• Journal of the Korean Electrochemical Society
• /
• v.2 no.4
• /
• pp.202-208
• /
• 1999

Composite cathodes of $50/50\;vol\%$ LSM-YSZ $(La_{-x}Sr_xMnO_3-yttria\;stabilized\;zirconia)$ were deposited onto dense YSZ electrolytes by colloidal deposition technique. The cathode characteristics were then examined by scanning electron microscopy (SEM) and studied by ac-impedance spectroscopy (IS). The conditioning effects on LSM-YSZ cathodes were seen and remedies for these effects were noted in order to improve the performance of a solid oxide fuel cell (SOFC). The effects of temperature on impedance, surface contamination on cathode bonding to YSZ electrolyte, changing Pt paste, aerosol spray technique applied to curved surface on microstructure and cell to cell variability were solved by testing at $900^{\circ}C$, sanding the YSZ surface, using only one batch of Pt paste, using flat YSZ plates and using consistent procedures and techniques, respectively. And then, reproducible impedance spectra were confirmed by using the improved cell and the typical spectra measured for an (air)LSM-YSZ/YSZ/LSM-YSZ(air) cell at $900^{\circ}C$ were composed of two depressed arcs. Impedance characteristics of the LSM-YSZ cathodes were also affected by experimental conditions such as catalytic interlayer, composite cathode compositions and applied current.

• Journal of the Korean Ceramic Society
• /
• v.37 no.3
• /
• pp.227-232
• /
• 2000

The LSM-YSZ composite electrode as a mixture of LSM and YSZ shows percolation characteristics. It was identified that the polarization resistance of LSM-YSZ composite electrode depend on YSZ connectivity by changing powder size ratio of the DLSM/DYSZ. That is, YSZ in composite electrode showed low electrochemical activity without YSZ connectivity. However, the polarization resistance decreased abruptly with YSZ connectivity due to high electrochemical activity of YSZ in composite electrode. Because the amount of three phase boundary is dependent on LSM and YSZ particle size, the polarization resistance of cathode decreases as LSM and YSZ particle size decreases.

• Journal of the Korean Ceramic Society
• /
• v.38 no.5
• /
• pp.466-473
• /
• 2001

Ni-YSZ 음극의 미세구조와 임피던스특성에 미치는 YSZ 입자크기 및 소결온도의 영향을 고찰하였다. 0.3~0.6$\mu\textrm{m}$의 미세한 NiO 분말을 사용할 경우에는 NiO 분말과 크기가 비슷한 미세한 YSZ 분말(TZ8Y, 0.3$\mu\textrm{m}$)을 첨가했을 때 NiO의 입성장을 억제하는 효과가 가장 크고 환원후 Ni의 입자크기를 미세하게 유지할 수 있는 미세구조를 형성하였다. 또한 미세한 YSZ 분말 (TZ8Y, 0.3$\mu\textrm{m}$)과 조대한 YSZ 분말(FYT13.0, 2$\mu\textrm{m}$)의 혼합비를 달리하여 후막을 제조하였을 때에 TZ8Y 분말만 첨가한 조성이 가장 낮은 분극 저항을 나타내었다. 한편 소결온도는 삼상계면의 양과 분극저항에 영향을 주었으며, 140$0^{\circ}C$에서 소결한 시편의 분극저항이 가장 낮은 값을 나타내었다.

• Bulletin of the Korean Chemical Society
• /
• v.33 no.4
• /
• pp.1177-1182
• /
• 2012

The corrosion resistance of 316L stainless steel coated with NiO-YSZ (Ni added yttria stabilized zirconia) was examined in a proton exchange membrane fuel cell (PEMFC) environment. The NiO-YSZ coating was carried out using a sol-gel dip coating method, and the corrosion resistance and interfacial contact resistance (ICR) were determined by the composition and morphology of the NiO-YSZ film. The corrosion resistance increased with increasing Ni content in the NiO-YSZ film, but rapid corrosion was observed when the YSZ film contained more than 15 wt % Ni due to surface cracks. The polarization resistance was improved by several orders of magnitude when 316L stainless steel was coated with a 15 wt % NiO-YSZ film compared to bare 316L. The ICR of the NiO-YSZ film was decreased to that of bare 316L when the YSZ film contained 25 wt % NiO, suggesting the possible application of NiO-YSZ coated stainless steel for a bipolar plate.

