• Korean Journal of Metals and Materials
• /
• v.46 no.4
• /
• pp.223-226
• /
• 2008

The comparison of sintering behavior and mechanical properties of ultra-fine WC-10wt.%Co and WC-10wt.%Fe hard materials produced by high-frequency induction heated sintering (HFIHS) was accomplished using ultra fine powder of WC and binders(Co, Fe). The advantage of this process allows very quick densification to near theoretical density and prohibition of grain growth in nano-structured materials. Highly dense WC-10Co and WC-10Fe with a relative density of up to 99% could be obtained with simultaneous application of 60 MPa pressure and induced current within 1 minute without significant change in grain size. The hardness and fracture toughness of the dense WC-10Co and WC-10Fe composites produced by HFIHS were investigated.

• Journal of Powder Materials
• /
• v.26 no.2
• /
• pp.132-137
• /
• 2019

Tungsten carbide (WC) hard materials are used in various industries and possess a superior hardness compared to other hard materials. They have particularly high melting points, high strength, and abrasion resistance. Accordingly, tungsten carbide hard materials are used for wear-resistant tools, cutting tools, machining tools, and other tooling materials. In this study, the WC-5wt.%Co, Fe, Ni hard materials are densified using the horizontal ball milled WC-Co, WC-Fe, and WC-Ni powders by a spark plasma sintering process. The WC-5Co, WC-5Fe, and WC-5Ni hard materials are almost completely densified with a relative density of up to 99.6% after simultaneous application of a pressure of 60 MPa and an electric current for about 15 min without any significant change in the grain size. The average grain size of WC-5Co, WC-5Fe, and WC-5Ni that was produced through SPS was about 0.421, 0.779, and $0.429{\mu}m$, respectively. The hardness and fracture toughness of the dense WC-5Co, WC-5Fe, WC-5Ni hard materials were also investigated.

• Journal of Welding and Joining
• /
• v.21 no.2
• /
• pp.50-56
• /
• 2003

Metal matrix composites(MMC) consist of metal matrix into which is distributed a second solid phase. The normal intension is to develop a material with superior mechanical properties (for example increased toughness, stiffness and wear resistance) compared to those inherent in the matrix component. In this study, WC-12%Co/low carbon steel MMC overlays have been prepared by Gas Metal Arc Welding(GMAW) according to feeding rate of WC-12%Co grit. The macro and microstructures were examined using optical microscopy (OM) and scanning electron microscopy(SEM) each other. The characteristics of hardness and wear resistance have been investigated. WC-12%Co/low carbon steel MMC overlays which have been taken good beads without porosity and cracks were manufactured by method of GMAW. Matrix of overlayed surface was seen as fish bone and faceted dendrite structures. It was known that structures were iron tungsten carbides, Fe$_{6}$W$_{6}$C which have been occurred by melting of WC-12%Co grits. After MMC had been tested by block-roll wear test it was known that WC-12%Co/low carbon steel MMC has a excellent wear resistance by exiting Fe6w6c and WC-12%Co grit. The consequence was that region of overlay with Fe$_{6}$W$_{6}$C phase has been showed a model of adhesive wear, but region of overlay with WC-12%Co grit was restrained as a result of mechanism that wear of WC-12%Co grit is not adhesive but fracture.racture.

• Proceedings of the KWS Conference
• /
• 1998.10a
• /
• pp.250-252
• /
• 1998

• Journal of Powder Materials
• /
• v.3 no.4
• /
• pp.266-270
• /
• 1996

The microstructure evolution during sintering of a compact being composed of three layers of (WC-15%Co)/Fe powder mixture with different Fe contents has been observed. The Fe contents in the respective (WC-15%Co)/Fe layers were varied by 20%. 50%, and 90% in sequence by volume from a top layer to a bot- tom layer. The sintering temperatures and times were varied from 110$0^{\circ}C$ to 125$0^{\circ}C$ and from 1 h to 4 h, The compact layer was not densified below 120$0^{\circ}C$ in 4 h. Appropriate sintering temperature and time conditions for making a multi-layered hard metal compact were determined as 125$0^{\circ}C$ and 3 h, respectively.

