• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.11 no.8
• /
• pp.364-373
• /
• 2001

The gear whine noise of vehicle transmission is directly correlated tilth the gear transmission error of mating gear The object of this study is to build up the synthesized countermeasure for the reduction of gear whine noire of vehicle transmission by developing the program which can be used to analyze and predict the vibrational characteristics caused by gear transmission error of mating gears of vehicle transmission. The developed mathematical models on the elements of transmission, for example, helical gear pairs, bearings and shafts are used and the modeling of the excitation forces are developed by the gear transmission error of mating gear which is defined by the amount of the elastic deformation of gear tooth & shaft and gear profile & lead errors. The mathematical system model of vehicle transmission developed by the substructure synthesis method Is also verified by the experiments.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.24 no.6
• /
• pp.470-475
• /
• 2014

In the past, transmission error(T.E.) has been identified as one of the main sources of gear whine noise, which cause serious passengers irritation at high frequency. In this study, to identify the correlation of the T.E. and gear whine noise, a T.E. measuring system was developed. By comparing the T.E. and gear whine noise level, T.E. target value which can represent the gear noise was proposed. The conclusions are followed: (I) It is possible to measure T.E. of the gear pairs (II) Similar trends are observed between T.E. and gear whine noise. (III) By observing the T.E. pattern, presence of sideband noise can be predicted. (IV) Proposed T.E. target value can be adopted to the gear manufacturing for gear noise quality management.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2014.04a
• /
• pp.348-349
• /
• 2014

In general, there has been a lot of research concerned about the gear noise known to be proportional to gear transmission error for external gears likewise spur, helical gear, and hypoid gears. But, In the case of planetary gear set, gear noise study is insufficient because of the difficulty of designing, manufacturing, and understanding of the its mechanical system. This study is aimed to develop the transmission error measurement equipment for the planetary gear sets used in the automatic transmission. By comparing the results of the transmission error and noise objectively, user could select the optimized planetary gear set which has quiet noise level before manufacturing the automatic transmission.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.24 no.7
• /
• pp.549-554
• /
• 2014

In general, there has been a lot of research concerned about the gear noise known to be proportional to gear transmission error for external gears likewise spur, helical gear, and hypoid gears. But, In the case of planetary gear set, gear noise study is insufficient because of the difficulty of designing, manufacturing, and understanding of its mechanical system. This study is aimed to develop the transmission error measurement equipment for the planetary gear sets used in the automatic transmission. By comparing the results of the transmission error and noise objectively, user could select the optimized planetary gear set which has quiet noise level before manufacturing the automatic transmission.

• Journal of the Korean Society of Safety
• /
• v.10 no.4
• /
• pp.13-21
• /
• 1995

On mini-bus with diesel engine, at idle rpm for taking measurement to reduce gear rattle noise, was tested by the three clutch disc samples by turns, then measured the fluctuation of revolution of engine & transmission and parallel vibration of differential gear & transmission. By analyzing the measured data, the gear rattle noise, the matching design and tuning technic of transmission are comprehended and established. Conclusions of this test are as follows ; (1) Fluctuation of revolution on transmission is greatly affected by torsion of clutch disc according to fluctuation of engine revolution transmit to transmission through clutch system. Especially, gear rattle noise can be reduced by minimaizing the fluctuation of the revolution of transmission using pre-damper type clutch disc. (2) The reason of gear rattle noise is higher in summer than winter and driving longer period than initial driving is due to affection by drag torque changing. So, it is necessary for manufacturer to choose proper oil to transmission. (3) It can be occurred jumping and crash noise by applying the pre-damper type clutch disc for reducing the gear rattle noise. So, it is necessary to do test with actual vehicle according to test procedure.

