• Journal of the Korean Society of Propulsion Engineers
• /
• v.15 no.1
• /
• pp.55-62
• /
• 2011

In this study, we tried to improve the thrust control performance through the thrust control combustion experiment of the hybrid rocket. We constructed the system which controls the oxidizer flow by combining a needle valve with a stepping motor and controlling the stepping motor drive according to the thrust control command order. Gas oxygen was used as the oxidizer for two different propellants, PE(Polyethylene), PC(Polycarbonate), respectively. To improve the slow response time and the oscillation phenomenon in the beginning stage of the thrust control combustion experiment, we measured and analyzed the change of the flow speed of the propellant pipe. The revised thrust control combustion experiment showed that the thrust was stably controlled with the margin or error from the thrust command within ${\pm}1$ N.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.49 no.8
• /
• pp.514-521
• /
• 2000

This paper presents a direct thrust control scheme for permanent magnet linear synchronous motor(PMLSM) by using digital signal processor(DSP). And a simulation method for the direct thrust control of a permanent magnet linear synchronous motor using the equivalent circuit is presented. The detent force that was obtained by cubic spline method is considered in the simulation. Thrust correction coefficient is utilized to estimate actual thrust on the direct thrust control, which considers the longitudinal end effect due to the finite core length of the permanent magnet linear synchronous motor. The motor self inductance, the initial flux linkage by the permanent magnet is calculated in advance by the finite element analysis, and then the direct control simulation is carried out. As the results, thrust, current and speed are shwon.

• Proceedings of the KSME Conference
• /
• 2007.05a
• /
• pp.1143-1148
• /
• 2007

LRE(Liquid propellant Rocket Engine) is one of the important parts to control the motion of rocket. For operation of rocket in error boundary of the set-up trajectory, it is necessarily to control the thrust of LRE according to the required thrust profile and control the mixture ratio of propellants fed into combustor for the constant mixture ratio. It is not easy to control thrust and mixture ratio of propellants since there are co-interferences among the components of LRE. In this study, the dynamic model of LRE was constructed and the dynamic characteristics were analyzed with control system as PID control and PID+Q-ILC(Iterative Learning Control with Quadratic Criterion) control. From the analysis, it could be observed that PID+Q-ILC control logic is more useful than standard PID control system for control of LRE.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2011.04a
• /
• pp.167-174
• /
• 2011

Solid propulsion systems have simple structures compared to other propulsion systems and are suitable to long-term storage. However the systems generally have limits on control of thrust levels. In this paper we suggest control algorithms for combustion chamber pressure of variable thrust solid propulsion systems using special nozzles such as pintle valve. For this we use a simple pressure change model by considering only mass conservation within the combustion chamber, design a classical algorithm and also a nonlinear controller using feedback linearization technique. Derived thrust equation and designe a thrust control model. We design the proportion-integral controller for linearizing about operating point. We also demonstrate the performance of controller model through numerical simulations.

• 제어로봇시스템학회:학술대회논문집
• /
• 2003.10a
• /
• pp.1157-1161
• /
• 2003

A novel actuator with built-in the displacement and the thrust control function is presented in this paper. This actuator is a kind of compact hydraulic cylinder system which consists of a hydraulic cylinder, a spool, a sleeve, a mechanical feedback mechanism and a stepping motor. The displacement and thrust is in proportion to the rotational angle of stepping motor by the mechanical feedback. In order to investigate characteristics of this actuator, simulation study and preliminary experiments are conducted. Through the preliminary experiment this actuator is very effective in the control for displacement and thrust. Also, it became obvious that the stability of system can be adjusted by using the restrictor with the effect of velocity feedback. Furthermore, this paper explained that a flexible compliance control could be realized by adjusting the feedback weighting in the actuator.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1995.10a
• /
• pp.610-613
• /
• 1995

In addition to propulsive force to a flying vehicle, a rocket propulsion system can provide moments ro rotatate the flying vehicle and thus provide control of the vehicle's attitude and flight path. By controlling the direction of the thrust vectors, it is possible to control a vehicle's pitch, yaw, and roll motions. In this paper, we will introduce general thrust vector control mechanisms.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.05a
• /
• pp.197-201
• /
• 2010

Precise control of oxidizer mass flow rate is important for hybrid rocket thrust control. In this study, oxidizer mass flow rate control system is developed by using stepping motor which is controlled by Labview program. Gox is used for oxidizer and PolyCarbonate, PolyEthylene, and PMMA is used for solid propellant. To suppress thrust oscillation during thrust control experiment, schematics of the experiment is analysised and revised. Results show that thrust oscillation is suppressed successfully.

• The KSFM Journal of Fluid Machinery
• /
• v.15 no.6
• /
• pp.46-50
• /
• 2012

A high-speed centrifugal pump requires more attention to the control of its axial thrust due to the high discharge pressure than a conventional industrial pump. Vanes employed toward the rear cavity of the impeller can be an effective device to control the axial thrust of the pump. The vanes disturb circumferential flow of the cavity and it can modify the axial force acting on the impeller. In this paper, three types of vanes are installed in the high-speed centrifugal pump for liquid rocket engines and the thrust of the pump is measured with an additional thrust measurement unit. According to the results, shapes of cavity vanes have effects on the axial thrust of the pump. As the height of vanes increases, the outlet pressure of the rear floating ring seal decreases which results in a decrease of the thrust. On the other hand, head of the pump is almost same regardless of cavity vanes. Also, the pressure drop of the bypass pipeline increases when vanes are removed.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.50 no.6
• /
• pp.393-400
• /
• 2022

The Divert and Attitude Control System(DACS) used in high-altitude engagements is expensive and complex. In this paper, we design a high-altitude terminal guidance and control loop of guided-missile equipped with a Thrust Vector Control(TVC) that is less expensive and simpler than DACS. The proposed system utilizes a quaternion feedback control technique to track the thrust attitude command converted from the acceleration command of true proportional navigation guidance. The performance analysis of the proposed terminal guidance and control loop is conducted through engagement simulations against ballistic targets at a high altitude.

• Proceedings of the KIEE Conference
• /
• 2004.10a
• /
• pp.9-11
• /
• 2004

This paper presents a position control system for a linear induction motor(LIM) with cage-type secondary using direct thrust control(DTC). The position controller, that combines the merits of integral-proportional(IP) speed control, is designed for the LIM. The actual position of the LIM is defected by the linear scale the resolution of 100. Thrust correction coefficient due to the end effect of the LIM is utilized in estimating actual thrust. As a result, responses of the position, speed, thrust, and flux are shown.