• The Transactions of the Korean Institute of Power Electronics
• /
• v.13 no.1
• /
• pp.63-69
• /
• 2008

The position of stator is essential when a trapezoidal BLDC motor is drived. In this paper we proposed a novel sensorless drive system for the trapezoidal BLDC motor without hall sensors or encoders. The resistor Y-connecting method is used to obtain Back-emf of a trapezoidal BLDC motor. Especially, by using the new Back-emf filter circuit proposed in this paper the sensorless characteristic in low speed is improved. The prototype proposed system applied for a 100[W] rating BLDC motor is made and the propriety of the Back-EMF filter circuit is also verified.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.6 no.4
• /
• pp.582-588
• /
• 2002

This paper presents a efficient sensorless driving strategy for brushless dc motor(BLDCM). By varying PWM switching frequency(4KHz, 6KHz, 8KHz) properly according to the rotating speed, the improvement of the efficiency and the operating characteristics through the wide speed are obtained.. The experimental results show that the proposed method can efficiently improve the sensorless driving performance for BLDCM with trapezoidal back emf.

• Journal of Magnetics
• /
• v.21 no.2
• /
• pp.173-178
• /
• 2016

Six-step commutation control widely used in brushless DC (BLDC) motor can be applied to consequent pole permanent magnet (CPPM) belt starter generator (BSG) with trapezoidal back electromotive force (EMF) in the starter state. However, rotor position detection with three Hall sensors in BLDC motor can hardly be employed in CPPM BSG due to asymmetric flux distribution in each pole side of CPPM BSG. This paper presents a low-cost rotor position detection method for CPPM BSG in which six Hall sensors are proposed to be used based on the analysis of flux distribution by 3D FEA. In the method, the six Hall sensors are divided into three groups and two signals in each group are combined through performing logic operations. In addition, offset angle between back EMF and the related Hall signal can be compensated by moving the Hall sensors. Experiments of a 2 kW CPPM BSG prototype have also been performed to verify the proposed method.

• Proceedings of the KIEE Conference
• /
• 2000.07b
• /
• pp.1108-1110
• /
• 2000

The BLDCM(Brushless DC motor) has been the Trapezoidal Back Electromotive Force(EMF) due to a surface magnet rotor with nonlinear distribution and full-pitch windings. Theoretically, it should be fed with rectangular phase current in order to minimize torque ripple. But, because voltage source inverter drives BLDCM, perfectly rectangular phase currents are not available. Now in this paper, using fourier series coefficients, calculating the coefficients of harmonic current within available orders and each harmonic component are controlled on stationary frame. Only using four switches, low cost and small size drive can be made and proposed method will be more useful in industrial. Simulation and experimental results prove the validity of the proposed method.

• Proceedings of the KIEE Conference
• /
• 1994.07a
• /
• pp.475-478
• /
• 1994

In this paper two methods of torque control for brushless DC motor with non-ideal trapezoidal back EMF are presented. One is the method of modulating the reference current so as to give a constant torque since the torque is given by the back EMF and the. phase currents. And the current control loop includes the feedforward control of back EMF and of the neutral voltage between the neutral points of the inverter and of the machine. The other is a direct voltage calculation algorithm for a given reference torque. In the two methods, the time delay due to the calculation is compensated by one sampling current prediction. The simulation results are presented to verify the proposed methods.

• International Journal of Control, Automation, and Systems
• /
• v.6 no.4
• /
• pp.477-487
• /
• 2008

This paper proposes a new position sensorless drive for brushless DC (BLDC) motors. Typical sensorless control methods such as the scheme with the back-EMF detection method show high performance only at a high speed range because the magnitude of the back-EMF is dependent upon the rotor speed. This paper presents a new solution that estimates the rotor position by using an unknown input observer over a full speed range. In the proposed method, a trapezoidal back-EMF is modelled as an unknown input and the proposed unknown input observer estimating a line-to-line back-EMF in real time makes it possible to detect the rotor position. In particular, this observer has high performance at a low speed range in that the information of a rotor position is calculated independently of the rotor speed without an additional circuit or complicated operation process. Simulations and experiments have been carried out for the verification of the proposed control scheme.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.6 no.3
• /
• pp.223-230
• /
• 2001

This power proposes a new sensorless drive system for the trapezoidal brushless DC motor generally requiring mechanical position or speed sensor. For this an indirect rotor position sensing method from the back emf waveform of non-conducting phase is explained. Back emf waveform of non-conducting is obtained from analysing terminal voltage created by making Y-connection. And an experiment is implemented with a driving system which use 87c196mc microcontroller having a peripheral associated with 3-phase signals and inverter composed of Power MOSFET. The experimental results show the validity and practicality of the proposed sensorless drive.

• Journal of Power Electronics
• /
• v.18 no.5
• /
• pp.1424-1433
• /
• 2018

This paper presents a novel space vector pulse-width modulation (SVPWM) to synthesize an arbitrary non-sinusoidal phase voltage. The key of the proposed method is that the switching vectors used to comprise the reference vectors in the ${\alpha}_1-{\beta}_1$ frame and the ${\alpha}_3-{\beta}_3$ frame are decoupled. In the ${\alpha}_1-{\beta}_1$ frame, the reference vector is comprised by near two large vectors. The corresponding vector comprised by the two vectors in the ${\alpha}_3-{\beta}_3$ frame is considered as a disturbance, which is restrained by close-loop control. In the ${\alpha}_3-{\beta}_3$ frame, there are two methods to comprise the reference vector. Method I is a near two middle vectors method. Method II uses near four vectors (two middle and two little vectors). The proposed SVPWM using decoupled switching vectors can guarantee a maximum modulation index in the ${\alpha}_1-{\beta}_1$ frame. The effectiveness of the proposed method is verified by simulated and experimental results under various operation conditions.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.8 no.1
• /
• pp.56-63
• /
• 2003

This paper studies that torque model considered with decaying phase back-EMF is different In conduction and commutation period and analyzes the torque pulsation components mathematically. In this paper, it is proposed a novel method to suppress torque pulsation due to commutation time. First, it propose commutation delay time control method, which is to compensate current slope of rising phase and decaying phase to control commutation time. Current ripple is minimized at non-commutating current and torque ripple is reduced below critical speed range that dc link voltage is the same as four times of back-EMF voltage. However, torque ripple still exists due to the relation with back-EMF and commutating current and it is increased on a large scale above critical speed range, especially. Secondly, proposed method is commutation time control, which is considered with torque pulsation due to the relation of back-EMF and commutating current. Through the proposed method, the torque pulsation can be minimized in the whole speed range as well as range over critical speed.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.12 no.2
• /
• pp.157-164
• /
• 2007

In this paper, a novel sensorless drive for brushless DC (BLDC) motor using the fuzzy back-EMF observer is proposed to improve the performance of conventional sensorless drive methods. Existing sensorless drive methods of the BLDC motor have low performance at transients or low speed range and occasionally require additional circuits. To cope with these problems, the back-EMF of the BLDC motor must be precisely estimated by a fuzzy logic, which is suitable to estimate the back-EMF which has a trapezoidal shape. The proposed algorithm using fuzzy back-EMF observer can achieve robust control for the change of an external condition and continuously estimate position of the rotor at transients as well as at steady state. The superiority of the proposed algorithm is proved through the simulation compared with other sensorless drive methods.