• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.19 no.1
• /
• pp.51-56
• /
• 1983

In the stability problem of the U-grooved plate, it has a circular hole, the site of the hole determines some different deformation mode when it was loaded. To determine the optimal position of the circular hole-center which not to get large distortion of the hole itself, in this paper, we studied the distributions of stresses in the neck area between hole and U-groove and the distortion mode of the deformed hole by B.E.M(Boundary Element Method) and compared with experimental results in four cases. For a distributed load, according to the center of the hole moves closer to the U-groove center (c.-c. line), the shape of the circular hole was transformed to the elliptical one(it's major axis perpendicular to the c.-c. line). In this problem, the results by Boundary Element Method was well accorded with Experiments.

• Tribology and Lubricants
• /
• v.29 no.3
• /
• pp.149-159
• /
• 2013

In this research, the lubrication characteristics of spool valves with various cross-sectional groove shapes were studied. The validity of using the Reynolds equation for the analysis of spool valves with various groove shapes was also investigated. The cross-sectional shapes for the grooves included a triangle, square, and U shape. The characteristics of the flow in the groove were investigated using streamlines. When the number of grooves was increased, the difference between the results obtained from the Reynolds equation and those obtained from the Navier-Stokes equation increased according to the groove shape. Thus, it was found that the Navier-Stokes equation should be used to investigate the lubrication characteristics of the spool valves in those cases. Moreover, in the case where the cross section of the groove was U-shaped, the groove prevented the small eddy current from occurring in the groove. Therefore, the lateral force and friction force of the spool valve with the U-shaped groove were lower than those of the spool valves with other groove shapes.

• Korean Journal of Materials Research
• /
• v.23 no.2
• /
• pp.116-122
• /
• 2013

For fabricating silicon solar cells with high conversion efficiency, texturing is one of the most effective techniques to increase short circuit current by enhancing light trapping. In this study, four different types of textures, large V-groove, large U-groove, small V-groove, and small U-groove, were prepared by a wet etching process. Silicon substrates with V-grooves were fabricated by an anisotropic etching process using a KOH solution mixed with isopropyl alcohol (IPA), and the size of the V-grooves was controlled by varying the concentration of IPA. The isotropic etching process following anisotropic etching resulted in U-grooves and the isotropic etching time was determined to obtain U-grooves with an opening angle of approximately $60^{\circ}$. The results indicated that U-grooves had a larger diffuse reflectance than V-grooves and the reflectances of small grooves was slightly higher than those of large grooves depending on the size of the grooves. Then amorphous Si:H thin film solar cells were fabricated on textured substrates to investigate the light trapping effect of textures with different shapes and sizes. Among the textures fabricated in this work, the solar cells on the substrate with small U-grooves had the largest short circuit current, 19.20 mA/$cm^2$. External quantum efficiency data also demonstrated that the small, U-shape textures are more effective for light trapping than large, V-shape textures.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2003.05a
• /
• pp.148-151
• /
• 2003

The purpose of this study is to investigate the manufacturing technique on the U type Draw-Bending of inner groove tube. The U type tube requires the quality of product that satisfy sufficient conditions for a heat exchanger. The mandrel components act the important roles that prevent wrinkles and keep the shape of cross section of bended tube at bending process. We performed the FEM simulation using LS-DYNA software and the bending test of inner groove tube and then, compared bending simulation with bending test results about mandrel ball diameter, mandrel position and optimal clearance between mandrel and tube.

• Transactions of The Korea Fluid Power Systems Society
• /
• v.4 no.4
• /
• pp.15-20
• /
• 2007

All of the hydraulic spool valves adopt radially grooved spools to avoid hydraulic locking. In this paper, a commercial computational fluid dynamics (CFD) code, FLUENT is used to investigate the accurate Poiseuille flow characteristics inside single groove. The stream lines, velocity and pressure distributions are obtained for various groove widths, depths and shapes. The stream lines are highly affected by groove shape and there occurred large vortexes inside groove beyond a certain ratio of groove width to depth. Especially the U shaped groove restrains the occurrence of vortex. Therefore the numerical method adopted in this paper can be use in optimum designing of multi-grooved hydraulic spool valves.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.25 no.2
• /
• pp.260-268
• /
• 2001

