• Wind and Structures
• /
• v.31 no.4
• /
• pp.287-298
• /
• 2020

This paper presents an experimental investigation on the surface pressures on the CAARC standard tall building model concerning the effects of freestream turbulence. Two groups of incidence turbulence are generated in the wind tunnel experiment. The first group has an approximately constant turbulence intensity of 10.3% but different turbulence integral scale varying from 0.141 m to 0.599 m or from 0.93 to 5.88 in terms of scale ratio (turbulence integral scale to building dimension). The second group presents similar turbulence integral scale but different turbulence intensity ranging from 7.2% to 13.5%. The experimental results show that the mean pressure coefficients on about half of the axial length of the side faces near the leading edge slightly decrease as the turbulence integral scale ratio that is larger than 4.25 increases, but respond markedly to the changes in turbulence intensity. The root-mean-square (RMS) and peak pressure coefficients depend on both turbulence integral scale and intensity. The RMS pressure coefficients increase with turbulence integral scale and intensity. As the turbulence integral scale increases from 0.141 m to 0.599 m, the mean peak pressure coefficient increases by 7%, 20% and 32% at most on the windward, side faces and leeward of the building model, respectively. As the turbulence intensity increases from 7.2% to 13.5%, the mean value of peak pressure coefficient increases by 47%, 69% and 23% at most on windward, side faces and leeward, respectively. The values of cross-correlations of fluctuating pressures increase as the turbulence integral scale increases, but decrease as turbulence intensity increases in most cases.

• Journal of Mechanical Science and Technology
• /
• v.15 no.11
• /
• pp.1580-1587
• /
• 2001

In Part I, we extended the capability of the Goore Scheme for application to multi-dimensional problems and improved convergence performance. In this paper, we apply the improved Goore Scheme to th e control of turbulence for drag reduction. Direct numerical simulations combined with the control scheme are carried out to simulate a controlled turbulent channel flow at low Reynolds number. The wall blowing and suction is applied through the Goore algorithm using the total drag as feedback. An optimum distribution of the wall blowing and suction in terms of the wall-shear stresses in the spanwise and streamwise directions is sought. The best case reduces drag by more than 20 %.

• Journal of Mechanical Science and Technology
• /
• v.15 no.11
• /
• pp.1572-1579
• /
• 2001

We investigate the possibility of application of the Goore Scheme to turbulence control for drag reduction. In Part I, we examine the performance of the original Goore Scheme by applying it to a si mple one-dimensional problem. For the application of the scheme to turbulence control, we extend the scheme's capability so that it can treat multi-dimensional problems and examine its validity theoretically. The convergence of the extended scheme with a dynamic memory is faster by an order of magnitude than the original scheme. In Part II, we apply the proposed scheme to reduce drag for turbulent channel flows through direct numerical simulation.

• 한국전산유체공학회:학술대회논문집
• /
• 2003.10a
• /
• pp.35-35
• /
• 2003

• Journal of Wind Energy
• /
• v.4 no.1
• /
• pp.46-52
• /
• 2013

The wind generally includes turbulence characteristics in nature. So the yaw errors between wind turbine direction and wind direction occur due to turbulence fluctuation. The yaw errors affect the fatigue load of wind turbine system and power reduction. The components of turbulence intensity are different from those of each site where the wind turbines are installed. We studied that the fatigue load and power efficiency are improved by controlling yaw motions. In this study, we controlled the averaged yaw error time according to site conditions by turbulence intensity.

• International Journal of Aeronautical and Space Sciences
• /
• v.5 no.1
• /
• pp.30-38
• /
• 2004

This paper deals with a problem of automatic landing guidance and control ofthe longitudinal airplane motion under the wind shear turbulence. Adaptive gainscheduled PID control law is proposed in this paper. Fuzzy logic is the main part ofthe adaptive PID controller as gain scheduler. To illustrate the successful applicationof the proposed control law to the automatic landing control problem, numericalsimulation is carried out based on the longitudinal nonlinear airplane model excited bythe wind shear turbulence. The simulation results show that the automatic landingmaneuver is successfully achieved with the satisfactory performance and the gainadaptation of the control law is made adequately within the limited gains.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2004.05a
• /
• pp.452-456
• /
• 2004

A study on gust loads alleviation using aircraft control surface was performed. Aeroservoelastic model including control surface controller was formulated and validated by comparing the results of continuous turbulence response analysis with those of MSC/NASTRAN. Optimal control with output feedback was adopted for designing the control surface controller, and the effects of gust loads alleviation was validated by performing the numerical simulation for the controller designed.

• Journal of computational fluids engineering
• /
• v.2 no.2
• /
• pp.18-25
• /
• 1997

A pressure-based Navier-Stokes numerical solver was used to compare solutions of the k-ε/RNG k-ε turbulence models. An efficient grid generation scheme, the transient grid generation with full boundary control, was used to solve the flows in the tip clearance region. Results indicate that the calculations using k-ε model captures various phenomena related to the tip clearance with good accuracy.

• Wind and Structures
• /
• v.34 no.4
• /
• pp.385-394
• /
• 2022

Global Warming has been driven majorly by the consumption of fossil fuels. Harnessing energy from wind is viable solution towards reducing carbon footprint created due to burning such fuels, However, wind turbines have their problems of flow separation and aerodynamic stall to tackle with. In an attempt to delay the stall angle and improve the aerodynamic characteristics of the NACA 0015 symmetrical aerofoil, lateral cylindrical ridges were attached to its suction surface, at chord positions ranging from 0.1c to 0.5c. The characteristics of the original and ridged aerofoils were obtained using simultaneous pressure readings taken in a wind tunnel, at a free stream Reynolds number of R_e = 2.81 × 10⁵ for a wide range of free stream angles of attack ranging from -45° to 45°. Depending on the ridge size, a delay in stall angle varying from 5° to 20° was achieved together with the maximum increase in lift in the post-stall phases. Additionally, efforts were made to identify the optimum position for each ridge.

• 한국전산유체공학회:학술대회논문집
• /
• 2003.10a
• /
• pp.74-74
• /
• 2003