• Resources Recycling
• /
• v.15 no.1 s.69
• /
• pp.66-73
• /
• 2006

The effects of operation conditions, such as bed temperature, temperature rising rate, particle size, moisture content and so on, on thermo-chemical conversion of waste wood have been determined in a micro fixed bed gasifier. The samples were waste wood-chips such as pine, oak, acacia and ginkgo. The thinning timbers used as reactants in the experiments had $35wt\%$ moisture content, $0.5wt\%$ ash content and 4,550 kcal/kg heating value on a dry basis. A typical product distribution was a $40wt\%$ liquid, $20wt\%$ solid, and $40wt\%$ dry syngas. The syngas concentration was affected by operation conditions and average syngas concentration was $H_2:40vol\%,\;CO:30vol\%,\;CH_4:10vol\%$.

• Korean Chemical Engineering Research
• /
• v.61 no.1
• /
• pp.8-18
• /
• 2023

Increasing of energy demand due to the rapid growth of global population and the development of world economy has inevitably resulted in the continuously increase of fossil fuel usage in the world. However, highly dependence on fossil fuels has necessarily brought about critical environmental issues and challenges such as severe air pollutions and rapid global warming. In order to settle these environmental and energy problems, clean energy generations in the conventional combustion processes have widely adapted in the world. In particular, novel thermochemical conversion processes such as pyrolysis and gasification have rapidly been applied for generating clean energy. Fluidized bed technologies having advantages such as various fuel use, easy continuous operation, high heat and material transfer, isothermal operation, and lower operation temperature are widely adopted and used because they are suitable for thermochemical energy conversion. The latest research trends and important findings in the thermo-chemical conversion process with fluidized bed technologies are summarized in this review. Also, the need for research such as layered materials and substances to reduce fine dust (biomass, natural resource waste, etc.) was suggested. Through this, it is intended to increase interest and understanding in fluidized bed technology and to present directions for solving future challenges in fluidized bed process technology development.

• Korean Chemical Engineering Research
• /
• v.52 no.2
• /
• pp.233-239
• /
• 2014

The slagging which generated from ash deposition on furnace wall and tube in boiler reduces the heat transfer efficiency and damages to safety of boiler. The slag flow behavior in boiler is affected by melting temperature which is related to ash compositions. In this study, the behavior of slag is researched by using ash fusibility test, called TMA (Thermo-Mechanical Analysis). The technique measures the percentage shrinkage as the function of temperature, T25%, T50%, T75%, T90%. These temperatures indicate different stages of melting. Then, the effect of ash chemical compositions measured from XRF (X-ray Fluorescence Spectrometer) to ash fusion temperatures is discussed. Among the chemical compositions, refractory and fluxing influence on ash fusibility is described. High levels of refractory component and limited amount of fluxing components ($Fe_2O_3$, $K_2O$, CaO) increase overall melting temperatures. High $SiO_2/Al_2O_3$ ratio decrease high melting temperatures (T75%, T90%). Meanwhile, the presence of reasonable levels of fluxing components reduces overall melting temperature. A presence of fluxing component such as $K_2O$ and CaO is found to decrease the T25% values significantly. From this research, it is possible to make a reasonable explanation and prediction of ash fusion characteristic from analysis of TMA results and ash chemical compositions.

• Macromolecular Research
• /
• v.17 no.4
• /
• pp.221-226
• /
• 2009

The present study firstly describes the synthesis of novel, thermo-latent initiators based on xanthenyl phosphonium salts with different counter anions and phosphine moieties and secondly examines their efficiency in the bulk polymerization of glycidyl phenyl ether(GPE). The polymerization was performed with phosphonium salt initiators($I_{SbF6}$, $I_{PF6}$, $I_{AsF6}$ and $I_{BF4}$) at ambient temperature to $200^{\circ}C$ for 1 h. The order of initiator activity was $I_{SbF6}>I_{PF6}>I_{AsF6}>I_{BF4}$. To examine the effect of the phosphine moiety on the initiator activity, polymerization was carried out with $I_{SbF6}(Ph_{3}P)$ and $II_{SbF6}(Bu_{3}P)$ at ambient temperature to $170^{\circ}C$ for 1 h. The order of reactivity was $I_{SbF6}>II_{SbF6}$. In general, the conversion percentage increased with increasing polymerization temperature. The thermal stability of these salts was measured by thermo gravimetric analysis(TGA). The solubility of phosphonium salts in various organic solvents and epoxy monomers was also investigated.

• Bulletin of the Korean Chemical Society
• /
• v.32 no.4
• /
• pp.1310-1314
• /
• 2011

Sodium beta-alumina (SBA) nano-powders were synthesized by the citrate sol-gel process, and the effects of the cationic surfactant n-cetyltrimethylammonium bromide surfactant (CTAB) were investigated. The structure and morphology of the nano-powders were characterized by X-ray diffraction (XRD) and transmission electron microscope (TEM) techniques, respectively. The effects of CTAB on the citrate sol-gel process and the SBA formation were investigated by thermo gravimetric/differential thermal analysis (TG/DTA) and Fourier transform infrared spectroscopy (FTIR). The conductivity of ceramic pellets of SBA was measured by electrochemical impedance spectroscopy (EIS). The results showed that the CTAB inhibited the agglomeration of SBA powders effectively and consequently decreased the crystallization temperature of SBA, about $150^{\circ}C$ lower than that of the sample without CTAB. The measured conductivity of SBA was $1.21{\times}10^{-2}S{\cdot}cm^{-1}$ at $300^{\circ}C$.

