• Transactions of Materials Processing
• /
• v.8 no.5
• /
• pp.507-519
• /
• 1999

An approach using the energy method has veen proposed for the analysis of cone spinning having the complicated deformation modes mixed by shear and normal deformation. In the proposed method, the corresponding solution is found through optimization of the total energy dissipation with respect to the parameters assumed by the velocity field defined as the variation of the length in longitudinal direction. The sheet blank is divided into three layers to consider the bending effect and the energy dissipated by shear deformation is superposed to the energy consumption due to normal deformation related with the shrinking deformation is superposed to the energy consumption due to normal deformation related with the shrinking deformation of axi-symmetric sheet element for the evaluation of total deformation energy. In order to check the validity of the proposed method, the complex spinning for making the conical cup is analyzed and the computed results are compared with the experimental results. In comparison of the computed results with existing experimental results,, the good agreement is obtained for the variation of outer radius and the distribution of thickness, and it has thus been shown that the present approach is applicable to the analysis of complex spinning.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.8 no.1
• /
• pp.64-70
• /
• 2009

This study is to analyze the impact of automotive body with computer simulation. The total deformation, equivalent strain and strain and principal stress are analyzed respectively in case of front, rear and side impacts. The maximum total deformation of side impact is more than 6 times as large as that of rear impact. The maximum equivalent strain or stress of side impact is more than 4 times as large as that of rear impact. These deformation, strain and stress of front impact are a little more than those of rear impact. The maximum principal stress of side impact is more than 4.5 times as large as that of rear impact. This stress of front impact is a little more than that of rear impact.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.19 no.3
• /
• pp.321-325
• /
• 2010

This study analyzes the results with the simulation of heat transfer, structural stress, fatigue and vibration on main parts of engine. The maximum temperature is shown by $300.73^{\circ}C$ on the upper part of piston with the heat transfer. Maximum total deformation or equivalent stress is shown by 65.31mm or 21364MPa respectively at the upper plane of piston with the structural analysis inclusive of heat transfer. The minimum life is shown by the cycle less than $10^7$ at the part of crankshaft with the fatigue analysis. The frequency with the maximum amplitude of deformation is shown by 14Hz. Maximum total deformation or equivalent stress is shown respectively by 93.99mm on the upper plane of piston or 42625MPa at the part connected with crack shaft and connecting rod at 14Hz. The durability of engine design can be verified by using the analysed result of this study.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.40 no.4
• /
• pp.94-102
• /
• 1998

This paper aims at developing the prediction technique of the deformation for the embankment such as sea dike and shore protection relevant to reclamation project along the southern coast of the Korean Peninsula. Generally total deformation of a sea dike over clayey foundation are composed of immediate settlement, plastic deformation and consolidation settlement. Plastic deformation occurs when the ultimate bearing capacity is less than overburden pressure containing the stress increment due to the construction of an embankment. The reliable prediction of total settlement is very important since deformed final geometry of sea dike is directly connected for analysing the safety of the long-term slope failure and piping. During this study, plastic deformation, major part of deformation was analysed using the program developed by authors, whereas immediate settlement and consolidation settlement were predicted by Mochinaka and Sena's method and Terzaghi's 1-dimensional theory of consolidation respectively. In order to validate the prediction technique for the deformation, a case study of Koheung Bay reclamation works was carried out. A good agreement was obtained between observation and prediction, which means the applicability of the technique.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.18 no.5
• /
• pp.477-482
• /
• 2009

This study analyzes the result with dynamic simulation about deformation according to time when a car impacts bollard. These results are shown as followings. The maximum deformation is shown at the lower part of front grass in case of the impact of front or passenger seat but this deformation is shown at the lower part of rear bumper in case of double impact. The maximum equivalent stress is shown at the upper part by the side grass of driver seat at the elapsed time of 0.00075 second after impact in case of the impact of front or passenger seat but this deformation is shown at the front bonnet at the elapsed time of 0.004 second after the additional impact in case of double impact. The maximum total deformation or equivalent stress is shown nearly same in case of the impact of front or passenger seat. But the value of this deformation or equivalent stress in case of the impact of front or passenger seat is shown with 2 times or more than 17% respectively as this value in case of double impact.

