• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.18 no.7
• /
• pp.635-640
• /
• 2005

In this paper, we have improved a novel high tilted optically compensated bend (OCB) (HTOCB) mode by using high tilt angle that was generated by the unique baking condition on the homeotropic alignment layer. The high tilt angle of liquid crystal (LC) was generated by new alignment process that tilt angle changed homeotropic state to homeogenous state using Hot-plate equipment; we obtained about $40\~50^{\circ}$ tilt angle with negative and positive dielectric anisotropy on the homeotropic polyimide (PI), and then LC tilt angle decreased as increasing baking temperature and time. At last, we obtained about $10^{\circ}$ with positive type NLC $({\Delta}n>0)$. Also, the LC tilt angle of positive type NLC $({\Delta}n>0)$ decreased as increasing rubbing strength at the same baking temperature and time. The novel LC operating mode (HTOCB) that used the high tilt angle by the new alignment method was improved. The response time of the novel HTOCB cell was faster than that of conventional OCB cell. We suggest that the developed the novel HTOCB cell using control of tilt angle on the homeotropic surface is a promising technique for the achievement of a fast response time and a high contrast ratio.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.22 no.9
• /
• pp.635-640
• /
• 2010

This study is suggested tilt window type to be restrained solar radiation through vertical window type in buildings. The shading and aesthetical effect of buildings would be solved by installation of tilt window type. For investigate optimum an angle of tilt window and building azimuth in reference region, the distance of transmitted solar radiation is calculated. The results of calculation showed optimum an angle of tilt window is obtained $7^{\circ}$ that the distance of transmitted solar radiation is 20% of 1.5m of balcony width. In case of an tilt window angle of $7^{\circ}$, the optimum building azimuth is showed $SW15^{\circ}{\sim}SE15$.

• Journal of Advanced Navigation Technology
• /
• v.22 no.6
• /
• pp.500-506
• /
• 2018

In this paper, we considered the one-shot alignment using master inertial navigation system (MINS) and slave inertial navigation system (SINS) in the missile to find the exact posture of a missile. In order to perform one-shot alignment, the tilt angle between MINS and SINS must be obtained, which can be compensated by obtaining the tilt angle between missile round and SINS. The tilt angle was calculated by using the roll rotation of missile round, jig for rotating the missile round and interface structure to measure the horizontal state by using a horizontal angle meter were constructed. As a result of the tilt angle save (TAS) inspection, the tilt angle ${\alpha}$, ${\beta}$, ${\gamma}$ is normal range and it is possible to perform one-shot alignment by compensating this value.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.11a
• /
• pp.116-119
• /
• 2004

In this paper, we have improved a novel (ECB) mode using tilt angle in the unique condition by hot-plate equipment. The new control of tilt angle for nematic liquid crystal (NLC) with negative and positive dielectric anisotropy on the rubbed homeotropic polyimide (PI) using baking method by Hot-plate equipment was investigated. LC tilt angle decreased with increasing baking temperature and time. Especially, the low LC tilt angle of positive type NLC $({\Delta}n>0)$ on the rubbed homeotropic PI surface by increasing temperature and time was measured. The EO characteristics of the novel ECB mode using control of tilt angle on the homeotropic surface than that of conventional OCB cell can be improved. We suggest that the developed the Novel ECB cell using control of tilt angle on the homeotropic surface is a promising technique for the achievement of a fast response time and a high contrast ratio.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.05a
• /
• pp.181-184
• /
• 2005

In this paper, we have improved a novel fast response time liquid crystal operating mode using tilt angle in the unique condition by hot-plate equipment. The new control of tilt angle for nematic liquid crystal (NLC) with negative and positive dielectric anisotropy on the rubbed homeotropic polyimide (PI) using baking method by Hot-plate equipment was investigated. LC tilt angle decreased with increasing baking temperature and time. Especially, the low LC tilt angle of positive type NLC (${\Delta}n$>0) on the rubbed homeotropic PI surface by increasing temperature and time was measured. The EO characteristics of the high tilted OCB(HTOCB) mode using control of tilt angle on the homeotropic surface than that of conventional OCB cell can be improved. We suggest that the developed the HTOCB cell using control of tilt angle on the homeotropic surface is a promising technique for the achievement of a fast response time and a high contrast ratio.