• Korean Chemical Engineering Research
• /
• v.45 no.6
• /
• pp.604-610
• /
• 2007

Characteristics of steam gasification and combustion of naphtha tar pitch, which is the bottom product of naphtha cracking process, were investigated by using the thermo gravimetric analyzer to develop the technology for obtaining syngas by using the naphtha tar pitch as a carbon source. Friedman's and Ozawa-Flynn-Wall method were used to calculate activation energy, reaction order and frequency factor of reaction rate constant for both of steam gasification and combustion. The activation energy of combustion of naphtha tar pitch based on the fractional conversion by Friedman's method was in the range of 41.58 ~ 68.14 kJ/g-mol when the fractional conversion level was in the range of 0.2~0.6, but 183.07~191.17 kJ/g-mol when the conversion level was 0.9~1.0, respectively. In case of steam gasification of naphtha tar pitch, the activation energy was in the range of 31.87~44.87 kJ/g-mol in the relatively lower conversion level (0.2~0.6), but 70.63~87.79 kJ/g-mol in the relatively higher conversion level (0.8~0.95), respectively. Those results exhibited that the steam gasification as well as combustion would occur by means of two steps such as devolitilization followed by combustion or gasification.

• Bulletin of the Korean Chemical Society
• /
• v.35 no.12
• /
• pp.3535-3541
• /
• 2014

Bisphenol A is considered as pollutant, because it is toxic and hazardous to living organisms even at very low concentrations. Biological oxidation used for removing this organic from waste water is not suitable and consequently application of catalytic wet oxidation has been considered as one of the best options for treating bisphenol A. We have developed Fe/SBA-15, Ni/SBA-15 and Fe-Ni/SBA-15 as heterogeneous catalysts using the advanced impregnation method for oxidation of bisphenol A in water. The catalysts were characterized with physico-chemical characterization methods such as, powder X-ray diffraction (PXRD), FT-IR measurements, N2 adsorption-desorption isotherm, thermo-gravimetric analysis (TGA), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and inductively coupled plasma optical emission spectroscopy (ICP-OES) analysis. This work illustrates activity of the catalysts for heterogeneous catalytic degradation reaction revealed with excellent conversion and recyclability. The degradation products identified were not persistent pollutants. GC-MS analysis identified the products: 2,4-hexadienedioic acid, 2,4-pentadienic acid and isopropanol or acetic acid. The leachability study indicated that the catalysts release very little metals to water. Therefore, the possibility of water contamination through metal leaching was almost negligible.

• Journal of Korean Society of Water and Wastewater
• /
• v.29 no.1
• /
• pp.57-63
• /
• 2015

Recently, Korea's municipal wastewater treatment plants generated amount of wastewater sludge per day. However, ocean dumping of sewage sludge has been prohibited since 2012 by the London dumping convention and protocol and thus removal or treatment of wastewater sludge from field sites is an important issue on the ground site. The hydrothermal carbonization is one of attractive thermo-chemical method to upgrade sewage sludge to produce solid fuel with benefit method from the use of no chemical catalytic. Hydrothermal carbonization improved that the upgrading fuel properties and increased materials and energy recovery, which is conducted at temperatures ranging from 200 to $350^{\circ}C$ with a reaction time of 30 min. Hydrothermal carbonization increased the heating value though the increase of the carbon and fixed carbon content of solid fuel due to dehydration and decarboxylation reaction. Therefore, after the hydrothermal carbonization, the H/C and O/C ratios decreased because of the chemical conversion. Energy retention efficiency suggest that the optimum temperature of hydrothermal carbonization to produce more energy-rich solid fuel is approximately $200^{\circ}C$.

• Korean Chemical Engineering Research
• /
• v.52 no.1
• /
• pp.133-140
• /
• 2014

The experiment was designed to compare the char combustion kinetics of pulverized Indonesia coals commonly utilized in Korea power plants. The reaction rate of coal char has been formulated using the external and internal effectiveness factors to describe the diffusion effect quantitatively. The Random Pore Model (RPM) was used for applying internal specific surface area as a function of carbon conversion ratio. Reaction rate was obtained from reaction time using the Wire Heating Reactor (WHR) which can heat and measure the char particle temperature at the same time. BET and TGA were used to obtain physical properties such as internal specific surface area and structural parameter. Three kinds of Indonesia Sub-bituminous coals "BARAMULTI, ENERGYMAN, AGM" were used in order to derive the activation energy and pre-exponential factor. The results of this study showed that the effect of internal diffusion than that of external diffusion is the dominant as comparison of kinetics was reflected in external and internal effectiveness factors. For three kinds of coal char, finally, activation energy of intrinsic kinetics indicates 110~118 kJ/mol.

• Environmental Engineering Research
• /
• v.25 no.1
• /
• pp.18-28
• /
• 2020

In this paper the authors provide comparative evaluation of current research that used liquefaction and pyrolysis method for bio-oil production from various types of biomass. This paper review the resources of biomass, composition of biomass, properties of bio-oil from various biomass and also the utilizations of bio-oil in industry. The primary objective of this review article is to gather all recent data about production of bio-oil by using liquefaction and pyrolysis method and their yield and properties from different types of biomass from previous research. Shortage of fossil fuels as well as environmental concern has encouraged governments to focus on renewable energy resources. Biomass is regarded as an alternative to replace fossil fuels. There are several thermo-chemical conversion processes used to transform biomass into useful products, however in this review article the focus has been made on liquefaction and pyrolysis method because the liquid obtained which is known as bio-oil is the main interest in this review article. Bio-oil contains hundreds of chemical compound mainly phenol groups which make it suitable to be used as a replacement for fossil fuels.