• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2002년도 하계종합학술대회 논문집(3)
• /
• pp.43-46
• /
• 2002

This paper is about the Micro Accelerometer Sensor that collect the human's writing patterns so as to process its signals. Finally, we pursue the accuracy of digital data about the writing pattern and hope to discuss the possibility of the Micro Accelerometer Sensor Besides, we researched the compensation of signal distortion due to tiIt and analyzed the noise error in order to improve its accuracy.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2004년도 ICCAS
• /
• pp.592-595
• /
• 2004

This paper presents a study on the development of a multi-sensing inertial sensor with a single mechanical structure, which can be used both as a gyroscope and an accelerometer. The proposed MEMS gyro-accelerometer is designed to detect the angular rate and the acceleration at the same time using two separate detection circuits for one proof mass. In this study, the detection and signal processing circuit for an effective signal processing of different inertial measurements is designed, fabricated, and tested. The experimental results show that the performances of the gyro-accelerometer have resolutions of 1mg and 0.025deg/sec and nonlinearities of less than 0.5% for the accelerometer and the gyroscope, respectively, which are similar results with those of sensors with different structures and different detection circuits. The size of the sensor is reduced almost by 50% comparing with the sensors of separated proof mass.

• 인터넷정보학회논문지
• /
• 제11권1호
• /
• pp.129-141
• /
• 2010

본 논문에서는 사람의 행동 모니터링을 위한 멀티 센서 기반의 웨어러블 지능형 디바이스를 제안한다. 다중 행동을 인식하기 위해, 이미지 센서와 가속도 센서를 이용하여 행동 인식 알고리즘을 개발하였다. 멀티 센서로부터 얻은 데이터를 분석하기 위해 그리드 기반 옵티컬 플로우 방법을 제안하고 SVM 분류기법을 이용하였다. 이미지 센서로부터 얻은 모션 벡터의 방향과 크기를 이용하였고, 3축 가속도 센서로부터 얻은 데이터에서 FFT의 축과 크기와의 상관관계를 계산하였다. 실험 결과에서 이미지 센서 기반과 3축 가속도 센서기반의 행동 인식률은 각각 55.57 %, 89.97%를 보였으나 제안한 멀티센서기반의 행동인식률은 92.78% 를 보였다.

• 센서학회지
• /
• 제23권4호
• /
• pp.251-258
• /
• 2014

While the feasibility of vertical velocity as a threshold parameter for pre-impact fall detection has been verified, effects of sensor attachment locations and methods calculating vertical acceleration and velocity on the detection performance have not been studied yet. Regarding the vertical velocity-based pre-impact fall detection, this paper investigates detection accuracies of eight different cases depending on sensor locations (waist vs. sternum), vertical accelerations (accurate acceleration based on both accelerometer and gyroscope vs. approximated acceleration based on only accelerometer), and vertical velocities (velocity with attenuation vs. velocity difference). Test results show that the selection of waist-attached sensor, accurate acceleration, and velocity with attenuation based on accelerometer and gyroscope signals is the best in overall in terms of sensitivity and specificity of the detection as well as lead time.

• Journal of Electrical Engineering and Technology
• /
• 제9권1호
• /
• pp.334-343
• /
• 2014

In this paper, we suggest a method to improve the fusion of an accelerometer and gyro sensor by using a Kalman filter to produce a more high-quality respiration signal to supplement the weakness of using a single accelerometer. To evaluate our proposed algorithm's performance, we developed a chest belt-type module. We performed experiments consisting of aerobic exercise and muscular exercises with 10 subjects. We compared the derived respiration signal from the accelerometer with that from our algorithm using the standard respiration signal from the piezoelectric sensor in the time and frequency domains during the aerobic and muscular exercises. We also analyzed the time delay to verify the synchronization between the output and standard signals. We confirmed that our algorithm improved the respiratory rate's detection accuracy by 4.6% and 9.54% for the treadmill and leg press, respectively, which are dynamic. We also confirmed a small time delay of about 0.638 s on average. We determined that real-time monitoring of the respiration signal is possible. In conclusion, our suggested algorithm can acquire a more high-quality respiration signal in a dynamic exercise environment away from a limited static environment to provide safer and more effective exercises and improve exercise sustainability.

