• 한국세라믹학회지
• /
• 제43권10호
• /
• pp.635-639
• /
• 2006

Dispersion behavior of the slurries consisted of Pb or Bi-based glass frits, which are used for the fabrication of green sheet as PDP front panel transparent dielectric, was examined in non-aqueous solvent system. Measurements of sedimentation height and viscosity were conducted to determine proper dispersion condition in the various solvent and dispersant system. Azotropic compound and ethyl acetate were used as the solvent and ammonium-type dispersant was applied to the slurries. All slurries were dispersed well in azotropic solvent system involving 20$\sim$50 vol% ethyl acetate at 2$\sim$3 wt% dispersant content. Especially, dispersion behavior was notably improved in the addition of ethyl acetate in the Bi-based frit slurry.

• 한국재료학회지
• /
• 제26권3호
• /
• pp.109-116
• /
• 2016

To achieve the fabrication of high-quality Ag-coated Cu particles through a wet chemical process, we reported herein pretreatment conditions using an ammonium-based mixed solvent for the removal of a $Cu_2O$ layer on Cu particles that were oxidized in air for 1 hr at $200^{\circ}C$ or for 3 days at room temperature. Furthermore, we discussed the results of post-Ag plating with respect to removal level of the oxide layer. X-ray diffraction results revealed that the removal rate of the oxide layer is directly proportional to the concentration of the pretreatment solvent. With the results of Auger electron spectroscopy using oxidized Cu plates, the concentrations required to completely remove 50-nm-thick and 2-nm-thick oxides within 5 min were determined to be X2.5 and X0.13. However, the optimal concentrations in an actual Ag plating process using Cu powder increased to X0.4 and X0.5, respectively, because the oxidation in powder may be accelerated and the complete removal of oxide should be tuned to the thickest oxide layer among all the particles. Back-scattered electron images showed the formation of pure fine Ag particles instead of a uniform and smooth Ag coating in the Ag plating performed after incomplete removal of the oxide layer, indicating that the remaining oxide layer obstructs heterogeneous nucleation and plating by reduced Ag atoms.

• 대한약학회:학술대회논문집
• /
• 대한약학회 2003년도 Proceedings of the Convention of the Pharmaceutical Society of Korea Vol.1
• /
• pp.297.1-297.1
• /
• 2003

Organic solvent-based enteric coating technology using hydroxypropyl methylcellulose phthalate (HPMCP) has been developed for many years due to low water solubility of HPMCP. In this work, aqueous HPMCP nanoparticles (HPMCP-NPs) were prepared by neutralization emulsification method using HPMCP powder and ammonium hydroxide (NH40H) in the absence of any organic solvent and emulsifier. (omitted)

• Bulletin of the Korean Chemical Society
• /
• 제32권7호
• /
• pp.2243-2248
• /
• 2011

Carbon-based solid acid catalyst was found to be highly efficient, eco-friendly and recyclable heterogeneous catalyst for the multicomponent reaction of dimedone, aromatic aldehydes, and a nitrogen source (ammonium acetate or aromatic amines) under solvent-free conditions, giving rise to 1,8-dioxodecahydroacridines in high yields. The present methodology offers several advantages, such as a simple procedure with an easy work-up, short reaction times, high yields, and the absence of any volatile and hazardous organic solvents.

• 한국응용과학기술학회지
• /
• 제37권6호
• /
• pp.1619-1626
• /
• 2020

본 연구에서는 폴리인산암모늄 인산염과 HMDI로 합성된 수분산 폴리우레탄수지의 물리적 특성을 필름 시료와 피혁(Full-Grain) 표면에 코팅을 하여 물리적 특성 변화를 연구하였다. 내용제성은 모든 시료에서 변확 없음을 확인 할수 있었으며, 인장강도의 경우 폴리인산암모늄이 가장 많이 함유된 DPU-AP3(1.887 kgf/㎟)가 가장 낮은 물성을 보였다. 연실율은 폴리인산암모늄 많이 함유된 시료가 548%로 측정되었다. 내마모성은 폴리인산암모늄이 많이 함유된 시료가 548 mg.loss로 측정되어 폴리인산 암모늄과 수분산 폴리우레탄의 블랜딩된 수지의 물성변화가 확인되었다.

• Mass Spectrometry Letters
• /
• 제8권3호
• /
• pp.59-64
• /
• 2017

In clinical diagnosis, it's well known that the abnormal level of uric acid (UA) in human body is implicated in diverse human diseases, for instance, chronic heart failure, gouty arthritis, diabetes, and so on. As a primary method, an isotope dilution mass spectrometry (IDMS) has been used to obtain the accurate quantity of UA in blood or serum and also develop the certificated reference material (CRM) so as to provide a SI-traceability to clinical laboratories. Due to the low solubility of UA in water, an ammonium hydroxide ($NH_4OH$) has been considered as a promising solvent to increase the solubility of UA that enables the preparation of both UA and its isotope standard solution for next IDMS-based absolute quantification. But, because of using this $NH_4OH$ solvent, it gives rise to the unwanted degradation of UA. In this study, we sought to optimize condition for the stability of UA in $NH_4OH$ solution by varying the mole ratios of UA to $NH_4OH$, followed by ID-LC-MRM analysis. In addition, we also inspected minutely the effect of the storage temperatures. Additionally, we also performed the quantitative analysis of UA in the KRISS serum certificated reference material (CRM, 111-01-02A) with diverse mixing ratios of UA to $NH_4OH$ and then compared those values to its certification value. Based on our experiments, adjusting the mole ratio of 1/2 ($UA/NH_4OH$) with the storage temperature of $-20^{\circ}C$ is an effective way to secure both the solubility and stability of UA in $NH_4OH$ solution for next IDMS-based quantification of UA in serum.

