• 한국항공운항학회지
• /
• 제24권3호
• /
• pp.62-68
• /
• 2016

According to the accident/incident reports of aircraft runway overruns and excursions, it generally shows runway friction reduction and aircraft braking capability deterioration are the basic causes due to adverse weather. Although surface of paved runway gets wet, it also should give good friction capability. If runway surface is worn due to long time usage and friction capability is reduced due to rubber accumulation or weather conditions(snow, rain, ice etc.), airport authorities should rapidly measure friction coefficient and give them to relevant persons through aeronautical information system and support safe takeoff and landing. Operation wise, these information of friction coefficient reduction should be lead to aircraft performance adjustments, but the data from manufacturer(performance manual) are airplane braking coefficient and the data from airport authorities are vehicle measured braking coefficient. But these two data are considered as the same meaning although the definite relationship between them is not clarified yet. So I am trying to search for the technical background of these two data and suggest reasonable method to use them efficiently.

• 한국산학기술학회논문지
• /
• 제19권11호
• /
• pp.541-549
• /
• 2018

본 연구에서는 국내 화물 및 여객차량들을 견인하는 디젤전기 기관차의 제동에 따른 동적 거동을 분석하기 위하여 제동장치에 영향을 미치는 마찰계수, 제동압력, 주행저항 등을 시험하였다. 마찰계수는 UIC 541-4를 참고로 Dynamo 시험을 수행하였으며 시험결과는 다변량 회귀분석을 통해 제동하중, 제동초기 속도와의 관계를 분석하여 제시하였다. 제동압력은 상용제동과 비상제동으로 구분하였으며, 제동밸브와 배관의 특성을 반영하기 위하여 시간에 따른 제동압력 변화를 대상 차량에서 측정하였다. 차량에 작용하는 외력을 반영하기 위하여 EN 14067-4의 타행시험을 수행하고 2차 다항식 형태의 주행저항을 제시하였다. 도출한 주행저항을 동일 차종에 대하여 각 국가별로 사용하고 있는 주행저항들과 비교하였다. 차량의 재원, 마찰계수, 제동압력, 주행저항을 바탕으로 직선 평탄 선로를 주행하는 디젤전기기관차의 동적 거동을 EN 14531-1에서 제시된 시간적분을 이용하여 해석하였다. 해석 결과는 상용제동과 비상제동에 대하여 각각 차량의 속도이력 시험결과와 비교 검증하였으며 상당히 합리적인 결과를 도출하였다. 본 연구의 결과들은 철도차량들을 연결하여 운행하는 열차의 동적 거동해석에 활용할 수 있을 뿐 아니라 차량 설계에서 제동에 영향을 미치는 다양한 파라미터들을 분석하고 성능향상의 기초자료로 활용할 수 있을 것으로 기대된다.

• 자동차안전학회지
• /
• 제7권3호
• /
• pp.19-24
• /
• 2015

Brake pads are a component of disc brake system of automobile and consist of steel backing plates and friction material facing the disk brake rotor. Due to the repeated sliding forces and torque in vehicle braking, friction performance of brake pads are ensured. Futhermore, the brake pad is one of major tuning components in aftermarket, mechanical characteristics of the brake pad are necessary to evaluate for establishing the certification standards of tuning components. This study had performed the five specimen tests for friction coefficients and wear loss rates according to the SAE test specification. Using the instrumented indentation method, yield strength and tensile strength were measured. Friction coefficients, 0.386 - 0.489, and wear loss rates, 1.0% - 3.7% are obtained. The range of yield strength and tensile strength are 21.4 MPa - 105.3 MPa and 39.5 MPa - 176.4 MPa respectively.

• 한국자동차공학회논문집
• /
• 제15권2호
• /
• pp.109-114
• /
• 2007

Skid mark and coefficient of friction are usually utilized to calculate the velocity and behavior of vehicles. For a critical case such as traffic accident reconstruction, however, the initial velocity of the car should be calculated precisely. In this study, the skid marks on dry asphalt pavement were measured, and the velocity at brake onset was precisely recovered. A passenger car with new tires and non-contact optical speedometer were set up for the tests. A new methodology to determine the more precise velocity for Non-ABS vehicle at braking onset were suggested.