• 한국진공학회지
• /
• 제1권1호
• /
• pp.24-27
• /
• 1992

The Pohang Accelerator Lab is constructing a 2 GeV synchrotron radiation source. In order to achieve a beam lifetime of 5 hours or more, the average pressure in the vacuum chamber will be kept in the nano Torr range. Each chamber consists of a top and a bottom piece, which are machined separately and welded together. The chamber material is A1 5083-H321. The pumping system has nine sets of lumped NEGs in tandem with ion pumps installed beneath photon stops, and six ion pumps per superperiod. A prototype chamber will be machined by February 1992. After various tests with the prototype chamber, the vacuum chamber design will be refined.

• International journal of advanced smart convergence
• /
• 제7권4호
• /
• pp.84-91
• /
• 2018

In this paper, we simulated three different HV systems and analyzed of each vacuum characteristics by VacCAD modelling. In each of modelled vacuum systems, selection of chamber materials, combination of rough pump with high vacuum pump and conductance of roughing line (diameter and length) were proposed as system variables. In the modelling of chamber materials, the pumping times to ultimate pressures of different chamber materials (stainless steel, aluminum) were compared by the variations of chamber volume. In this model, the effects of outgassing dependent on the chamber materials was also simulated and aluminum was estimated to optimum chamber materials. It was also obtained that modelling of vane and roots pump with diffusion pump and diameter, length of $50{\times}250$ [mm]roughing line were characterized as optimum variables to reach the ultimate pressure of 10E-7 [mbar] most effectively. Optimum design factors for vacuum characteristics of modelled vacuum system were achieved by VacCAD simulations. Feasibility of VacCAD as vacuum simulator was verified and applications of VacCAD expected to be increased to fields in vacuum needed.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2009년도 제37회 하계학술대회 초록집
• /
• pp.308-308
• /
• 2009

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2009년도 춘계학술대회 논문집
• /
• pp.361-364
• /
• 2009

마이크로 인공위성에 적용가능한 마이크로 추력기를 개발하기 위해서는 우주환경을 모사할 수 있는 진공설비가 요구된다. 본 논문에서는 $10^{-5}\;torr$의 진공도를 목표로 정하고 진공설비를 구축하였고, $100{\sim}120\;km$의 고도를 모사한다. 장치 선정 및 실제 장치 구축 후 진공도 성능 실험을 수행하였고 저진공 펌프를 작동시켜 누센펌프의 멤브레인에 따른 특성연구를 진행하였다. 또한 향후 열진공챔버로의 전환을 위한 계획을 서술하였다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2010년도 제39회 하계학술대회 초록집
• /
• pp.42-42
• /
• 2010

We, previously, proved that the noise in the vertical readback from some of beam position monitors (BPMs) in the vacuum chamber of Pohang Light Source (PLS) are caused by the transverse electric (TE) longitudinal harmonic resonances. Based on this analysis, we now design the shunt structure to remove the TE mode resonces near the BPMs operation frequency of 500 MHz in the storage ring vacuum chamber of PLS upgrade project (PLS-II). The simulation result and experimental test result will be presented.

• Nuclear Engineering and Technology
• /
• 제38권5호
• /
• pp.455-458
• /
• 2006

The HANARO reactor has a vertical hole for a cold neutron source (CNS) in the heavy-water reflector tank, i.e., the CNS hole, which was considerably deformed during its welding to the horizontal cold neutron (CN) beam tube. This paper presents an investigation of the form of the CNS hole for the optimal design of the a vacuum chamber for the CNS. In addition, the installation method of the vacuum chamber into the CNS hole for minimizing the water thickness between the vacuum chamber and the nose of the CN beam tube is proposed.

• 한국항공우주학회지
• /
• 제34권12호
• /
• pp.90-95
• /
• 2006

위성 열평형 시험에 사용하는 열진공 챔버의 벽은 흑체 거동을 하는 우주공간과는 달리 위성의 복사 에너지를 완벽하게 흡수하지 못하고 일부를 반사한다. 챔버의 크기가 작을수록 이러한 챔버 벽 효과는 커지는 것으로 알려져 있다. 이것은 시험비용을 줄이기 위해 대형 챔버를 사용하기 힘든 소형위성의 개발에 걸림돌이 된다. 본 연구에서는 챔버 벽 효과를 예측하고 이를 보정하기 위한 정량적인 분석을 진행하였다. 그 결과로 챔버 벽 효과에 의한 온도 오차를 계산하여 시험 데이터를 보정할 수 있게 하였다. 또, 최적 면적비를 정의하여 소형위성의 열평형 시험용 열진공 챔버의 크기를 정하는데 기준을 마련하였다. 덧붙여 챔버 벽을 투명한 재질로 코팅하여 챔버 벽 효과를 줄일 수 있는 방안에 대해 이론적인 분석을 수행하였다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2014년도 제46회 동계 정기학술대회 초록집
• /
• pp.151.1-151.1
• /
• 2014

Wake field effect on the electron beam from the undulator chamber in PAL-XFEL is analyzed. The wake field takeover some energy from the electron beam which will increase the energy spread of the electron beam. This will cause the degradation of the radiation power in PAL-XFEL. To decrease the effect, the surface of the undulator vacuum chamber should be fabricated with 200 nm surface roughness and 5 nm oxidation layer. In this presentation, the numerical calculation of the wake will be shown. Simulation results of the radiation generation in PAL-XFEL also will be presented.

• Applied Science and Convergence Technology
• /
• 제23권2호
• /
• pp.97-102
• /
• 2014

A vacuum chamber for a commercial atomic force microscope (AFM) is designed and fabricated. Only minimal modifications were made to an existing microscope in an effort to work in a vacuum environment, while most of the available AFM functionalities were kept intact. The optical alignment needed for proper AFM operations including a SLD (superluminescent diode) and a photodiode can be made externally without breaking the vacuum. A vacuum level of $5{\times}10^{-3}$ torr was achieved with a mechanical pump. An enhancement of the quality factor was observed along with a shift in the resonance frequency of a non-contact-mode cantilever in a vacuum. Topographical data of a calibration sample were also obtained in air and in a low vacuum using the non-contact mode and the results were compared.

• Applied Science and Convergence Technology
• /
• 제24권4호
• /
• pp.84-89
• /
• 2015

The base pressure and outgassing rate of a mild steel chamber were measured and compared to those of a stainless steel chamber. A combined sputter-ion and non-evaporable getter pump with a nominal pumping speed of 490 l/s generated the base pressure of $2.7{\times}10^{-11}$ mbar in the mild steel chamber and $1.2{\times}10^{-10}$ mbar in the stainless steel chamber. The rate-of-rise measurements show that the mild steel has an extremely low outgassing rate of $2.6{\times}10^{-13}$ mbar $ls^{-1}cm^{-2}$, which is about one-order of magnitude smaller than the outgassing rate of the stainless steels. Vacuum annealing of the mild steel at $850^{\circ}C$ reduced the outgassing rate further to $8.8{\times}10^{-14}$ mbar $ls^{-1}cm^{-2}$, which was comparable to the outgassing rate of a heat treated stainless steel for extreme-high vacuum use.