• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1995년도 추계학술대회 논문집
• /
• pp.995-999
• /
• 1995

In spindle-bearing system, the displacement characteristics of the bearing by the load applied on the spindle are affected greatly by the assembling tolerance between the spindle and housing assembled to support the bearing. Also in spindle system of rotational operation, the compliance characteristic of the bearing is expected to be varied frequently by the thermal deformation of the spindle and the housing. To predict the thermal deformation of the spindle including heat generation of the bearing, we need to examine the effect on the compliance of spindle-bearing system by the assembling tolerance. In this paper, we proposed the load-displacement relation expression considering the effect which the variation of contact pressure due to the radial directional assembling tolerance between the bearing and the housing influences on the axial and radial directional displacement characteristics of the bearing. Furthermore, for several assembling systems of bearings and housings having all different assembling tolerances, we proposed a method to predict exactly the variation of the bearing preload which is sensitive to the thermal deformation by showing the propriety with experimental results.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2001년도 춘계학술대회논문집
• /
• pp.718-721
• /
• 2001

For higher recording density in optical data storage, near field optics is being actively researched as one of the promising alternatives. But the tight assembling tolerance in NFR is one of big barriers to overcome for the realization of it. In this paper, the tolerances in assembling optic components of NFR system are analyzed. Some of key tolerances can be loosened by the optimization of objective lens design. But one of them become too tight by the optimization and should be controlled by other means. One of possible methods to control the tolerance is discussed.

• 항공우주시스템공학회지
• /
• 제11권4호
• /
• pp.48-53
• /
• 2017

액체로켓엔진은 연소기, 터보펌프, 가스발생기, 각종 밸브 및 배관, 조인트, 오리피스, 튜브, 하니스, 센서 등이 결합되어있는 매우 복잡한 시스템이다. 대부분의 액체로켓엔진 부품은 IT(ISO Tolerance) 기준으로 6등급 이상의 높은 정밀도를 요구하며 정상운용 전후 시동과 종료 등과 같은 비정상 시의 응답에도 대응해야한다. 따라서 엔진 시스템 및 부품은 넓은 영역에서 안정적으로 동작할 수 있도록 설계되어야하며 조립은 이러한 설계철학을 충실히 반영하여야 한다. 엔진 설계 시에는 부품 간에 물리적 혹은 기능적 간섭이 없도록 공간배치를 해야 하며 조립 중 조립성과 조립 후 유지보수의 효율성까지도 고려되어야 한다. 특히 양산품이 아닌 개발 단계에서는 조립 중 부품 간 공차의 누적, 각종 구성품의 비정렬, 부품 인터페이스 간의 불일치 등이 발생할 수 있다. 즉, 엔진조립공정은 개발 중 내재되어있는 각종 위험이 현실화 되는 위기 혹은 예상치 못한 사건(incident)이 발생하기 쉬운 작업이다. 그러므로 조립 중 사건이 발생했을 경우를 대비한 신속한 대응시스템이 구비되어야한다. 이 연구에서는 위에서 언급한 사항들의 기본적 대응방법과 한국형발사체에 탑재되는 7 tonf 급 엔진의 실제 조립공정을 다루었다.

• 정보저장시스템학회:학술대회논문집
• /
• 정보저장시스템학회 2005년도 추계학술대회 논문집
• /
• pp.2-3
• /
• 2005

Air gap control method using a conventional actuator for near field recording technology has been reported. To achieve good performance in the air gap servo and further experiments, the assembling between OL and SIL is the critical procedure. A lens set with NA 1.45 at 405 m has been assembled and tested by using a Twyman-Green interferometer. The tolerance of assembling is very tight and the designing and adjusting procedure must be carefully controlled.

• 대한안전경영과학회:학술대회논문집
• /
• 대한안전경영과학회 2008년도 춘계학술대회
• /
• pp.417-428
• /
• 2008

Designers have to consider voice of customer, process capability, manufacturing standards & condition, manufacturing method, characteristics of products to decide tolerances. Especially, in case of position of hole and pin, designers have to consider process capability to decide tolerances. The traditional position tolerances used in a drawing are theoretical values which are allocated to position under the worst case assembling condition that both hole and pin are the maximum material condition(MMC). However, When the process capability is high, more exact product size can be produced under stable manufacturing condition. larger clearance of hole and pin can be allocated. In this point of view, manufacturer could increase the yield by allocating larger position tolerance than theoretical position tolerance of hole and pin considering process capability.