• 한국공간구조학회논문집
• /
• 제16권1호
• /
• pp.85-94
• /
• 2016

In this study, an acceleration sensor that has optical fibers to measure the inclination and acceleration of a structure through contradictory changes in two-component FBG sensors was examined. The proposed method was to ensure precise measurement through the unification of the deformation rate sensor and the angular displacement sensor. A high sensitivity three-axis accelerometer was designed and prepared using this method. To verify the accuracy of the accelerometer, the change in wavelength according to temperature and tension was tested. Then, the change in wavelength of the prepared accelerometer according to the sensor angle, and that of the sensor according to the change in ambient temperature were measured. According to the test results on the FBG-based vibration sensor that was developed using a high-speed vibrator, the range in measurement was 0.7 g or more, wavelength sensitivity, 2150 pm/g or more, and the change in wavelength change, $9.5pm/^{\circ}C$.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2007년도 춘계학술대회논문집
• /
• pp.448-452
• /
• 2007

Many industrial operations require continuous or nearly-continuous operation of machines, which if interrupted can result in significant financial loss. The condition monitoring of these machines has received considerable attention recent years. Rapid developments in semiconductor, computing, and communication with a remote site have led to a new generation of sensor called "smart" sensors which are capable of wireless communication with a remote site. The purpose of this research is the development of smart sensor using which can on-line perform condition monitoring. This system is addressed to detect conditions that may lead to equipment failure when it is running. Moreover it will reduce condition monitoring expense using low cost MEMS accelerometer. This sensor can receive data in real-time or periodic time from MEMS accelerometer. Furthermore, this system is capable for signal preprocessing task (High Pass Filter, Low Pass Filter and Gain Amplifier) and analog to digital converter (A/D) which is controlled by CPU. A/D converter that converts 10bit digital data is used. This sensor communicates with a remote site PC using TCP/IP protocols. Wireless LAN contain IEEE 802.11i-PSK or WPA (PSK, TKIP) encryption. Developed sensor executes performance tests for data acquisition accuracy estimations.

• 비파괴검사학회지
• /
• 제26권6호
• /
• pp.373-379
• /
• 2006

Vibration-based structural health monitoring is one of non-destructive evaluation (NDE) techniques for civil infrastructures. This paper presents a novel fiber optic accelerometer system to monitor civil engineering structures and a successful application of the novel sensor system for measuring ambient vibration of a real building structure. This sensor system integrates the Moire fringe phenomenon with fiber optics to achieve accurate and reliable measurements. The sensor system is immune to electromagnetic (EM) interference making it suitable for difficult applications in such environments involving strong EM fields, electrical spark-induced explosion risks, and cabling problems, prohibiting the use of conventional electromagnetic accelerometers. A prototype sensor system has been developed, together with a signal processing software. The experimental studies demonstrated the high-performance of the fiber optic sensor system. Especially, the sensor was successfully used for monitoring a real building on UCI (University of California Irvine, USA).

• 한국산학기술학회논문지
• /
• 제11권9호
• /
• pp.3184-3189
• /
• 2010

펌프의 성능을 개선하기 위해서는 펌프의 회전수 정보를 획득할 필요성이 있으나, 일반적으로 연료펌프는 연료탱크 안에 내장되어 그 회전수를 측정하기에 어려움이 있다. 연료 펌프의 회전수는 크게 가속도 센서를 이용하는 방법과 전류센서를 이용하는 두 가지 방법이 있다. 가속도 센서를 이용하는 방법은 연료 펌프의 진동수를 측정하여 회전수로 계산하는 방법이며, 전류 센서를 이용하는 방법은 펌프모터의 주기적 전압방출 특성을 이용하여 회전수를 계산하는 방법이다. 본 연구에서는 전류센서를 가속도 센서와 동시에 장착하여 다양한 측정 조건에 대한 실험을 수행하였다. 결론적으로 전류센서로도 연료펌프의 회전수를 정밀하게 측정하는 것이 가능하였으며 특히 낮은 회전수 영역에서는 가속도센서 대비 강건한 계측특성을 보였다. 오차 1% 이내의 회전수를 측정하기위하여, 가속도센서는 데이터 저장간격 0.5Hz 이하의 설정이 필요하였으며, 전류센서는 데이터 저장간격 2.0Hz이하의 설정이 필요하였다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2008년도 추계학술대회A
• /
• pp.1951-1956
• /
• 2008

Various MEMS accelerometers are used in engineering applications including automobiles, mobile phones, military systems, and electronic devices. Among them, the thermal accelerometer employing the temperature difference induced by the convective flow inside the micro cavity has been a topic of interest. As the convective sensor does not utilize a solid proof mass, it is compact, lightweight, inexpensive to manufacture, sensitive and highly endurable to mechanical shock. However, the complexity of the convective flow and various design constraints make optimization of a device a crucial step before fabrication. In this work, optimization of a 2-axis thermal convective MEMS accelerometer is conducted based on 3-dimensional numerical simulation. Parametric studies are performed by varying the several design variables such as the heater shape/size, the cavity size and types of the gas medium and the position of temperature probes in the sensor. The results of optimal design are presented.