• Journal of the Korean Geosynthetics Society
• /
• v.6 no.4
• /
• pp.29-37
• /
• 2007

Reduction Factor for Installation Damage required for calculation of design strength of geogrid used in MSEW(mechanically stabilized earth wall) design is usually obtained in the field test simulating real construction condition. However, damages occurred in geogrid during backfill work are influenced by many factors such as polymer types, unit weight per area, backfill construction method and gradation of backfill material and field test considering these factors demands lots of time and costs. In this study, factors affecting installation damage are analyzed and empirical method for evaluating reduction factor for installation damage using maximum particle size in backfill material is suggested.

• Journal of Magnetics
• /
• v.22 no.1
• /
• pp.162-167
• /
• 2017

Magnetic spiral-type microrobots, which are driven by a rotating magnetic field, have excellent locomotive abilities, whereas their medical applications are limited in the terms of function, such as the ability to drill in blood vessels. In this study, we propose a new robot with superior applications using a magnetic spiral-type machine. The proposed robot can be applied to stent transportation and installation without a catheter. In particular, the robot can be applied to the cardiovascular system, cerebrovascular disease, and nonvascular stent applications depending on the robot size. The robot consists of two independent spiral-type machines and four magnets in total. We controlled directions of thrust force of the two machines, respectively, for active locomotion with a task. We conducted a preliminary validation of the proposed robot for stent transportation and installation through experimental analyses.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.14 no.2
• /
• pp.14-23
• /
• 2015

This study was intended to evaluate the feasibility of the vehicle detector using a coil sensor. For the evaluation, the research team built a test environment for the detector consisting of a oscillation circuit, data collecting circuit, data monitoring and saving circuit, etc. As the result of the frequency analysis of the detector from the test environment, it was verified for the detector using a coil sensor to generate stable frequencies. In addition, the ease of construction and management was tested by comparing the size of cutting areas, consumption of installation materials, and installation time for a traditional loop detector and the detector using a coil sensor. As a result, the installation of the detector using a coil sensor requires less size of cutting areas, consumption of installation materials, and installation time.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.23 no.8
• /
• pp.124-129
• /
• 2009

Recently, there has been a growing global interest in environmental conservation, and the field of electric power equipment has been working to become more environment-friendly. Accordingly the 154[kV] low noise transformer is developed through the research. The low noise transformer decreases the audible noise level but the low noise transformer has several changes in the increase of weight and volume and the application of rubber damper. Therefore it is necessary to inspect the test, transportation, installation and operation about field application. In this paper, we investigate the standards of the audible noise level, the weight and volume of the transportation, the installation space and operation in order for effective field application.

• Journal of Korean Society of Transportation
• /
• v.3 no.1
• /
• pp.76-85
• /
• 1985

The significant role of transportation system for economic development process has been recognized, but the argument that transportation improvements stimulate economic development has brought sometimes no resonance in lacking of a plausible theory on the conditions and process of economic development by transportation investment. This paper reviews the theory on regional differentiation of transportation system and shows why and how the installation of a new transportation system or the improvements of the old transportation quality differentiate the spatial order of economic activities. It presents the interaction between the change of transportation quality with introducing of definition "transportation value" as tool of its determination and economic activities following the regional differentiation process, which result means regional defferentiation of niveau of economic development.

• Journal of Korean Society of Transportation
• /
• v.12 no.1
• /
• pp.137-149
• /
• 1994

The objective of study is to evaluate the effect of speed control hump on traffic operation and accidents. Three sites were investigated for the change of traffic accidents before and after the hump installation. Vehicle speeds approaching the hump were also analyzed. The study revealed that not only the number of traffic accidents but also the accident severity were significantly reduced by the installation of hump. Further, different types of traffic accidents with lower severity were observed after the hump installation. For the effect of speed reduction by hump, it was found that the speeds observed at 15m upstream of hump were in the range of 36~50 percent of approaching speeds which were not affected by (ie, without) the hump. Economic analysis of hump installation showed the benefit-cost ratio of 4.3 and 11.2 at two sites. Further analysis revealed that the benefit by the accident reduction exceeds the cost by speed reduction and installation capital if AADT is below 43,150 vehicles on two lane highways. It is recommended from the study that humps should be considered on two lane highways of high accident locations for excessive speeds to reduce traffic accidents and severity.

• Journal of the Korean Society of Safety
• /
• v.32 no.4
• /
• pp.129-136
• /
• 2017

This study investigated the probability of possible accident through qualitative and quantitative analysis of the pressure safety valve types installed in facilities using high pressure gas to compare the installation domestic and foreign pressure safety valve standards sought the safety characteristics and safety improvement direction accordingly. The three types are the case where the shut-off valve is not installed at the front of the PSV (Case A), If a shut-off valve is installed at the front of the PSV for inspection (Case B) and If a shut-off valve is installed in front of PSV (C.S.O), PSV is installed in parallel (Case C). Three types of cases were compared with FTA and HAZOP. The results of study of the possible accidents due to over-pressure safety valve installation type, used in a high-pressure gas facilities was shows in the following order Case B > Case A > Case C. The results of analysis through FTA was in order to protect the reservoir for the possible occurring of accident the safety valve installation is depend on its type. In the FTA analysis, defects in the device itself which attached to the storage tank as a substitute for analysis of the probability of operator mistakes was Case B with as high as $2.01{\times}10^{-6}$. Depending on the type of installation analysis of Case B in order to ensure safety is prohibited to install shut-off valve and believes that mandatory regulations are needed. Rationally installing of pressure safety valve in the high pressure using facilities will be expected to improve the industrial safety from severe accidents such as high-pressure gas fire explosion.

• Journal of the Korean Society of Industry Convergence
• /
• v.22 no.5
• /
• pp.519-527
• /
• 2019

This study was conducted to present useful information on the utilization and productivity analysis of laminated modular multi-family housing. To this end, the process of site installation was investigated and analyzed through a prior study, and the monitoring survey was conducted through the site installation case of an stacked multi-family housing. Based on the above, the results of productivity analysis using the web-cyclone technique were also presented. However, the site installation process has limitations on generalisation because the process is not the same for each construction company, and also limits that require verification through application in the actual site of the web-cyclone model presented in this study.

• Journal of Korean Society of Transportation
• /
• v.32 no.5
• /
• pp.421-430
• /
• 2014

The greenhouse gas emission generated by idling vehicles is a critical issue in the greenhouse gas reduction from the transportation sector. Recently, the mandatory application of the Idle Stop and Go (ISG) for buses, trucks and taxis is in the process of legislation. Focusing on the regulation is about to apply to passenger cars, this study analyzed the quantitative economic effects of the ISG installation by passenger car types in Seoul metropolitan area to support proper policy making. The benefit cost ratio of ISG installation on commercial passenger car of Seoul is the most effective, calculated as 8.55. Accordingly, the amount of 660 liters (per year per vehicle) of fuel and 1,606 kg (per year per vehicle) of $CO_2$ could be reduced. The results of this study might be used as an index for judgment of policy such as determining appropriate subsidy for ISG installation on passenger cars.

• Proceedings of the KIEE Conference
• /
• 2015.07a
• /
• pp.1611-1612
• /
• 2015

This research paper is to analyze the specific situation for the 157 failure cases of Seoul Metro power cable since 1990 and to consider the countermeasures. This is, also, to prevent accidents by analyzing the current state of each Line, the failure of causes, railroad tracks, installation year, opening year, and monthly failure conditions and by presenting the countermeasures. In addition, this research is to discuss the present installation situation of Seoul Metro power cable, the types of power cable, symptoms, causes and the countermeasures.