• Journal of the Korean Society for Heat Treatment
• /
• v.25 no.1
• /
• pp.6-13
• /
• 2012

HVOF thermal spray coating of 80%WC-CoFe powder is one of the most promising candidate for the replacement of the traditional hard chrome plating and hard ceramics coating because of the environmental problem of the very toxic $Cr^{6+}$ known as carcinogen by chrome plating and the brittleness of ceramics coatings. 80%WC-CoFe powder was coated by HVOF thermal spraying for the study of durability improvement of the high speed spindle such as air bearing spindle. The coating procedure was designed by the Taguchi program, including 4 parameters of hydrogen and oxygen flow rates, powder feed rate and spray distance. The surface properties of the 80%WC-CoFe powder coating were investigated roughness, hardness and porosity. The optimal condition for thermal spray has been ensured by the relationship between the spary parameters and the hardness of the coatings. The optimal coating process obtained by Taguchi program is the process of oxygen flow rate 34 FRM, hydrogen flow rate 57 FRM, powder feed rate 35 g/min and spray distance 8 inch. The coating cross-sectional structure was observed scanning electron microscope before chemical etching. Estimation of coating porosity was performed using metallugical image analysis. The Friction and wear behaviors of HVOF WC-CoFe coating prepared by OCP are investigated by reciprocating sliding wear test at $25^{\circ}C$ and $450^{\circ}C$. Friction coefficients (FC) of coating decreases as sliding surface temperature increases from $25^{\circ}C$ to $450^{\circ}C$.

• Journal of Powder Materials
• /
• v.11 no.2
• /
• pp.124-129
• /
• 2004

Nanosized WC and WC-Co powders were synthesised by chemical vapor condensation(CVC) process using the pyrolysis of tungsten hexacarbonyl(W(CO)$_6$) and cobalt octacarbonyl(Co$_2$(CO)$_8$). The microstructural changes and phase evolution of the CVC powders during post heat-treatment were studied using the XRD, FE-SEM, TEM, and ICP-MS. CVC powders were consisted of the loosely agglomerated sub-stoichimetric WC$_{1-x}$ and the long-chain Co nanopowders. The sub-stochiometric CVC WC and WC-Co powders were carburized using the mixture gas of CH$_4$-H$_2$ in the temperature range of 730-85$0^{\circ}C$. Carbon content of CVC powder controlled by the gas phase carburization at 85$0^{\circ}C$ was well matched with the theoretical carbon sioichiometry of WC, 6.13 wt％. During the gas phase carburization, the particle size of WC increased from 20 nm to 40 nm and the long chain structure of Co powders disappeared.

• Journal of the Korean Ceramic Society
• /
• v.51 no.5
• /
• pp.442-446
• /
• 2014

Influences of Co and inhibitors from nano-sized WC materials were observed in the sintering process. VC and $Cr_3C_2$ were used as inhibitors. The crystal structure and surface images of sintered nano-sized WC materials, as functions of Co and inhibitors, were evaluated by XRD and FE-SEM analyses. The relative densities of sintered nano-sized WC materials did not change even with increased quantity of Co and increased temperature. The density of sintered nano-sized WC materials with inhibitors was lower than that of sintered nano-sized WC materials without inhibitors. No difference in hardness due to change of inhibitors was found.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.11a
• /
• pp.144-144
• /
• 2003

Fe-Co-Ge 자기변형 합금 복합체는 낮은 자기장에서도 높은 자기 변형 민감도와 고분자 바인더에 의한 절연으로 인하여 저항이 크고, 와전류 손실이 작아 고주파영역 에서도 우수한 자기변형을 가지는 것으로 보고되고 있다. 그러나 희토류계 자기변형 복합체에 비하여 그 성능은 열세이지만, 제조 단가가 저렴하여 높은 성능/가격 대비 효과를 가지므로 초음파 발진소자와 같은 대량의 상업적 응용분야에 적용 가능한 소재로 있다. [1]. 한편 이와 같은 자기 변형 복합체는 고분자 바인더와 결합되어 있어 그 기계적 특성의 향상과 사용주파수 대역의 증가가 요구되어진다. 이에 이들 문제점을 보안하기 위하여 670 GPa의 큰 영률을 갖는 WC 분말의 첨가에 의한 합금복합체의 기계적 및 자기변형 (정적 및 동적) 특성에 미치는 영향에 관하여 연구하고자 하였다.

• Korean Journal of Materials Research
• /
• v.29 no.1
• /
• pp.52-58
• /
• 2019

The microstructure, hardness, and wear behaviors of a High Velocity Oxygen Fuel(HVOF) sprayed WC-CoFe coating are comparatively investigated before and after laser heat treatments of the coating surface. During the spraying, the binder metal is melted and a small portion of WC is decomposed to $W_2C$. A porous coating is formed by evolution of carbon oxide gases formed by the reaction of the free carbon and the sprayed oxygen gas. The laser heat treatment eliminates the porosity and provides a more densified microstructure. After laser heat treatment, the porosity in the coating layer decreases from 1.7 % to 1.2 and the coating thickness decreases from $150{\mu}m$ to $100{\mu}m$. The surface hardness increases from 1440 Hv to 1117 Hv. In the wear test, the friction coefficient of coating decreases from 0.45 to 0.32 and the wear resistance is improved by the laser heat treatment. The improvement is likely due to the formation of oxide tribofilms.