• Current Photovoltaic Research
• /
• v.5 no.1
• /
• pp.38-42
• /
• 2017

PV system output is determined according to the weather conditions, the azimuth and tilt angle. Weather conditions are changing every moment and it seems to vary according to the daily, monthly, and annual basis. The azimuth and tilt angle is decided along the site conditions for the PV system installation. This paper analyzed the PV system output through the changing the weather conditions, the azimuth, and tilt angle. We compared the TMY data and analysis of the two major weather institutes which are KMA and METEONORM. PV system output trend were analyzed by changing the azimuth and tilt angle. We used simulation tool, which is named PVsyst for the entire PV system analysis.

• Journal of electromagnetic engineering and science
• /
• v.18 no.1
• /
• pp.13-19
• /
• 2018

Wireless power transfer (WPT) based on magnetic resonant coupling is a promising technology in many industrial applications. Efficiency of the WPT system usually depends on the tilt angle of the transmitter or the receiver coil. This work analyzes the effect of the tilt angle on the efficiency of the WPT system with horizontal misalignment. The mutual inductance between two coils located at arbitrary positions with tilt angles is calculated using a numerical analysis based on the Neumann formula. The efficiency of the WPT system with a tilted coil is extracted using an equivalent circuit model with extracted mutual inductance. By analyzing the results, we propose an optimal tilt angle to maximize the efficiency of the WPT system. The best angle to maximize the efficiency depends on the radii of the two coils and their relative position. The calculated efficiencies versus the tilt angle for various WPT cases, which change the radius of RX ($r_2=0.075m$, 0.1 m, 0.15 m) and the horizontal distance (y=0 m, 0.05 m, 0.1 m), are compared with the experimental results. The analytically extracted efficiencies and the extracted optimal tilt angles agree well with those of the experimental results.

• Transactions of the Society of Information Storage Systems
• /
• v.7 no.1
• /
• pp.19-24
• /
• 2011

Holographic Data Storage System, one of the next generation data storage devices, is a 2-dimensional page oriented memory system using volume holograms in writing and retrieving process. Recently photopolymer with disc type substrate was selected as a media for the Holographic Data Storage System. The disc tilt occurs when the media rotates and the external disturbance applies. The disc tilt causes the change of the angle between the reference beam and the media, the data cannot be retrieved with the right angle or other data page is retrieved. The tilt is generated in a 2-axis direction (tangential, radial). The tangential tilt direction is the same with the multiplexing plane, while the radial tilt direction is a perpendicular to the multiplexing plane. In this research we propose 2-axis tilt angle servo system. The tilt errors are measured by using external photo detector and the additional red laser. Then the tangential direction tilt is compensated by using the galvano mirror. Also the radial direction tilt is compensated by the rotating prism between the relay lens in the reference field. Finally we confirm the compensation results through the Signal to Noise Ratio(SNR) and Bit Error Rate(BER).

• Journal of Korean Physical Therapy Science
• /
• v.3 no.1
• /
• pp.855-861
• /
• 1996

The purpose of this study was to compare a pelvic tilt angle between sound side and affected side in hemiplegic patients and the changing affected pelvic posterior tilt angle was measured at intervals of 3, 6, 9 weeks after Bobath approach. The subject for the study were 10 hemiplegic patients(mean age of 54.1 years)without orthopedic disability on pelvic bone. The data were analyzed by t-test, one-way ANOVA. The results of this study were as follows. There was a significant difference in the pelvic tilt angle between sound side and affected side in hemiplegic patients. There was a significant difference in affected pelvic posterior tilt angle between pre-treatment and post-treatment(9 weeks).

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.17 no.6
• /
• pp.661-667
• /
• 2004

The control of tilt angle for nematic liquid crystal (NLC) with negative and positive dielectric anisotropy on the rubbed homeotropic polyimide (PI) using baking method by hot plate equipment was investigated. LC tilt angle decreased with increasing baking temperature and time. Especially, the low LC tilt angle of positive type NLC (Δ$\varepsilon$＞0) on the rubbed homeotropic PI surface by increasing temperature and time was measured. The tilt angle of positive type NLC(Δ$\varepsilon$＞0) is smaller than that of the negative type (Δ$\varepsilon$＞0) on rubbed PI with increasing baking temperature and time. We consider that the tilt angle of NLC is decreased due to increasing the steric interaction between horizon component of permittivity $\varepsilon$ = of NLC and the stress of polymer side chain by high temperature. As the increase of baking temperature, we obtain that AFM (atomic force microscope) image of rubbed PI surface using Hot-plate method has formed better solid micro-groove structure than oven method.