• Nuclear Engineering and Technology
• /
• v.54 no.4
• /
• pp.1355-1362
• /
• 2022

Nuclear fuel, including its fresh state, must be handled safely due to its critical and hazardous nature. Under normal transport conditions, several interactions take place among different components, such as transport cask used for loading the nuclear fuel and tie-down structure to attach with the vehicle. To ensure structural integrity of the nuclear fuel, vibrations and impacts transmitted from the vehicle must be sufficiently reduced. Therefore, in this study, we conducted two transportation tests from Daejeon to Kijang in Korea to verify the vehicle-induced vibrational characteristics of the KJRR-F fresh nuclear fuel when transported under normal transport conditions. The speed and location of the vehicle were obtained via GPS, and the accelerations between the vehicle and the KJRR-F fresh nuclear fuel were measured. Additionally, using the acceleration results, a structural analysis was conducted to confirm the structural integrity of the nuclear fuel under the most severe conditions during normal transport.

• Journal of the Society of Disaster Information
• /
• v.16 no.2
• /
• pp.310-317
• /
• 2020

Purpose: In this study, the characteristics of hazardous chemical transport vehicle accidents during the last six years from 2014 to 2019 was analyzed. This study is to prevent chemical transport accidents. Method: Using statistics from the Ministry of Environment, chemical transport vehicle accidents were classified into accident type, accident cause and vehicle type. Result: Of the total 506 cases chemical accidents, 105 cases were caused by transport vehicle. More than 20 percent of total accidents were reported. Most of the accidents were caused by spill·leak. The main causes of the accident were traffic accidents(49 cases) and management negligence(29 cases). This was more than 74% of all transport vehicle accidents. By vehicle type, 57 cases(54%) were most common in tank lorries, followed by trucks (39 cases, 37%) and trailers (9 cases, 9%). Conclusion: In order to prevent accident of transport vehicle, thorough inspection of the transport vehicle is required and safe operation of the driver. In addition, the government needs to expand real-time monitoring of transport vehicles and comprehensively manage different systems by the relevant ministries.

• Proceedings of the Korean Operations and Management Science Society Conference
• /
• 2003.05a
• /
• pp.1165-1170
• /
• 2003

The objective of this study is to develop the simulation model of transport vehicle to analyze the required number of transport vehicle and to design the traffic pattern at automated container terminal. To model the transport vehicle, we defined the vehicle model and the traffic model using the state transition model of transport vehicle. An application of a simulation to simulate an automated container terminal with perpendicular layout is developed and described. From the results of simulation experiment, we obtained the vehicle speed and the number of vehicle under given productivity of container cranes, and analyzed the saving effect by cycle time.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2004.04a
• /
• pp.443-449
• /
• 2004

In this paper, we established a simulation model for transport vehicle that carries the container transportation between apron and yard block on automated container terminal with a perpendicular yard layout. Usually, the efficiency of container terminal is evaluated by productivity of container cranes at apron, and though there are enough support of transport vehicles and yard cranes, can improve the productivity of container cranes. Especially, transport vehicle is very important factor in productivity of container cranes and has variable work productivity according to loading and unloading situation of container cranes. Therefore, a method that can estimate work productivity of transport vehicle efficiently is required. We analyzed work productivity of transport vehicle using simulation model that has state transition of transport vehicle. We performed various simulation experiment and analyzed work productivity of transport vehicle and calculated the required number of transport vehicle by container crane additionally.

• Journal of Korean Society of Transportation
• /
• v.34 no.6
• /
• pp.510-522
• /
• 2016

In studies involving public transport, social welfare improvement is simply explained by the increase in public transport demand. However, the increase in the demand for public transport is mostly observed by the change in the frequency of public transport service, and in-vehicle crowding in public transport has not been an object of concern. This study examines and tries to reveal the cause of the changes of the social welfare and in-vehicle crowding of the changing public transport from imposing congestion pricing. We observe that congestion pricing increases in-vehicle crowding in public transport. This predictable phenomenon is more exacerbated in case of not operating bus-only lane. It should be noted that in-vehicle crowding is more increased in suburban, but in First-best toll system it tends to get worse less than it in other congestion pricing systems. We identify that the change of in-vehicle crowding is affected by the change of proximity of the housing to workplace, the number of commuting trips, and unpredictable distortion effect of the congestion charge.

• Journal of Navigation and Port Research
• /
• v.30 no.8 s.114
• /
• pp.691-697
• /
• 2006

The objective of this study is to develop the alternative model of the container transport vehicle of high productivity for the purpose of the increase of terminal productivity. In order to develop the alternatives, we analyze the technical specification of existing transport vehicles such as YT(Yard Tractor), S/C(Straddle Carrier), SHC(Shuttle Carrier), and AGV(Automated Guided Vehicle) and investigate the operation and performance of transport vehicles to classify the technical generation. The development alternative of transport vehicle presented in this study will usefully be apply to advanced container terminal with higher productivity in near future.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2006.06b
• /
• pp.367-372
• /
• 2006

The objective of this study is to develop the alternative of the container transport vehicle of new type for the purpose of the increase of terminal productivity. In order to develop the alternatives, we analyze the technical specification of existing transport vehicles such as YT(Yard Trailer), S/C(Straddle Carrier), SHC(Shuttle Carrier), AGV(Automated Guided Vehicle) and investigate the operation and performance of transport vehicles to classify the technical generation. The development alternative of transport vehicle is presented in this study is very useful to advanced container terminal with higher productivity.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.28 no.1
• /
• pp.55-63
• /
• 2005

This paper is to analyze the travel distance and the transport size of the vehicle when the AGV carries multiple-load in the tandem automated guided vehicle systems. The size of multiple-load represents the number of load that the AGV can carry simultaneously. The AGV can carry simultaneously multiple-load that load types are different. The transport system of the manufacturing system is a tandem configuration automated guided vehicle system, which is based on the partitioning of all the stations into several non-overlapping single closed loops. Each loop divided has only one vehicle traveling unidirectionally around it. The AGV of each loop has to have sufficient transport capacity that can carry all loads for given unit time. In this paper, the average loaded travel distance and the size of feasible multiple-load of the vehicle are analyzed. A numerical example is shown.

• Journal of Mechanical Science and Technology
• /
• v.16 no.9
• /
• pp.1175-1182
• /
• 2002

The commercial viability of heat exchanger is mainly dependent on its long-term fouling characteristic because the fouling increases the pressure loss and degrades the thermal performance of a heat exchanger. An experimental study was performed to investigate the characteristics of fluid flow and heat transfer in a fluidized bed heat exchanger with circulating various solid particles. The present work showed that the higher densities of particles had higher drag force coefficients, and the increases in heat transfer were in the order of sand, copper, steel, aluminum, and glass below Reynolds number of 5,000.

• 한국ITS학회:학술대회논문집
• /
• 2010.05a
• /
• pp.53-55
• /
• 2010