• Journal of the Korean Society for Precision Engineering
• /
• v.33 no.2
• /
• pp.109-114
• /
• 2016

Nowadays, lower gear vibration and noise are necessary for drivers in automotive gearbox, which means that transmission gearbox should be optimized to avoid noise annoyance and fatigue before quantity production. Transmission error (T.E.) is the excitation factor that affects the noise level known as gear whine, and is also the dominant source of noise in the gear transmission system. In this paper, the research background, the definition of T.E. and gear micro-modification were firstly presented, and then different transmission errors of loaded torques for the spur gear pair were studied and compared by a commercial software. It was determined that the optimum gear micro-modification could be applied to optimize the transmission error of the loaded gear pair. In the future, a transmission test rig which is introduced in this paper is about to be used to study the T.E. after gear micro-geometry modification. And finally, the optimized modification can be verified by B&K testing equipment in the semi-anechoic room later.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2001.05a
• /
• pp.628-632
• /
• 2001

Experimental approach was investigated to improve gear rattle noise of a small car. During the development of a small car serious problem occurred inside the transmission gear units. The transmission was a carried over system from a less powered predecessor. Several components of suspicion were investigated, and applied to reduce rattle noise. In general, backlash, the assembly gaps, and the clutch disk rattle induce gear rattle noise. Above mentioned improvements were applied to reduce the noise, but still problem remained. Meanwhile, the temperature inside the gearbox was reported to be unusually high and the life of transmission oil quality deteriorated drastically, Temperature increment caused the large gap between the bearing outer diameter and the transmission housing. Large gap made the gear shaft assembly move intermittently and impact each other. The tighter control of the assembly gap allowed the rotating shafts smoothly and reduced the gear rattle noise even in the high temperature range.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2001.05a
• /
• pp.552-558
• /
• 2001

When operating lathe gear box which is equipped with geared transmission, it sometimes generates loud noise and excessive vibrations. In order to identify their causes, in this study, torsional and lateral vibration characteristics including critical speeds of the gear transmission system are firstly analyzed using lumped parameter models. Natural frequencies and mode shapes of the gear box structure are also analyzed by using the modal test. Furthermore, measured vibration and noise signals during operations are analyzed and compared with theoretical analysis results. After all, it is concluded that the primary cause of the excessive noise and vibrations is the resonance between gear meshing frequency including its side bands, the frequencies of shaft bending and torsional vibrations, and the natural frequencies of the gear box structure. Consequently the noise and vibration levels are greatly reduced by avoiding resonance between the natural frequencies and gear meshing frequencies through the rearrangement of the gears on the transmission shaft without any gear ratio change.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.25 no.7
• /
• pp.487-495
• /
• 2015

A generalized special program called planetary transmission analysis(here in after PTA) is developed to improve planetary gear noise in automatic transmission. PTA is capable of analyzing any typical one-degree-of-freedom automatic transmission gear train containing any number of simple, compound or complex-compound planetary gear sets. The kinematics module in PTA can compute the rotational speeds of gears and carriers and calculate the order frequencies to predict the planetary noise components. The power flow analysis module performs a complete static force analysis providing forces, moments, or torques of gears, bearings, clutches and connections. Based on the given type and number of planetary gear sets, the search algorithm determines all possible kinematic configurations and gear tooth combinations in a required set of gear ratios, while eliminating whole kinematic redundancies and unfavorable clutching sequences. By using PTA program, planetary internal speeds of new developed automatic transmission are early obtained; therefore, possibility of the noise problem could be predicted in early design stage. As implementing PTA in planetary gear NVH development procedure, planetary gear noise was successfully reduced by 10 dBA.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.16 no.3
• /
• pp.54-62
• /
• 2017

When gears mesh, shock and noise are produced as results of tooth error and tooth deformation under load. Transmission error (TE) is the most important cause of gear noise and vibration because TEs affect the changes of the force and the speed of gears. Gear tooth modification research plays a positive role in reducing TE and improving the design level and transmission performance of transmission systems. In high-precision manufacturing gear, gear tooth modification is also commonly used to reduce noise in practical applications. In order to study the accuracy of gear transmission, some empirical gear profile micro-modifications are introduced, and a helical gear pair is modeled and analyzed in RomaxDesigner software to investigate the utility of these modification methods. Some of these will be selected as experimental proposals for gear pairs, and these manufactured gears will be tested and compared in a semi-anechoic room later. The final purpose of this study is to find reasonable and convenient empirical formulae to facilitate improved gear production.