• Journal of the Korean Chemical Society
• /
• v.61 no.1
• /
• pp.16-24
• /
• 2017

The adsorption of various atmospheric harmful gases ($CO_x$, $NO_x$, $SO_x$) on graphene-like boron nitride(BN) and aluminum nitride(AlN) sheets was theoretically investigated using density functional theory (DFT) and MP2 methods. The structures were fully optimized at the $B3LYP/6-31G^{**}$ and $CAM-B3LYP/6-31G^{**}$ levels of theory and confirmed to be a local minimum by the calculation of the harmonic vibrational frequencies. The MP2 single-point binding energies were computed at the $CAM-B3LYP/6-31G^{**}$ optimized geometries. Also the zero-point vibrational energy (ZPVE) and 50%-basis set superposition error (BSSE) corrections were included. The adsorptions of gases on the BN sheet were predicted to be a physisorption process and the adsorptions of gases on the AlN sheet were predicted to be a physisorption process for $CO_x$ and $NO_x$ but to be a chemisorption process for $SO_x$.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.13 no.2
• /
• pp.471-477
• /
• 2012

SCM420 steel tempered after performing gear hove PACVD carbide coating on the surface after the cutting surface hardness was high. Difficult-to-cut, without coating is classified as mild as large, including materials like mild, high strength that improves tool life and productivity have limited availability. Drive to improve it in the TiCN-coated carbide call for war to the finish coating on cutting a hob skiving good workability, tool wear less, 2.5-fold increase in tool life results were obtained. Experiments using CNC Skiving hobbing machine with wet cutting conditions, cutting speed and feed rate to apply a variety of the tool wear and surface roughness data were obtained. Results from condition 2 (V = 200m/min F = 0.7mm/rev) cutting speed feed mark the cutting surface microstructure and surface roughness Rmax $4.7{\mu}m$(Ra $1.19{\mu}m$) of the data was obtained.

• Progress in Superconductivity
• /
• v.14 no.2
• /
• pp.99-101
• /
• 2012

Fluorescent yield X-ray absorption fine structure (XAFS) spectroscopy is useful for analyzing local structure of specific elements in matrices. We developed an XAFS apparatus with a 100-pixel superconducting tunnel junction (STJ) detector array with a high sensitivity and a high resolution for light-element dopants in wide-gap semiconductors. An STJ detector has a pixel size of $100{\mu}m$ square, and an asymmetric layer structure of Nb(300 nm)-Al(70 nm)/AlOx/Al(70 nm)-Nb(50 nm). The 100-pixel STJ array has an effective area of $1mm^2$. The XAFS apparatus with the STJ array detector was installed in BL-11A of High Energy Accelerator Research Organization, Photon Factory (KEK PF). Fluorescent X-ray spectrum for boron nitride showed that the average energy resolution of the 100-pixels is 12 eV in full width half maximum for the N-K line, and The C-K and N-K lines are separated without peak tail overlap. We analyzed the N dopant atoms implanted into 4H-SiC substrates at a dose of 300 ppm in a 200 nm-thick surface layer. From a comparison between measured X-ray Absorption Near Edge Structure (XANES) spectra and ab initio FEFF calculations, it has been revealed that the N atoms substitute for the C site of the SiC lattice.

