• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.22 no.6
• /
• pp.148-155
• /
• 2008

This study presents a process control of the wafer edge exposure (WEE) used in 300[mm] wafer environment. WEE, as a key module of the overall track system (coater and developer) for making patterns on wafer, is a system to expose the UV-ray on the wafer to remove a photo resist around edge of the wafer. It can measure, memorize and control the distance and angles from wafer center to edge. Recently in the 300[mm] semiconductor fabrication, the track system strongly requires that WEE station has a controller with high throughput and accuracy to increase process efficiency. We have designed and developed the controller, and present here a WEE control algorithm and experimental results.

• 제어로봇시스템학회:학술대회논문집
• /
• 2002.10a
• /
• pp.55.4-55
• /
• 2002

In the semiconductor fabrication, particle contamination is wide-spread and one of major causes to yield loss. Extensive testing has revealed that even careful handling of wafers during processing may cause photo-resist materials to flake off wafer edges. So, to remove the photo-resist at the outer 5mm of wafers, UV(Ultraviolet) rays are exposed. WEE (Wafer Edge Exposure) process station is the system that exposes the wafer edge as prespecified by controlling the positioning mechanism and maintaining the light intensity level In this work, WEE process station has been designed so as to significantly lower the amount of particle contamination which occurs even during the most r...

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.31A no.7
• /
• pp.69-75
• /
• 1994

A very fine pattern formation process using double exposure is investigated, which can overcome the resolution limit of optical wafer stepper. The very fine pattern can be obtained by moving the edge profile of large pattern by means of moving the stepper stage. The simulation results show that the light transmittance decrease bellow 9%, and the contrast increase to 16.6% for the 0.3$\mu$m photoresist pattern exposeed by the double exposure using i-line wafer stepper. And the experimental results show that fine photoresist pattern as short as 0.2$\mu$m can be obtained without a loss of photoresist thickness. Also, it proves that the depth of focus for 0.3$\mu$m pattern is longer than $1.5\mu$m. And, the very fine negative photoresist pattern was formmed by using the double exposure technique and the image reversal process.

• Journal of Sensor Science and Technology
• /
• v.28 no.4
• /
• pp.251-255
• /
• 2019

We propose a two-step lithography process to minimize edge-bead issues caused by thick photoresist (PR) coating. In the conventional PR process, the edge bead can be efficiently removed by applying an edge-bead removal (EBR) process while rotating the silicon wafer at a high speed. However, applying conventional EBR to the production of desired PR mold with unique negative patterns cannot be used because a lower rpm of spin coating and a lower temperature in the soft bake process are required. To overcome this problem, a two-step lithography process was developed in this study and applied to the fabrication of a polydimethylsiloxane (PDMS) film having super-hydrophobic characteristics. Following UV exposure with a first photomask, the exposed part of the silicon wafer was selectively removed by applying a PR developer while rotating at a low rpm. Then, unique PR mold structures were prepared by employing an additional under-exposure process with a second mask, and the mold patterns were transferred to the PDMS. Results showed that the fabricated PDMS film based on the two-step lithography process reduced the height difference from 23% to 5%. In addition, the water contact angle was greatly improved by spraying of hydrophobic nanosilica on the dual-scaled PDMS surface.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.10a
• /
• pp.141-141
• /
• 2003