• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2010.11a
• /
• pp.239-240
• /
• 2010

• Journal of Biosystems Engineering
• /
• v.26 no.4
• /
• pp.337-354
• /
• 2001

This study was conducted in order to develop a Chinese cabbage harvester attachable to tractors. For designing Chinese cabbage harvester in which laboratory and field tests were conducted with to determine feasible values design factors. To adopt the various sizer of C-cabbages, U-type soft rubber band was attached to the chain conveyor with an angle. Required torque of the conveyor axle was about 206-210kgf$.$cm. And the required peripheral speed of the disk cutter was 6.54m/s or more to have a clean session in root cutting. Three different harvest method were tested. The best harvesting method with minimum pulling force and damage was disk cutting flying just above the soil surface were the cut chinese cabbages are transferring to the holding conveyor attached soft rubber lug in prompt. Theoretical speed ratio of the tractor travel and feed of a chain conveyor was 1:1.2 with the attaching angle of 30 degree and 1:1.1 with the angle of 20 degree. Actual field experiment showed the speed ratio of 1:1.5 was the best because of the slip effect.

• Korean Journal of Agricultural Science
• /
• v.37 no.2
• /
• pp.309-314
• /
• 2010

Bale is an operation of collecting livestock feed materials from field crop residue, and mechanization demand on the operation has been increased. Bailers imported from foreign countries such as Japan and European countries have been used, but those models showed improper performance in Korean situations. In recent years, a steel-roller type round baler attachable to medium size tractors(40 to 60 HP) for effective bale operation in Korea was developed. This study was conducted to evaluate field performance of the baler. For proper baling operation, engine speed was greater than 1,800rpm, average traction force and PTO torque were about 4kN and in a range of 380-671Nm, and maximum values were about 7kN and 3,000Nm, respectively. Performance evaluation tests for sudan grass, rice straw, and blue barley showed that field capacity was 0.59ha/h for blue barley and 0.99ha/h for sudan grass and rice straw. Bale weight, diameter, width, and bulk density were in ranges of 176.1~418.4kg, 1.07~1.12m, 1.02~1.04m, and 175.3~454.1kg/$m^3$. Noise sound level during the baling operation was 4dB greater than idle operation condition, which was considered to be ignorant.

• Journal of the Korean Society for Precision Engineering
• /
• v.19 no.1
• /
• pp.143-149
• /
• 2002

Robot are necessary to automate the work on a vertical plane of work piece to produce a large structure like a ship, so that a permanent magnet wheel has been attempted to be used for a mobile robot. Its adhesive power was enhanced by restricting the occurrence direction of magnetic flow. Furthermore a method which weakened the adhesive force was developed for easy detachement of the wheel by changing magnetic flow with metal pin. To measure the characteristics of the adhesive and detaching farces, a load call and a gaussmeter were used. The result showed that the adhesive power was reduced to 1/3 of normal state by using 4 inducing pins.

• Journal of electromagnetic engineering and science
• /
• v.18 no.1
• /
• pp.7-12
• /
• 2018

This article proposes an ultrahigh frequency band radio frequency identification (RFID) tag antenna for drug runout management that can be used in hospitals. The RFID tag antenna is designed to function as a sensor that alerts drug runout when a drug inside a drip chamber is completely consumed but does not work when a drug remains inside a drop chamber. A previously proposed 915 MHz dipole antenna, is too large to be attached to the drip chamber of a feeding bag. Moreover, the length of the dipole (L) should be increased for conjugate matching with an RFID chip. Therefore, the dipole antenna is downsized so that it can be attached to the drip chamber through a fine meander line structure coupling with a corrugate meander line. A transparent cover is added to enhance the grip force between the designed antenna and the drip chamber and to enable detachment. The dimensions of the completed antenna structure attachable to a drip chamber are 32.59 mm (height) and 13.5 mm (width). The gain reduction due to the decreased antenna length is enhanced. The fabricated antenna shows an average omni-directional read range of 10.65 m on a horizontal plane and has the function of sensing the presence of a drug.

• Journal of Biosystems Engineering
• /
• v.26 no.1
• /
• pp.1-10
• /
• 2001

Interactions between cage wheel and soil under the wet paddy field condition were analyzed. The cage wheel as a traction aid to driving tires of tractor was attached to the outside of the tires. The driving torque transmitted only to the cage wheel was measured and its effect on the total driving torque by both the tires and cage wheel was analyzed. Mathematical models were developed to predict the soil thrusts y a single lug and by the cage wheel with many lugs, respectively. Experimental results showed that as the diameter of cage wheel increased, positive effects of the cage wheel on the traction also increased. About 33-40% of the total traction force was obtained by the cage wheel with a diameter 1,182mm and 49-55% with a diameter 1,222mm. The peak thrust of the single lug of cage wheel increased by 31% and 59%, respectively when the diameter of the cage wheel increased from 1,182mm to 1,222mm and 1,262mm. The thrust by the cage wheel was estimated by using the developed mathematical models and the results were proved that the models are reliable for the estimation of the traction by the cage wheels.

• Journal of Adhesion and Interface
• /
• v.5 no.2
• /
• pp.22-36
• /
• 2004

Several in-situ testing methods of adhesively bonded joints under static short-time tensile loading are critically analyzed in terms of experimental procedure and data evaluation. Due to its rather homogeneous stress state across the glue line, the tensile-shear test with thick single-lap specimens, according to ISO 11003-2, has become the most important test process for the determination of realistic materials parameters. This basic method, which was improved in both, the experimental part by stepped adherends and easily attachable extensometers and the evaluation procedure by numeric substrate deformation correction and test simulation based on the finite element method (FEM), is therefore demonstrated by application to several kinds of adhesives and metallic adherends. Multi-axial load decreases the strength of a joint. This effect, which is illustrated by an experimental comparison, impedes the derivation of realistic mechanical characteristics from measured force-displacement curves. It is shown by numeric modeling that tensile-shear tests with thin plate substrates according to ISO 4587, which are widely used for quick industrial quality assurance, reveal an inhomogeneous stress state, especially because of relatively large adherend deformation. Complete experimental determination of the elastic properties of bonded joints requires independent measurement of at least two characteristics. As the thick-adherend tensile-shear test directly yields the shear modulus, the tensile butt-joint test according to ISO 6922 represents the most obvious complement of the test programme. Thus, validity of analytical correction formulae proposed in literature for the derivation of realistic materials characteristics is verified by numeric simulation. Moreover, the influence of the substrate deformation is examined and a FEM correction method introduced.