• Steel and Composite Structures
• /
• v.21 no.1
• /
• pp.1-36
• /
• 2016

In the present study, the nonlinear magneto-electro-mechanical free vibration behavior of rectangular double-bonded sandwich microbeams based on the modified strain gradient theory (MSGT) is investigated. It is noted that the top and bottom sandwich microbeams are considered with boron nitride nanotube reinforced composite face sheets (BNNTRC-SB) with electrical properties and carbon nanotube reinforced composite face sheets (CNTRC-SB) with magnetic fields, respectively, and also the homogenous core is used for both sandwich beams. The connections of every sandwich beam with its surrounding medium and also between them have been carried out by considering Pasternak foundations. To take size effect into account, the MSGT is introduced into the classical Timoshenko beam theory (CT) to develop a size-dependent beam model containing three additional material length scale parameters. For the CNTRC and BNNTRC face sheets of sandwich microbeams, uniform distribution (UD) and functionally graded (FG) distribution patterns of CNTs or BNNTs in four cases FG-X, FG-O, FG-A, and FG-V are employed. It is assumed that the material properties of face sheets for both sandwich beams are varied in the thickness direction and estimated through the extended rule of mixture. On the basis of the Hamilton's principle, the size-dependent nonlinear governing differential equations of motion and associated boundary conditions are derived and then discretized by using generalized differential quadrature method (GDQM). A detailed parametric study is presented to indicate the influences of electric and magnetic fields, slenderness ratio, thickness ratio of both sandwich microbeams, thickness ratio of every sandwich microbeam, dimensionless three material length scale parameters, Winkler spring modulus and various distribution types of face sheets on the first two natural frequencies of double-bonded sandwich microbeams. Furthermore, a comparison between the various beam models on the basis of the CT, modified couple stress theory (MCST), and MSGT is performed. It is illustrated that the thickness ratio of sandwich microbeams plays an important role in the vibrational behavior of the double-bonded sandwich microstructures. Meanwhile, it is concluded that by increasing H/lm, the values of first two natural frequencies tend to decrease for all amounts of the Winkler spring modulus.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.222.2-222.2
• /
• 2016

트랜지스터 응용 등에 관한 연구가 활발해 지면서 에너지 밴드갭이 0 eV에 가까운 그래핀 이외의 밴드 갭 조절이 가능한 MoS2 (molybdenum disulfide), BN (boron nitride), Bi2Te3 (bismuth telluride), WS2 (tungsten disulfide) 등과 같은 이차원 Transition Metal DiChalcogenides (TMDC) 물질이 반도체 물질로 각광받고 있다. 특히 MoS2의 경우 단결정 덩어리 상태에서는 약 1.3 eV의 밴드갭을 가지나 두께가 줄어들어 두 층일 경우에는 약 1.65 eV, 단일층이 되면 약 1.9 eV의 밴드갭을 가져 박막 층수에 따라 에너지 밴드갭 조절이 가능한 것으로 알려져있다. 하지만 두께 조절이 가능하면서 대면적, 고품질을 가지는 MoS2 박막 합성은 아직 제한적이라 할 수 있으며 새로운 방법 및 물질에 대한 연구가 지속적으로 이루어 지고 있다. 따라서 본 연구에서는 다양한 층수를 지니는 MoS2 합성을 위해 나노 두께의 MoS2 박막을 CF4 plasma 를 이용하여 layer etching 진행하고 CF4 plasma 100초 etching 진행한 2 layer 두께의 MoS2를 기준으로 H2S plasma를 이용하여 treatment 진행하였다. 물리적, 화학적 분석은 Raman spectroscopy, XPS(X-ray Photoelectron Spectroscopy), AFM (Atomic Force Microscopy) 등을 이용해 진행하였고 이를 통해 MoS2 layer 감소 및 damage recovery 등을 확인하였다.

• Korean Journal of Materials Research
• /
• v.20 no.4
• /
• pp.194-198
• /
• 2010

Cubic boron nitride (c-BN) is a promising material for use in many potential applications because of its outstanding physical properties such as high thermal stability, high abrasive wear resistance, and super hardness. Even though 316L austenitic stainless steel (STS) has poor wear resistance causing it to be toxic in the body due to wear and material chips, 316L STS has been used for implant biomaterials in orthopedics due to its good corrosion resistance and mechanical properties. Therefore, in the present study, c-BN films with a $B_4C$ layer were applied to a 316L STS specimen in order to improve its wear resistance. The deposition of the c-BN films was performed using an r.f. (13.56 MHz) magnetron sputtering system with a $B_4C$ target. The coating layers were characterized using XPS and SEM, and the mechanical properties were investigated using a nanoindenter. The friction coefficient of the c-BN coated 316L STS steel was obtained using a pin-on-disk according to the ASTM G163-99. The thickness of the obtained c-BN and $B_4C$ were about 220 nm and 630 nm, respectively. The high resolution XPS spectra analysis of B1s and N1s revealed that the c-BN film was mainly composed of $sp^3$ BN bonds. The hardness and elastic modulus of the c-BN measured by the nanoindenter were 46.8 GPa and 345.7 GPa, respectively. The friction coefficient of the c-BN coated 316L STS was decreased from 3.5 to 1.6. The wear property of the c-BN coated 316L STS was enhanced by a factor of two.

