• 한국재료학회지
• /
• 제29권4호
• /
• pp.233-240
• /
• 2019

This study analyzes the mechanical properties, including the attrition rate, of $50{\mu}m$ size yttria-stabilized zirconia (YSZ) beads with different microstructures and high-energy milling conditions. The yttria distribution in the grain and grain-boundary of the fully sintered beads relates closely to Vickers hardness and the attrition rate of the YSZ beads. Grain size, fractured surfaces, and yttrium distribution are analyzed by electronic microscopes. For standardization and a reliable comparison of the attrition rate of zirconia beads with different conditions, Zr content in milled ceramic powder is analyzed and calculated by X-ray Fluorescence Spectrometer(XRF) instead of directly measuring the weight change of milled YSZ beads. The beads with small grain sizes sintered at lower temperature exhibit a higher Vickers hardness and lower attrition rate. The attrition rate of $50{\mu}m$ YSZ beads is measured and compared with the various materials properties of ceramic powders used for high-energy milling. The attrition rate of beads appears to be closely related to the Vickers hardness of ceramic materials used for milling, and demonstrates more than a 10 times higher attrition rate with Alumina(Hv ~1650) powder than $BaTiO_3$ powder (Hv ~315).

• 한국수소및신에너지학회논문집
• /
• 제24권5호
• /
• pp.428-436
• /
• 2013

Attrition characteristics of $CO_2$ absorbents for pre-combustion $CO_2$ capture were investigated to check attrition loss of those absorbents and to determine solid circulation direction and the better $CO_2$ absorbent. The cumulative attrition losses of two absorbents increased with increasing time. However, attrition loss under a humidified condition was lower than that under a non-humidified condition case. Between two absorbents, attrition loss of PKM1-SU absorbent was higher than that of P4-600 absorbent. The average particle sizes of the attrited particles were less than $2.5{\mu}m$ for two absorbents under a non-humidified condition case, and therefore, we could conclude that the main mechanism of attrition for two absorbents is not fragmentation but abrasion. Based on the results from the test for the effect of humidity on the attrition loss, we selected solid circulation direction from SEWGS reactor to regeneration reactor because the SEWGS reactor contains more water vapor than regeneration reactor. Attrition loss and make-up rate of two absorbents were compared based on the results from $CO_2$ sorption capacity tests and attrition tests. Required make-up rate of P4-600 absorbent was lower than that of PKM1-SU absorbent. However, more detail investigation on the optimum regeneration temperature, manufacturing cost, solid circulation rate, regeneration rate, and long-term sorption capacity should be considered to select the best $CO_2$ absorbent.

• 대한치과기공학회지
• /
• 제19권1호
• /
• pp.121-130
• /
• 1997

This study was aimed to help the construction of naturally dental prosthesis by investigation of the factors affecting on the attrition position and attrition angle of maxillary canines. Therefore 163 complete cast of maxillary and mandibular extracted from the student of K. college were subjected for this study, and result through the study are as follows. 1. None attrite rate of the maxillary canine was 7%, of examined teeth. 2. Throughout mesiodistal attrition of 1) Throughout mesiodistal attrition area of the maxillary canines showed that mesial area and mid area of cusp was more frequence in attrition than distal area of it. 2) Sex, dental arch type, vertical overlap, horizontal overlap, did not affect significantly to throughtout mesiodistal attrition statistically 3. Througout labiolingual attrition area 1) Throughout labiolingual attrition area of the maxillary canines showed that attrition of the from lingual to labioncisal edge was more frequence than it of linguoincisal edge 2) It showed that attrition of the from lingual to labioincisal edge was more frequence when the length of horizontal overlap is shorter, by horizontal overlap 3) The attrition of the from lingual to labioincisal edge in maxillary left canines showed that male was more frequence in attrition than female. 4) Dental arch type, vertical overlap, did not affect signioficantly to labiolingual attrition, statistically. 4. Attrition angle 1) It showed that average attrition angle of the maxillary right canines were $19{\pm}11.02$ dagree, and it of left canines were $18{\pm}11.83$ degree. 2) It showed that famale have a bigger attrition angle than male, by sex. 3) It showed that attrition angle was bigger when the length of horizontal ovelap is bigger, by horizontal overlap.

