LTSA) with uniplanar microstrip-to-coplanar stripline(CPS) transitions is presented. The effect of reducing and increasing with taper width G, teper length L and opening angle are also considered at 5.8 GHz. In the result of a simulation by using CST-MWS, the return loss characteristic came very wide band about 4.3GHz, or 1.8 Octave. Proposed V-LTSA design schemes are expected to be a good antenna for microwave and millimeter-wave communcations.

• Proceedings of the IEEK Conference
• /
• 1998.10a
• /
• pp.395-398
• /
• 1998

In this paper, the design, fabrication, and experiments of linearly tapered slot antenna(LTSA) with uniplanar microstrip-to-coplanar strip(CPS) line transitions are presented. The effect of reducing and increasing with taper width G teper longth 1, and opening angle are also mesured at 10 GHz.