• Journal of Welding and Joining
• /
• v.16 no.6
• /
• pp.104-112
• /
• 1998

In the previous study, the countermeasure for welding deformation of bracket tilt is through up through experimental inspection for total process including welding process. For completeness of systematic examination of parts having sensitivity on welding deformation, the comparison and feedback between the result through simulation of welding process and experimental data is needed. In other words, it is necessary to control welding deformation that construct the prediction system for welding deformation through comparison and tuning with experimental data. In the present study, the application of FEA on welding process of bracket tilt with susceptibility to deformation is made and deformation behavior through change of welding sequence is focused on. It is used to improve the exactness of deformation analysis that three dimensional analysis for moving heat source, activated and deactivated bead element, and volume heat flux etc.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1996.11a
• /
• pp.548-554
• /
• 1996

A new method to locate modular fixtures using an optimization technique is proposed. The optimal fixture arrangement is derived to minimize the elastic deformation of a workpiece. That is, a fixture arrangement is regarded better if it minimized the elastic deformation of the workpiece while fixing a workpart of course. In this approach, the workpiece is projected into two dimensional domain to simplify the 3-dimensional fixture arrangement problem into 2-dimensional one. Thus the problem is reduced to find the optimal positions of one horizontal clamp and three locators which minimize the total deformation of the workpiece and the design variables are the location of the contact points between the boundary of the workpiece and the 4-fixels. The Genetic Algorithm is used for the optimization by mapping each design variables to a gene of a chromosome. The fitness value is the total strain energy of the workpiece calculated by the fin element analysis.

• Proceeding of EDISON Challenge
• /
• 2015.03a
• /
• pp.207-211
• /
• 2015

In this paper, 2 kinds of models about bike frame are simulated with static structural analysis. A bike frame with diamond type is compared with another model that Down tube is eliminated from original diamond frame. About both types of models, Property of a material and conditions of restriction & load are the same. This study shows reinforcement effects of a partial frame by adding down tube and impacts generated by applying a load at the frame such as weak points & high stress parts as well as expected deformation. The structural result of this study indicates that the equivalent stress or total deformation decreases by 57.1% or 36.4%, respectively. Also stress concentration sites are leg connecting parts, front/rear wheels fixed region and Max deformation is generated from Seat tube. In conclusion, A Down tube is highly efficient as reinforcement than frame without non down tube. Furthermore, The safety rises in case of reducing top tube thickness and increasing a reinforcement at leg connecting parts or concentration regions.

• 한국공간정보시스템학회:학술대회논문집
• /
• 2004.05a
• /
• pp.230-237
• /
• 2004

In this study, equation of finite element is formulated to analyze relations of large deformation-small deformation considering geometrical nonlinear for membrane structure. Total Lagrangian Formulation(TLF) is introduced to formulate theory and equation of motion considering Triangular Constant Strain(TCS) element in finite, element analysis is formulated. Finite element program is made by equation of motion considering TLF. This study analyzed a variety of examples, so compared with the past results.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.20 no.3
• /
• pp.280-283
• /
• 2011

This study investigates the durability of car body and the safety of passenger inside car body in the case of the impact contact at passenger and car body. In case of front impact contact, maximum von Mises equivalent stress and principal stress become 3240.7MPa and 1634MPa respectively at the rear part of car body and the neck of dummy. And maximum total deformation occurred with 14.145mm at the hand of dummy. In case of side impact contact, maximum von Mises equivalent stress and principal stress become 7687.9MPa and 1690.7MPa respectively at the front part of car body and the lap of dummy. And maximum total deformation occurred with 16.414 mm at the foot of dummy. In case of rear impact contact, maximum von Mises equivalent stress and principal stress become 2366.6MPa and 1447MPa respectively at the front part of car body and the neck of dummy. And maximum total deformation occurred with 7.548mm at the rear part of car body. As the maximum von-Mises stress at side impact is shown with more than 700MPa as over two times at front or rear impact the danger of car body is increased. The great possibility of damage is shown at neck and hand of dummy with more than total displacement of 10mm.