• Journal of Auto-vehicle Safety Association
• /
• v.10 no.1
• /
• pp.32-37
• /
• 2018

This paper proposes autonomous speed control strategy for an Electric Vehicle on urban road. SNU campus road is used to reperesent urban road situation. Motor efficiency of driving on campus circulation road can be improved by controlling velocity properly. Given information of campus road, especially slope of road, acceleration is selected from candidate, considering consumed power, human factor and driving time. To apply urban situation, preceding vehicle is also considered. With preceding vehicle, acceleration is defined according to clearance and relative velocity. Acceleration is bounded in normal range. Proposed acceleration control method is activated with proper velocity range for campus circulation road. With acceleration control, motor efficiency becomes better than driving with constant vehicle. To evaluate the performance of proposed acceleration controller, simulation study is conducted via MATLAB.

• Journal of Auto-vehicle Safety Association
• /
• v.14 no.1
• /
• pp.39-44
• /
• 2022

This paper presents a development of throttle and brake controller for autonomous vehicle simulation environment. Most of 3D simulator control autonomous vehicle by throttle and brake command. Therefore additional longitudinal controller is required to calculate pedal input from desired acceleration. The controller consists of two parts, feedback controller and feedforward controller. The feedback controller is designed to compensate error between the actual acceleration and desired acceleration calculated from autonomous driving algorithm. The feedforward controller is designed for fast response and the output is determined by the actual vehicle speed and desired acceleration. To verify the performance of the controller, simulations were conducted for various scenarios, and it was confirmed that the controller can successfully follow the target acceleration.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.24 no.8
• /
• pp.592-599
• /
• 2014

A torsional vibration at driveline happens seriously at rapid vehicle acceleration. The torsional vibration at driveline can be reduced by optimization of joint angle and yoke phase angle of driveline. But, the joint angle of driveline is changed according to vehicle driving condition as acceleration, deceleration, forward and backward driving, so that excessive vibration is transmitted to vehicle body at specific driving condition. Especially under rapid acceleration condition, vibration transmitted to body could be maximized because excitation force at rapid acceleration is bigger than that at normal driving condition due to changed joint angle. The torsional vibration of driveline can be kept at low level by controlling suspension parameter to minimize rigid axle displacement as well as optimizing joint angles considering the vehicle acceleration condition.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.65 no.4
• /
• pp.642-651
• /
• 2016

For the acceleration and brake systems of an autonomous vehicle, the dynamic models from acceleration (brake) pedal input to driving(braking) torque at the vehicle wheel are represented by a set of linear transfer functions in this paper. We present an experimental method that can identify these models using a single rectangular pulse response data. Various magnitude of inputs with different running speeds are applied to experimental tests. All the identified models are demonstrated by the measured data. Both acceleration and brake models have been also validated by comparing the velocity of a full vehicle model associated with the proposed models with the measured vehicle velocity.

• Advances in aircraft and spacecraft science
• /
• v.10 no.1
• /
• pp.1-18
• /
• 2023

This paper investigates the integrated control of an air-breathing hypersonic vehicle considering the safety of propulsion system under acceleration. First, the vehicle/engine coupling model that contains a control-oriented vehicle model and a quasi-one-dimensional dual-mode scramjet model is established. Next, the coupling process of the integrated control system is introduced in detail. Based on the coupling model, the integrated control framework is studied and an integrated control system including acceleration command generator, vehicle attitude control loop and engine multivariable control loop is discussed. Then, the effectiveness and superiority of the integrated control system are verified through the comparison of normal case and limiting case of an air-breathing hypersonic scramjet coupling model. Finally, the main results show that under normal acceleration case and limiting acceleration case, the integrated control system can track the altitude and speed of the vehicle extremely well and adjust the angle deflection of elevator to offset the thrust moment to maintain the attitude stability of the vehicle, while assigning the two-stage fuel equivalent ratio to meet the thrust performance and safety margin of the engine. Meanwhile, the high-acceleration requirement of the air-breathing hypersonic vehicle makes the propulsion system operating closer to the extreme dangerous conditions. The above contents demonstrate that considering the propulsion system safety will make integrated control system more real and meaningful.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.21 no.1
• /
• pp.41-48
• /
• 2022