• 공업화학
• /
• 제17권5호
• /
• pp.547-551
• /
• 2006

ASTM D5757-95에 따른 입자 마모 측정기와 lab-scale 유동층 연소로에서 국내 무연탄 회재와 모래의 입자 마모 특성을 실험하였다. 기체유속에 따른 마모 특성으로 비산 회재의 입도 분포, 마모 속도, 마모율 등을 측정하였다. 일반적으로 유동층 층물질로 사용되는 모래보다 회재가 마모에 취약해 비산 회재의 발생이 높았으며 마모지수의 경우 5배 정도 높게 나타났다. 기체 유속 변화에 따라 입자의 마모에 의해 미세 입자의 생성이 지속적으로 발생하였으며 다음과 같은 식을 따른다. $$\frac{dW}{dt}=-3.18{\times}10^{-7}(U-U_{mf})W$$.

• 대한치과기공학회지
• /
• 제18권1호
• /
• pp.117-127
• /
• 1996

This study was aimed to help the construction of esthetic dental prosthesis by investigation of the factors affecting on the atterition position and attrition angle of maxillary lateral incisors. Therefore 197 complete cast of maxillary and mandibualar extracted form the student of K. college were subjected for this study, and result throught the study are as follows. 1. None attrite rate of the maxiilary right lateral incisors was about 16.2% and that of the maxillary left lateral incisors was about 32.4% of examined teeth. 2. Throught mesiodistal attrition area 1) It showed that right lateral incisors was the most frequence in attrition of mesial area of incisal edge, and left lateral incisors was the most frequence in attrition of mesial and mid area of incisal edge. 2) It showed that square type arch was more frequence in attrition of all incisal edge, and ovoid type arch was more frequence in the attrition of mid area of incisal edge, and ovoid type arch was more frequence in the attrition of mid area of incisal edge, and taper type arch was more frequence in the attrition of mesial area of incisal edge than it of average frequence of right lateral incisors, by dental arch type. 3) It showed that square type arch was more frequence in the attrition of all area and mid area of incisal edge, and ovoid type arch was more frequence in the attrition of mid area of incisal edge, and taper type arch was more frequence in the attrition of mesial and distal area of incisal edge than it of average frequence of left lateral incisal, by dental arch type. 4) Sex, vertical overlap, horizontal overlap, incisal guide angle, did not affect significantly to throughout mesiodistal attrition, statistically 3. Throughout labiolingual attrition quantity. 1) It showed that throughout labiolingual attrition quantity was more attrition in order of taper type arch < ovoid type arch < square type arch, by dental arch type. 2) It showed that throughout labiolingual attrition qauntity was more attrition when the length of horizontal overlap is shorter than it of other, by horizontal overlap. 3) Throughout labiolingual attrition quantity of right lateral incisors showed that male was more attrition than it of female. 4) Vertical overlap, incisal guide angle, sex on left lateral incisors did not affect significantly to throughout labiolingual attrition, statistically. 4. Attrition angle 1) It showed that average attrition anlge of right lateral incisors were $30{\pm}13.02$ degree, and it of left lateral incisors were $26{\pm}13.37$ degree. 2) It showed that taper type arch have a bigger attrition angle than it of average of lateral incisors, and square tape arch have a smaller attrition angle than it of average of lateral incisors, by dental arch type. 3) It showed that horizontal overlap of 2.1mm above have a bigger attrition angle than it of average, by horizontal overlap. 4) It showed that female have a bigger attrition angle it of male, by sex.

• 경영과학
• /
• 제26권3호
• /
• pp.11-21
• /
• 2009

In this paper, we proposed some valuable analysis results of cultivation campaign marketing in A mobile telephone company. The cultivation campaign marketing is a new outbound TM campaign strategy composed of 4 steps for new subscribers. During the analyses, attrition rate of A mobile company, outbound TM rejection rate, contact rate/call success rate and additional service attrition rate after subscription are measured as an effect of cultivation campaign. The results showed that there were no statistical significance in improving retention rate between customers experienced 4 step cultivation campaign and control group. However, the cultivation campaign had a better effect on improving response rate and success of selling additional service product of mobile company compared to general selling campaign. This is because cultivation campaign group had been taking care of from subscription time. It is suggested that cultivation campaign had better confined customers more likely to buy additional service to outbound TM for the sake of financial efficiency.