• Journal of Korean Vacuum Science & Technology
• /
• v.2 no.1
• /
• pp.43-48
• /
• 1998

The effect of mcirostructure on the electrical properties of yttria stabilized zirconia (YSZ) was analyzed by modeling layer arrangements and mixed phase structure. The YSZ thin films were deposited by RF magnetron sputtering using 30mol% YSZ and 8 mol% YSZ targets with yttrium pellets on porous alumina substrates. The structure, composition and electricla properties of the YSZ films were investigated as functions of sputtering conditons and layer arrangements by XRD, TEM, XPS and acimpedance spectroscopy. The results showed that the triple palyered YSZ films had highermicrohardness, lower compressive stress state and higher ionic conductivity by one order than single and double layered YSZ films. However, sputtered YSZ films have low conductivity compared to YSZ pellets or doctor bladed YSZ thin plates. These results were probably due to the influence of insulating alumina substrates, impractical for most stacking geometries and inductance induced by relatively long platinum, lead wire on YSZ conductivity.

• Journal of the Korean Ceramic Society
• /
• v.55 no.4
• /
• pp.376-380
• /
• 2018

Microstructural characterization of Ni-yttria-stabilized zirconia (YSZ) anodes using secondary electron images has been limited by a lack of contrast between Ni and YSZ phases. This paper reports a sample preparation method for obtaining secondary electron images that allow the detection of Ni, YSZ, and pore phases together. Ni-YSZ anode samples were obtained by reducing NiO-YSZ samples prepared by using the mixed oxide method. Colloidal silica polishing and electrolytic etching were performed on the Ni-YSZ samples. The morphological change of the sample surface after each polishing process is examined.

• Journal of the Korean Ceramic Society
• /
• v.35 no.9
• /
• pp.917-922
• /
• 1998

The polarization characteristics of the cathodes were discussed which were composed YSZ and ${(La_{0.75 }Sr_{0.25 })}_{0.95}Mn_{0.8 }Co_{0.2}O_3$ The three-phase-boundary length increased with the addition of YSN resulting in the minimum po-larization resistance at 60(LSMC) : 40(YSZ) wt% When LSMC-YSZ compoiste cathodes was sintered at $1200^{\circ}C$ minimum polarization resistance was observed and the capacitace increased with increasing sintering tem-perature.

• Journal of the Korean Vacuum Society
• /
• v.5 no.2
• /
• pp.119-126
• /
• 1996

The effect of the $O_2$ concentration in the sputtering gas mixture, substate temperature and Ar pressure on the structural and optical properties of 3 mol% YSZ and 8 mol% YSZ thin films deposited by RF magnetron sputtering were investigated . The films were observed to have various crystal structures with different compositions in accordance with the type of the target materials. The size of fine grain-like particles decreased wiht increasing the $O_2$ concentration in the sputtering gas in the case of 3mol% YSZ, while it increased in the case of 8 mol% YSZ . However, the average opticla transmission of 8mol% YSZ, despite of thicker thickness. was higher than that of 3 mol% YSZ. Furthermore, the values of refractive index of 3mol% YSZ increased with increasing the $O_2$ concentration in the sputtering gas on the contrary to those of the 8 mol% YSZ. However, the transmission spectra of 8 mol% YSZ films were not strongly influenced by the substrate temperature and Ar pressure, whereas the refractive index of the YSZ films were strongly affected by the sputtering parameters.

• Korean Journal of Materials Research
• /
• v.11 no.4
• /
• pp.283-289
• /
• 2001

Composite cathodes of 50/50 vol% LSM- YSZ (La$_{1-x}$Sr$_{x}$MnO$_3$-yttria stabilized zirconia) were deposited onto surface- Polished YSZ electrolytes by colloidal deposition technique. The cathode characteristics were then examined by scanning electron microscopy (SEM) and X-ray diffraction (XRD) and studied by ac impedance spectroscopy (IS). The typical impedance spectra measured for an air/LSM- YSZ/YSZ/Pt/air cell at $700^{\circ}C$ were composed of two depressed arcs. Addition of YSZ to the LSM electrode significantly enlarged the triple-phase boundaries (TPB) length inside the electrode, which led to a pronounced decrease in cathodic resistivity of LSM-YSZ composite electrodes. Polishing the electrolyte surface to eliminate the influences of surface impurities and to enlarge the TPB length can further reduce cathode resistivity. The cathodic resistivity of the LSM- YSZ electrodes was a strong function of operation temperature, composition and particle size of cathode materials, applied current, and electrolyte surface roughness.

• Applied Chemistry for Engineering
• /
• v.19 no.1
• /
• pp.117-121
• /
• 2008

In this study, thin YSZ film was prepared by electrostatic spray deposition. The morphology of thin film was strongly influenced by precursor solution and substrate temperature. Especially, dense YSZ film was obtained at the substrate temperature of $400^{\circ}C$. The YSZ film growth rate was $12{\mu}m/h $ at the optimum conditions. Product film was characterized by XRD, FE-SEM and EDX.