• Nuclear Engineering and Technology
• /
• v.47 no.5
• /
• pp.513-522
• /
• 2015

The present paper aims at improving the modeling of turbulence for the upward turbulent bubbly flow through the use of experimental databases that contain data on small and large vertical ducts. First, the role of bubble-induced turbulence was analyzed, which indicated the dominant role of the bubble-induced turbulence in the duct center for relatively high void fraction cases. Therefore, the turbulence therein was mainly focused on, which indicated that the stronger turbulence could be induced by bubbles in large ducts with similar void fractions as compared to that in small ducts. Next, the turbulence of upward turbulent bubbly flow near the wall is discussed to understand the interaction between the wall-induced and bubble-induced turbulence. It showed that the existence of a wall could suppress the bubble-induced turbulence given the same void fraction, and the existence of bubbles could also suppress the solely wall-induced turbulence as compared to the single-phase turbulent flow, even though the total turbulence is enhanced. The above characteristics indicated that the current turbulence modeling method needs to be modified, especially when the bubble-induced turbulence plays a dominant role.

• Wind and Structures
• /
• v.35 no.2
• /
• pp.131-146
• /
• 2022

Tornadic wind flow is inherently turbulent. A turbulent wind flow is characterized by fluctuation of the velocity in the flow field with time, and it is a dynamic process that consists of eddy formation, eddy transportation, and eddy dissipation due to viscosity. Properly modeling turbulence significantly increases the accuracy of numerical simulations. The lack of a clear and detailed comparison between turbulence models used in tornadic wind flows and their effects on tornado induced pressure demonstrates a significant research gap. To bridge this research gap, in this study, two representative turbulence modeling approaches are applied in simulating real-world tornadoes to investigate how the selection of turbulence models affects the simulated tornadic wind flow and the induced pressure on structural surface. To be specific, LES with Smagorinsky-Lilly Subgrid and k-ω are chosen to simulate the 3D full-scale tornado and the tornado-structure interaction with a building present in the computational domain. To investigate the influence of turbulence modeling, comparisons are made of velocity field and pressure field of the simulated wind field and of the pressure distribution on building surface between the cases with different turbulence modeling.

• Wind and Structures
• /
• v.6 no.2
• /
• pp.91-106
• /
• 2003

The paper presents the results of 1:50 geometrical scale laboratory modeling of wind-induced point pressure on the roof of the Texas Tech University (TTU) test building. The nominal (prevalent at the TTU site) wind and two bounding (low and high turbulence) flows were simulated in a boundary-layer wind tunnel at Colorado State University. The results showed significant increase in the pressure peak and standard deviation with an increase in the flow turbulence. It was concluded that the roof mid-plane pressure sensitivity to the turbulence intensity was the cause of the previously reported field-laboratory mismatch of the fluctuating pressure, for wind normal and $30^{\circ}$-off normal to the building ridge. In addition, it was concluded that the cornering wind mismatch in the roof corner/edge regions could not be solely attributed to the wind-azimuth-independent discrepancy between the turbulence intensity of the approach field and laboratory flows.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.20 no.4
• /
• pp.419-425
• /
• 2014

The current work investigated the variation of numerical solutions according to the grid number, the distance of the first grid point off the ship surface, turbulence modeling and discretization. The subject vessel is KVLCC. A commercial code, Gridgen V15 and FLUENT were used the generation of the ship hull surface and spatial system and flow computation. The first part of examination, the effect of solutions were accessed depending on the grid number, turbulence modeling and discretization. The second part was focus on the suitable selection of the distance of the first grid point off the ship surface: $Y_P+$. When grid number and discretization were fixed the same value, the friction resistance showed differences within 1 % but the pressure resistance showed big differences 9 % depending on the turbulence modeling. When $Y_P+$ were set 30 and 50 for the same discretization, friction resistance showed almost same results within 1 % according to the turbulence modeling. However, when $Y_P+$ were fixed 100, friction resistance showed more differences of 3 % compared to $Y_P+$ of 30 and 50. Whereas pressure resistance showed big differences of 10 % regardless of turbulence modeling. When turbulence modeling and discretization were set the same value, friction, pressure and total resistance showed almost same result within 0.3 % depending on the grid number. Lastly, When turbulence modeling and discretization were fixed the same value, the friction resistance showed differences within 5~8 % but the pressure resistance showed small differences depending on the $Y_P+$.

• Water Engineering Research
• /
• v.3 no.4
• /
• pp.247-258
• /
• 2002

This paper presents a non-isotropic turbulence modeling of flows over bedforms. The Reynolds stress model is used for the turbulence closure. In the model, Launder, Reece, and Rodi's model and Hanjalic and Launder's model are employed f3r the pressure strain correlation term and the diffusion term, respectively. The mean flow and turbulence structures are simulated and compared with profiles measured in the experiments. The numerical solutions from two-equation turbulence models are also provided for comparisons. The Reynolds stress model yields the separation length of eddy similar to the other numerical results. Using the developed model, the resistance coefficients are also estimated for the flows at different Froude numbers. Karim's (1999) relationship is used to determine the bedform geometry. It is found that the values of the form drag and the skin friction are very similar to those obtained by the other turbulence models. meaning higher values of the form drag and lower values of the skin friction compared with the empirical formulas.