• 공업화학
• /
• 제19권3호
• /
• pp.295-298
• /
• 2008

ASTM D5757-95에 따른 입자 마모 측정기를 이용하여 접선 방향의 기체 주입에 따른 입자 마모 특성을 고찰하였다. 접선 방향의 기체 주입에 따른 영향을 고찰하기 위하여 모래의 입도 분포 변화, 비산 회재의 양 등을 측정하여 비교하였다. 입자 마모에 따라서 발생하는 미세 입자들은 기체 유속이 증가함에 따라서 증가하였다. 수직 방향의 기체 주입에 비해 접선 방향으로 기체를 주입함에 따라서 입자 마모량이 변하였으며 노즐의 각도가 감소함에 따라서 비산량이 줄어들었다. 또한 전체 유량이 동일한 경우, 사용되는 노즐이 증가할수록 입도변화가 커짐도 알 수 있었다.

• 한국수소및신에너지학회논문집
• /
• 제15권3호
• /
• pp.208-219
• /
• 2004

To find a suitable oxygen carrier particle for a 50kW chemical-looping combustor, which was designed and installed to demonstrate continuous oxidation and reduction, three oxygen carrier particles(NiO/bentonite, $NiO/NiAl_2O_4$, $CoO_x/CoAl_2O_4$) were prepared. The reactivity and the attrition resistance of particles were measured and investigated by a thermo-gravimetrical analyzer and an attrition test apparatus respectively. From the viewpoints of oxygen transfer capacity, optimum reaction temperature(operating temperature range), reaction rate, carbon deposition rate, and attrition resistance, NiO/bentonite particle showed better performance than the other particles, therefore we selected NiO/bentonite particle as an optimum oxygen carrier particle.

• 한국국방경영분석학회지
• /
• 제28권2호
• /
• pp.70-84
• /
• 2002

This paper deals with the attrition rate of major facility such as a particular building that is one of the most important target in the war time. In order to estimate the attrition rate, we use JAWS, WinJMEM which are programed by JTCG/ME of AMSAA and spreadsheet package which is able to assist the limitation of those programs and calculate all the procedure of this computation. This method uses the effectiveness index(El) which indicates the numerical measure of the effectiveness of a given weapon of a given target. The range error probable(REP) and the deflection error probable(DEP) in the ground plane also should be used. Those mean the measure of delivery accuracy of the weapon system. In this paper, it is improved that the El can be obtained from the regression analysis using the weight of the warhead explosive as the independent variable. It implies that we are able to obtain the El and the conditional probability of damage of the enemy weapon. After that, the single-sortie probability of damage can be computed using WinJMEM or another assistant program such as the spreadsheet package which shows the result immediately.

• 공업화학
• /
• 제16권5호
• /
• pp.603-608
• /
• 2005

본 연구는 zinc titanate를 탈황제로 사용하는 유동층 탈황공정에서 고체 입자 마모특성을 고찰하는 것을 목표로 내경 0.035 m, 높이 1.34 m의 기체유동층 실험장치에서 수행되었다. 다공판 분배기에서 고속 분사 제트와 유동층 내부의 기포요동이 입자마모의 주요 원인으로 사료되었다. 탈황제의 마모속도가 작아서 회분식 측정결과가 연속식 유동층에 근사하게 적용될 수 있는 조건에서 수행되었다. 탈황공정에서 주요 변수인 기체유속, 온도, 압력, 층물질량의 변화에 따른 AI(attrition index)와 CAI(corrected attrition index)를 측정하였다. AI(5), CAI(5)는 층 무게가 증가함에 따라 감소하였다. 입자는 일정기간 충격에 의한 피로현상이 있은 후 마모되는 것으로 판단되었다. AI와 CAI는 기체속도, 상대습도, 압력이 증가함에 따라, 온도가 감소함에 따라 증가하였다. 입자마모는 주로 제트에 의하여 일어났으며 절단(fragmentation)보다 마쇄(abrasion)에 의하여 더 많은 미분입자가 발생하였다.