Vehicle vibration was introduced in the time and frequency domains using fast Fourier transform (FFT) analysis. In particular, a vibration mode analysis and characteristics of the frequency response function (FRF) in a sport utility vehicle (SUV) passing over a bump barrier at different speeds was performed systematically. The response behavior of the theoretical acceleration was obtained using a numerical method applied to the forced vibration model. The amplitude and frequency of the external force on the vehicle cause various power spectra with individual intrinsic system frequencies. In this regard, several modes of power spectra were acquired from the spectra and are discussed in this paper. The proposed technique can be used for monitoring the acceleration in a vehicle passing over a bump barrier. To acquire acceleration signals, various experimental runs were performed using the SUV. These acceleration signals were then used to acquire the FRF and to conduct mode analysis. The vehicle characteristics according to the vehicle condition were analyzed using FRF. In addition, the vehicle structural system and bump passing frequencies were discriminated based on their power spectra and other FRF spectra.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2013.04a
• /
• pp.623-625
• /
• 2013

Tire hydroplaning is one of the most important tire performances, especially for safety on wet road surface. And nowadays various methods such as FEM and FVM analysis are being applied to design and improve tire hydroplaning performance, along with on-vehicle test of tire hydroplaning. Conventional evaluation of tire hydroplaning has been done by comparing peak lateral acceleration and vehicle speed in time domain. But in this paper, frequency domain analysis of lateral acceleration when hydroplaning at high speed has been carried out to get the quantitative comparison between test tires. And it is concluded that the frequency spectrum analysis of lateral acceleration gives much better discrimination, as compared to the conventional time domain analysis of lateral acceleration and vehicle speed.

• International Journal of Highway Engineering
• /
• v.15 no.4
• /
• pp.147-154
• /
• 2013

PURPOSES: To analyze the specific factors of drivers behaviors that amount of cause the greenhouse gas emissions per vehicle. METHODS: Drivers behaviors at intersections are analyzed on the conditions of acceleration and deceleration. RESULTS : First, it is resulted greenhouse gas emissions per vehicle is produced more at intersections than at the main lines of highway. Second, it is resulted that the average speed, the average acceleration rate and the maximum speed are three major factors to produce greenhouse gas per vehicle in acceleration sections. Third, it is resulted that rapid deceleration 20m before entering intersections is the major factor to produce greenhouse gas per vehicle in deceleration sections. CONCLUSIONS: At intersections, sudden acceleration and deceleration is not good for greenhouse gas emissions. Thus, and the average speed, the average acceleration rate and the maximum speed are the chosen as factors to be controlled for drivers' behavior to reduce vehicles' greenhouse gas at intersections.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.17 no.6
• /
• pp.54-66
• /
• 2018

In this study, vehicle speeds at acceleration and deceleration lanes of rest areas for drowsy drivers were investigated to analyze effects of acceleration and deceleration lane lengths, grades and curve radius. In addition, we used VISSM to analyze proper lengths of rest area's acceleration and deceleration lanes. Several VISSIM scenarios with different lengths of acceleration and deceleration lane were constructed. Through VISSIM simulation, we collected individual vehicle speed data to analyze speed changes by different lengths of acceleration and deceleration lanes. As a result of the vehicle speed change investigation, grades and curve radii of the rest area affected the speed, most of all lengths of acceleration and deceleration lane showed a great effect on the vehicle speed. In the case of short lengths of acceleration and deceleration lane, speed variation among vehicles was significant. If the deceleration lane length is short, the vehicle enters a state in which the speed is not sufficiently reduced, and if the acceleration lane length is short, the vehicle enters a state in which the speed is not sufficiently accelerated showing high risks of conflicts and accidents. It is recommended that 245m length of deceleration lane and 370m length of acceleration lane should be installed at least to secure safety and manage conflicts relevantly.

• Journal of the Korean Society for Precision Engineering
• /
• v.17 no.6
• /
• pp.111-118
• /
• 2000

The design of reference trajectory with respect to drag acceleration is necessary to decelerate from hypersonic speed safely after atmosphere re-entry of space vehicle. The re-entry guidance design involves trajectory optimization, generation of a reference drag acceleration profile with the satisfaction of 6 trajectory constraints during the re-entry flight. This reference drag acceleration profile can be considered as the reference trajectory. The cost function is composed of the accumulated total heating on vehicle due to the reduction of weight. And a regularization is needed to prevent optimal drag profile from varying too fast and achieve realized trajectory. This paper shows the relations between velocity, drag acceleration and altitude in drag acceleration profile, and how to determine the reference trajectory.