• 대한안전경영과학회지
• /
• 제11권1호
• /
• pp.75-85
• /
• 2009

Designers have to consider voice of customer, process capability, manufacturing standards & condition, manufacturing method and characteristics of products to decide tolerances. Especially, in case of position of hole and pin, designers have to consider process capability to decide tolerances. The traditional position tolerances used in a drawing are theoretical values which are allocated to position under the worst case assembling condition that both hole and pin are the maximum material condition(MMC). However, when the process capability is high, more exact product size can be produced under stable manufacturing condition. Larger clearance of hole and pin can be allocated. In this point of view, manufacturer could increase the yield by allocating larger position tolerance than theoretical position tolerance of hole and pin considering process capability.

• 한국정밀공학회지
• /
• 제14권1호
• /
• pp.90-100
• /
• 1997

Sppur gear trains are used widely in high precision machines because gear trains have an advantage of exact transmission of angular velocity. Especially, gear trains are used in high quali8ty photocopying and photography OA machines. In general, gears have errors in manufacturing and assembling process and the errors are limited by tolerances. As the result, the tolerances cause the performance error. Therfore, it is important to predict transmission error caused by the tolerances for the tolerance design. Earlier tolerance design methods use mainly experimental and geometrical techniques. In this paper, a method for gear train analysis with tolerance is proposed. Because the method uses dynamic contacts, it is possible to consider irregularities and assemble errors of gears. In addition, the method can predit dynamic loads on the teeth of gears.

• 한국정밀공학회지
• /
• 제21권2호
• /
• pp.92-99
• /
• 2004

The errors can cause the serious loss of the performance of a precision machine system. In this paper, we proposed the method of allocating the alignment tolerances of the parts and applied this method to get the optimal tolerances of a Confocal Scanning Microscope. In general, tight tolerances are required to maintain the performance of a system, but a high cost of manufacturing and assembling is required to preserve the tight tolerances. The purpose of allocating the optimal tolerances is minimizing the cost while keeping the high performance of the system. In the optimal problem, we maximized the tolerances while maintaining the performance requirements. The Monte Carlo Method, a statistical simulation method, is used in tolerance analysis. Alignment tolerances of optical components of the confocal scanning microscope are optimized to minimize the cost and to maintain the observation performance of the microscope. We can also apply this method to the other precision machine system.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2021년도 봄 학술논문 발표대회
• /
• pp.12-13
• /
• 2021

Methods for the manufacture, erection, and assembly of heavy frame modules were proposed. Interferences among precast members were prevented by using bolted metal plates for dry precast beam-to-column joints during assembly with a clearance for tolerance implementing grouted concrete filler plates instead of metal filler plates. Clearances for tolerances were provided to avoid conflictions among components during erection phases. These gaps were, then, grouted by high-strength mortar. The constructability of new connections of a beam-to-column joint using bolted metal plates for precast structures was examined using a full-scale assembly test in which practical observations indicated that members could be aligned and placed accurately in both horizontal and vertical directions, leading to a fast and convenient assembling. Bolt holes of the endplate were properly aligned using couplers with 30 mm fastened length embedded in the columns. The assembly test demonstrated the erection safety and structural stability of the proposed joints that were without filler plates when they were subjected to heavy loads at the time of their erection. The facile and rapid assembly of precast beam-to-column connections with a 30 mm tolerance was observed. The proposed assembly method is rapid, sustainable, and resilient, replacing the conventional methods of concrete frame construction, offering a connection that can be used in constructing infrastructure, such as buildings and pipe-rack frames.

• 천문학회보
• /
• 제40권2호
• /
• pp.56.4-57
• /
• 2015

We present the optical design and a sensitivity analysis for a wide field of view (FOV) instrument operating at UV and IR wavelengths. The ongoing investigation is performed in collaboration with Omnisys Instruments (Sweden) and focuses on a telluric-limb-viewing instrument that will fly in a low Earth orbit to study mesospheric wave structures over a wide range of horizontal scales in the altitude range 80 - 100 km. The instrument has six wavelength channels which consist of 4 channels of IR and 2 of UV. We are proposing an optical design based on three mirror aplanatic off-axis reflective system. The entrance pupil diameter and effective focal length are 45 mm and 270 mm, respectively. The FOV is $5.5^{\circ}{\times}1^{\circ}$ and the secondary mirror is set for stop. The optical specification is required to have an encircled energy of at least 80 % within a diameter of 21 um. We performed sensitivity analysis for the longest wavelength of 772 nm in consideration of the diffraction limit of system. The results show that tolerance limits for positions and angles of the mirrors are not very sensitive compared with typical error budgets of manufacturing and assembling process. The secondary mirror has the most sensitive tolerance for surface figure of 250 nm in root-mean-square.