• Journal of Electrochemical Science and Technology
• /
• 제5권4호
• /
• pp.95-104
• /
• 2014

Electrochemical performance of Li-ion cells with $LiMn_2O_4$ cathodes and graphite anodes with carbonates electrolytes containing quaternary ammonium-based room temperature ionic liquids (ILs) is investigated. Eight different ILs based on tetraalkylammonium, pyrrolidinium or piperidinium cations paired with bis(trifluoromethylsulfonyl)imide or tris(pentafluoroethyl)trifluorophosphate anions are examined in combination with dimethyl carbonate as a main solvent and fluoroethylene carbonate as a solid electrolyte interface forming agent. It is shown that cycling properties of the cells are strongly affected by the content of ILs in the electrolyte mixtures and its increase corresponds to lower discharge capacity retention. Since viscosity and conductivity of ILs are of a great importance for the electrolytes formulation, some kind of combined parameter should be used for the assessment of IL applicability and calculated values of Walden products for neat ILs represent one of the possible options. Besides, positive effect of ILs on reduction of flammability and enhancement of thermal stability of electrolytes in contact with charged electrodes have been demonstrated by means of self-extinguishing time test and differential scanning calorimetry respectively.

• Nuclear Engineering and Technology
• /
• 제51권7호
• /
• pp.1799-1804
• /
• 2019

The concept of a new method, the CARBEX (CARBonate EXtraction) process, was proposed for reprocessing of spent uranium oxide fuel. The proposed process is based on use of water solutions of $Na_2CO_3$ or $(NH_4)_2CO_3$ and solvent extraction (SE) by the quaternary ammonium compounds for selective recovery and purification of U from the fission products (FPs). Applying of SE allows to reach high degree of purification of U from FPs. Carrying out the processes in poorly aggressive alkaline carbonate media leads to increasing safety of SNF's reprocessing and better selectivity of separation of lanthanides and actinides. Moreover carbonate reprocessing media allows to carry out a recycling and regeneration of reagents. We have been done laboratory scale experiments on the extraction components of simulated voloxidated spent fuel in the solutions of NaOH or $Na_2CO_3-H_2O_2$ and recovery of U from carbonate solutions by SE method using carbonate of methyltrioctylammonium in toluene. It was shown that the purification factors of U from impurities of simulated FPs reached values $10^3-10^5$. The received results support our opinion that CARBEX after the further development can become more safe, simple and profitable method of spent fuel reprocessing.

• Bulletin of the Korean Chemical Society
• /
• 제25권1호
• /
• pp.59-62
• /
• 2004

The ammonium ion-selective electrodes ($NH^+_4$-ISEs) based on the tetrahydrofuran(THF)-containing-16-crown-4 derivatives,1,4,6,9,11,14,16,19-tetraoxocycloeicosane ($L^1$) and 5,10,15,20,-tetramethyl-1,4,6,9,11,14,16,19-tetraoxocycloeicosane ($L^2$), were prepared and the electrode characteristics were tested. The conditioned $NH_4^+$-ISEs (E1) based on $L^1$ with TEHP as a plasticising solvent mediator gave best results with near-Nernstian slope of 53.9 mV/decade of activity, detection limit of $10^{-4.9}$ M, and enhanced selectivity coefficients for the $NH^+_4$ ion with respect to an interfering $K^+$ ion (log $K^{pot}_{NH_4^+,K^+}$ = -1.84). This result was compared to other ammonium ionophores reported previously, for example, that of nonactin (log $K^{pot}_{NH_4^+,K^+}$ = -0.92). The proposed electrode showed no significant potential changes in the range of 3.0 < pH < 9.0.

• 공업화학
• /
• 제7권3호
• /
• pp.536-542
• /
• 1996

본 연구에서는 유화중합을 통해 water jet loom용 경사 호제인 비용제형 수용성 아크릴 호제(GSW-7000)를 합성하였다. 이 호제는 아크릴계 호제의 암모늄염 형태로 제조되어 weaving force에 대한 저항력과 water jet loom 사용에 있어 물에 대한 저항력이 우수하였다. 제조한 GSW-7000은 sizing에 적당한 점도를 가지고 있고, 신도와 접착력, 용해성, 침투성 및 호부착성이 우수하였다. 또한 본 호제로 처리된 호부사는 접착강도가 높아 기존 용제형 아크릴 호제에 비하여 sizing시 호제 소모량을 70~80% 수준으로 저하시켜도 우수한 집속성 및 포합력을 나타내었으며, 호피막이 유연하며 평활성 및 내마모성이 우수하여 호부시 유제 및 대전 방지제를 사용하지 않아도 sizing 및 제직이 가능하였다.