• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2010.05a
• /
• pp.711-712
• /
• 2010

• Transactions of Materials Processing
• /
• v.18 no.4
• /
• pp.336-341
• /
• 2009

Hydroformed parts have higher dimensional accuracy, structural strength, and dimensional repeatability. Particularly in the automotive industry, manufacturing of parts with complex shapes from tubular materials sometimes requires one or more pre-forming operations such as bending before the hydroforming process. The pre-bending process is an important process for the successful hydroforming in the case where the perimeter of the blank is nearly the same as that of final product. The bendability of a tube depends on the parameters such as the bending radius, welding methods, mechanical properties and hardness. Through the stainless steel tubes bent by rotary draw bending machine, this study shows the following : (1) The influence on spring back ratio variation with stress level in the welded bent tube. (2) The Cross-section ovality variation with weld seam position and bending radius. (3) The relation between elongation and thickness reduction of tension zone with weld seam position and bending radius. (4) Workability evaluation of bent stainless steel tubes through the hardness of materials and hardness increment. The results of this study may help to understanding of characteristics on bendability of stainless steel tubes.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2009.05a
• /
• pp.244-247
• /
• 2009

Hydroformed parts have higher dimensional accuracy, structural strength, and dimensional repeatability. Particularly in the automotive industry, manufacturing of parts with complex shapes from tubular materials sometimes requires one or more pre-forming operations such as bending before the hydroforming process. The pre-bending process is an important factor for successful hydroforming in the case where the perimeter of the blank is nearly the same as that of final product. The bendability of a tube depends on the parameters such as the bending radius, variation of the diameter, thickness, hardness. This study shows the analysis of bending through the stainless steel tubes bent to rotary draw bending machine.

• Molecules and Cells
• /
• v.45 no.1
• /
• pp.33-40
• /
• 2022

The various DNA-protein interactions associated with the expression of genetic information involve double-stranded DNA (dsDNA) bending. Due to the importance of the formation of the dsDNA bending structure, dsDNA bending properties have long been investigated in the biophysics field. Conventionally, DNA bendability is characterized by innate averaging data from bulk experiments. The advent of single-molecule methods, such as atomic force microscopy, optical and magnetic tweezers, tethered particle motion, and single-molecule fluorescence resonance energy transfer measurement, has provided valuable tools to investigate not only the static structures but also the dynamic properties of bent dsDNA. Here, we reviewed the single-molecule methods that have been used for investigating dsDNA bendability and new findings related to dsDNA bending. Single-molecule approaches are promising tools for revealing the unknown properties of dsDNA related to its bending, particularly in cells.

• Journal of the Korean Society for Heat Treatment
• /
• v.26 no.5
• /
• pp.225-232
• /
• 2013

The influence of aging treatment, addition elements and rolling reduction ratio on the microstructure, mechanical, electrical and bendability properties of Cu-Ni-Si-P-x (x = Fe, Sn, Zn) alloys for connector material application was investigated. SEM/EDS analysis exhibited that Ni2-Si precipitates with a size of 20~100 nm were distributed in grains. Fe, Sn, Zn elemnets in Cu-Ni-Si-P alloy imporved the mechanical strength but it was not favor in increasing of electrical conductivity. As higher final rolling reduction ratio, the strength and electrical conductivity is increased after aging treatment, but it indicated excellent bendability. Especially, Cu-2Ni-0.4Si-0.5Sn-0.1Fe-0.03P alloy show the tensile strength value of 700MPa and the electrical conductivity was observed to reach a maximum of 40%IACS. It is optimal for lead frame and connector.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.04a
• /
• pp.513-517
• /
• 1997

Glass fiber reinforced thermoplastic composite materials have considerable promise for increased use in low cost high volum applications because of the potential for processing by solid phase forming. However, the forming characteristics of these materials have not been well known. The primary focus of this research is the investigation of the bendability of these composites and spring-back phenomena in pure bending. The materials tested contained 10, 35, and 40 percent by weight of randomly oriented glass fiber in a polypropylene matrix. The bending tests were performed at temperatures ranging form 75 ".deg. c" to 150 ".deg. c" and at punch speeds of 2.54 mm/sec and 0.0254 mm/sec. The measured bendability and spring back angle in pure bending werw compared with the predictions based on the simple analyical models. Goog agreement between experimental and analytical results was observed.esults was observed.

• Journal of the Korean Society for Precision Engineering
• /
• v.15 no.3
• /
• pp.119-126
• /
• 1998

유리섬유 강화 열가소성 복합재료는 고상성형법에 의해 저렴한 가격으로 큰 부피의 제품의 제조에 널리 사용될 수 있어 아주 좋은 전망을 가지고 있다. 그러나 이러한 재료의 성형성이나 재료거동의 특성은 아직 잘 파악되지 않았다. 본 연구의 주안점은 이러한 재료의 단순 굽힘에서의 굽힘성형성을 연구하는데 두었다. 실험에 사용된 재료는 임의의 방향으로 위치한 유리섬유를 중량비로 20 %, 35 %, 40 % 함유한 폴리프로필렌이다 굽힘시험은 75 $^{\circ}C$에서 150 $^{\circ}C$ 사이의 온도에서 25 $^{\circ}C$ 씩 증가하면서 행했고, 편치속도는 2.54 mm/sec와 0.0254 mm/sec에서 행했다. 단순 굽힘시험에서 측정된 굽힘성형성은 해석적 모델로 예측한 결과와 비교하였다. 실험결과와 예측결과가 비교적 잘 일치함을 보였으며, 굽힘성 map으로써 성형 온도와 펀치반경의 좌굴에 대한 효과를 가시화 함은 물론 좋은 성형조건을 선정할 수 있는 좋은 도구로써 나타내었다.

• Transactions of Materials Processing
• /
• v.9 no.1
• /
• pp.27-34
• /
• 2000

Sheet metal formabilities for aluminum 1050 and 5052 were experimentally investigated in this study. Deep drawability, bendability and stretch formability were measured at each process condition and correlated with tensile properties of sheet metal. To compare the formabilities of aluminum 1050 and 5052 sheets with those of steel sheets, deep drawing quality(DDQ) steel sheets are also tested at the same test conditions. Through the experimental studies, influential process variables for each forming process were obtained and correlated with the tensile properties. The comparisons of sheet metal formabilities with those of steed sheets showed that aluminum 1050 and 5052 is inherently deficient in formability than steel sheets but Al 5052 that has highter n and r value than al 1050 showed better formabilities.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2010.05a
• /
• pp.709-710
• /
• 2010

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2012.05a
• /
• pp.65-66
• /
• 2012