Wake structures behind two circular cylinders with different groove configurations(U and V-shape) have been investigated experimentally. The results were compared with those for the smooth cylinder having the same diameter D. The drag force, mean velocity and turbulent intensity profiles of wake behind the cylinders were measured with varying the Reynolds number in the range of Re(sub)D=8,000∼14,000. As a result, the U-shaped groove was found to reduce the drag up to 18.6%, but the V-shaped groove reduced drag force only 2.5% compared with the smooth cylinder. As the Reynolds number increases, the vortex shedding frequency becomes a little larger than that of the smooth cylinder. The visualized flow using the smoke-wire and particle tracing methods shows the flow structure qualitatively.

• Journal of the Korean Vacuum Society
• /
• v.11 no.4
• /
• pp.249-255
• /
• 2002

For a formation of membrane structures, single crystal silicon wafers have been anisotropically etched with solutions of KOH and KOH-IPA. The etching rate was observed to be strongly dependent upon the etchant temperature and concentration. Mask patterns for the etching experiment was aligned to incline $45^{\circ}$on the primary flat of the silicon wafer. The different etching characteristics were observed according to pattern directions and etchant concentration. When the KOH concentration was fixed to 20 wt%, the U-groove etching shape was observed for the etching temperature of above $80^{\circ}C$, and V-groove shapes observed at below $80^{\circ}C$. Hillocks, which were generated at the etched silicon surfaces, has been decreased as the increasing of the etchant temperature and concentration.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.20 no.1
• /
• pp.154-162
• /
• 1996

Ball screws are commonly used in linear motion feeding systems of various machine tools and automated systems. They are known to have relatively little backlash, high precision and efficiency compared to ordinary lead screws. Furthermore, the effectiveness of ball screw has made it the preferred choice of many newly developed high speed precision feeding units. The motivation of this work is to establish the groove edsigh basis of ball screws for the reduction of contact fatigue failure. In most instances, fatigue failure between ball and shaft groove is due to excessive contact pressure. Especially, the excessive load is causative of plastic flow below the contact surface, which can contribute to surface failure. But, in spite of small load, if groove conformity rate is large, contact pressure is increased and internal shear stress reach the yield value of the material. In such a point, the authors deal with design procedure for deciding the permissible conformity rate of a ball screw groove with the computational evaluation of contact pressure and maximum shear stress.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2008.05a
• /
• pp.425-426
• /
• 2008

Elasto-plastic finite element analysis was carried out for analyzing the severe plastic deformation behavior of copper specimens during groove pressing. Deformation localization was studied in terms of strain variations along the longitudinal direction. Plastic strain is lower at the local interface between the shear and the flat regions, which receive very little shear during the pressing cycle. Strain localization is more intensified with the number of rove pressing cycles, although the average strain level increases.

• Journal of Technologic Dentistry
• /
• v.42 no.3
• /
• pp.220-227
• /
• 2020

Purpose: This study aims to investigate the cusp variation pattern of the Korean mandibular second premolar and to determine the difference in tooth diameter and surface area using a virtual three-dimensional model. Methods: Dental casts from 69 students were scanned as a virtual dental models with a three-dimensional dental model scanner. Tooth diameter, absolute and relative individual areas, total crown area, the number of lingual cusps and central groove pattern were analyzed using RapidForm 2004. The Mann-Whitney U-test and the Kruskal-Wallis test were performed to verify sexual dimorphism, the difference in tooth diameter and surface according to the cusp variation pattern (α=0.05). Results: There was no significant difference except in buccolingual diameter (p<0.05) and buccolingual diameter at the cervix (p<0.05). The relative surface area of the total clinical crown was 65.76% for the buccal half and 34.24% for the lingual half, with a ratio of 2:1. In the case of the presence of two lingual cusps, the ratio was 21.47% for the mesiolingual half and 14.12% for the distaolingual half, with a ratio of 3:2. The dominant central groove patterns of the second premolar were the H-pattern (42.0%), followed by the Y-pattern (37.7%), then the U-pattern (20.3%). The relative buccal half was largest in the U-pattern central groove and the relative lingual half was largest in the Y-pattern central groove (p<0.05). Conclusion: This study is significant in that it measured quantitative surface areas and the findings could be a meaningful reference to comprehend dental anatomy in Koreans.