• Wind and Structures
• /
• v.2 no.4
• /
• pp.305-323
• /
• 1999

Accurate turbulence modeling is an essential prerequisite for the use of Computational Fluid Dynamics (CFD) in Wind Engineering. At present the most popular turbulence model for general engineering flow problems is the ${\kappa}-{\varepsilon}$ model. Models such as this are based on the isotropic eddy viscosity concept and have well documented shortcomings (Murakami et al. 1993) for flows encountered in Wind Engineering. This paper presents an objective assessment of several available alternative models. The CFD results for the flow around a full-scale (6 m) three-dimensional surface mounted cube in an atmospheric boundary layer are compared with recently obtained data. Cube orientations normal and skewed at $45^{\circ}$ to the incident wind have been analysed at Reynolds at Reynolds number of greater than $10^6$. In addition to turbulence modeling other aspects of the CFD procedure are analysed and their effects are discussed.

• 한국연소학회:학술대회논문집
• /
• 2015.12a
• /
• pp.23-24
• /
• 2015

In this talk, we will present what we believe is the state-of-the-art of the numerical modeling and simulation of the combustion processes as they relate to typical scramjet engines. The free-stream Mach number is hypersonic, but the speed is not sufficiently decelerated at the inlet/isolator, as in ramjets, so that combustion takes place under supersonic conditions. This creates some difficulties for most turbulence-combustion models. We delve into the details of these problems, by discussing the software programs that have a long track record for scramjet combustion simulation; with a focus on the accuracy of the baseline numerical methods used, the turbulence modeling/simulation approach, the comparative fidelity of the turbulence-combustion interaction models, ability to simulate premixed/non-premixed/partially-premixed, quenching/re-ignition capabilities, the numerical spark-plug method, Damkholer number regimes supported, and the effects of variable Prandtl, Schmidt, and Lewis numbers. Validation results from high-speed and low-speed combustion applications will also be presented.

• Journal of Environmental Science International
• /
• v.19 no.2
• /
• pp.137-148
• /
• 2010

This paper investigates the characteristics of turbulence schemes. Turbulence closures are fundamental for modeling the atmospheric diffusion, transport and dispersion in the boundary layer. In particular, in non-homogeneous conditions, a proper description of turbulent transport in planetary boundary layer is fundamental aspect. This study is based on the Regional Atmospheric Modeling System (RAMS) and combines four different turbulence schemes to assess if the different schemes have a impact on simulation results of vertical profiles. Two of these schemes are Isotropc Deformation scheme (I.Def) and Anisotropic deformation scheme (A.Def) that are simple local scheme based on Smagorinsky scheme. The other two are Mellor-Yamada scheme (MY2.5) and Deardorff TKE scheme (D.TKE) that are more complex non-local schemes that include a prognostic equation for turbulence kinetic energy. The simulated potential temperature, wind speed and mixing ratio are compared against radiosonde observations from the study region. MY2.5 shows consistently reasonable vertical profile and closet to observation. D.TKE shows good results under relatively strong synoptic condition especially, mixing ratio simulation. Validation results show that all schemes consistently underestimated wind speed and mixing ratio but, potential temperature was somewhat overestimated.

• Wind and Structures
• /
• v.5 no.2_3_4
• /
• pp.209-226
• /
• 2002

When predicting unsteady flow and pressure fields around a structure in a turbulent boundary layer by Large Eddy Simulation (LES), velocity fluctuations of turbulence (inflow turbulence), which reproduce statistical characteristics of the turbulent boundary layer, must be given at the inflow boundary. However, research has just started on development of a method for generating inflow turbulence that satisfies the prescribed turbulence statistics, and many issues still remain to be resolved. In our previous study, we proposed a method for generating inflow turbulence and confirmed its applicability by LES of an isotropic turbulence. In this study, the generation method was applied to a turbulent boundary layer developed over a flat plate, and the reproducibility of turbulence statistics predicted by LES computation was examined. Statistical characteristics of a turbulent boundary layer developed over a flat plate were investigated by a wind tunnel test for modeling the cross-spectral density matrix for use as targets of inflow turbulence generation for LES computation. Furthermore, we investigated how the degree of correspondence of the cross-spectral density matrix of the generated inflow turbulence with the target cross-spectral density matrix estimated by the wind tunnel test influenced the LES results for the turbulent boundary layer. The results of this study confirmed that the reproduction of cross-spectra of the normal components of the inflow turbulence generation is very important in reproducing power spectra, spatial correlation and turbulence statistics of wind velocity in LES.

• Journal of Advanced Navigation Technology
• /
• v.13 no.6
• /
• pp.820-830
• /
• 2009

This paper illustrates how simulation modeling can be reduced of ground turbulence by the constructions in the vicinity of airport runway and reports on a cause of ground turbulence using two-dimensional CFD analysis. Interesting result is that the shape in cross-section show the higher ground turbulence than the height of the building. The predicted results confirmed reduction of wind-effect by doing that set up the building with a fence, terraced shape or gap and it can generate turbulence in embryo at this stage. We knows that cross-wind effect in the vicinity of airport runway is highly dependent on the shape of the buildings.