• ETRI Journal
• /
• v.14 no.1
• /
• pp.40-51
• /
• 1992

$0.25{\mu} m$ 급 pMOSFET소자를 구현하기 위해, $P^+$ 폴리실리콘을 적용한 pMOS를 제작하였으며, $p^+$ 폴리실리콘 게이트 소자에서 심각하게 문제가 되고 있는 붕소이온 침투현상을 조사하고 붕소이온 침투가 일어나지 않는 최적열처리온도를 조사하였다. 소자제조 공정중 게이트 공정만 전자선 (EBML300)을 이용하여 직접묘사하고 그 이외의 공정은 stepper(gline) 을 사용하는 Mix & Match 방법을 사용하였다. 또한 붕소이온 침투현상을 억제하기 위한 한가지 예로서, 실리콘산화막과 실리콘질화막을 적층한 ONO(Oxide/Nitride/Oxide) 구조를 게이트 유전체로 적용한 소자를 제작하여 그 가능성을 조사하였다. 그 결과 $850^{\circ}C$의 온도와 $N_2$ 분위기에서 30분동안 열처리 하였을 경우, 붕소이온의 침투현상이 일어나지 않음을 SIMS(Secondary Ion Mass Spectrometer) 분석 및 C-V(Capacitance-Voltage) 측정으로 확인할 수 있었으며 그 이상의 온도에서는 붕소이온이 침투되어 flat band전압(Vfb)을 변화시킴을 알았다. 6nm의 얇은 게이트 산화막 및 $0.1{\mu} m$ 이하의 LDD(Lightly Doped Drain) $p^-$의 얇은 접합을 형성함으로써 소자의 채널길이가 $0.2 {\mu} m$까지 짧은 채널효과가 거의 없는 소자제작이 가능하였으며, 전류구동능력은 $0.26\muA$/$\mu$m(L=0.2$\mu$m, V$_DS$=2.5V)이었고, subthreshold 기울기는 89-85mV/dec.를 얻었다. 붕소이온의 침투현상을 억제하기 위한 한가지 방법으로 ONO 유전체를 소자에 적용한 결과, $900^{\circ}C$에서 30분의 열처리조건에서도 붕소이온 침투현상이 일어나지 않음으로 미루어 , $SiO_2$ 게이트 유전체보다 ONO 게이트 유전체가 boron 침투에 대해서 좋은 장벽 역활을 함을 알았다. ONO 게이트 유전체를 적용한 소자의 경우, subthreshold특성은 84mV/dec로서 좋은 turn on,off 특성을 얻었으나, ONO 게이트 유전체는 막자체의 누설전류와 실리콘과 유전체 계면의 고정전하량인 Qss의 양이 공정조건에 따라 변화가 심해서 문턱전압 조절이 어려워 소자적용시 문제가 된다. 최근 바닥 산화막(bottom oxide) 두께가 최적화된 ONO 게이트 유전체에 대하 연구가 활발히 진행됨을 미루어, 바닥 산화막 최적화가 된다면 더 좋은 결과가 예상된다.

• Design & Manufacturing
• /
• v.10 no.3
• /
• pp.14-19
• /
• 2016

Thermally or electrically conductive filler reinforced polymer composites are extensively being developed as the demand for light weight material increases rapidly in industiral applications need good conductivity such as heat sink of the electronics or light. Carbon or ceramic materials like graphite, carbon nanotube or boron nitride are typical conductive fillers with good thermal or electical conductivity. Using these conductive fillers, the polymer composites in the market show wide range of thermal conductivity from approximately 1 W/mK to 20 W/mK, which is quite enhanced considering the thermal conductivity lower than 0.5 W/mK for most polymeric materials. The practical use of these composites, however, is yet limited to specific applications because most composites are still not conductive enough or too difficult to process, too brittle, too expensive for higher conductivity. For practical use of conductive composite, the thermal conductivity required depending on the heat releasing mode are studied first for simplified unit cooling geometry to propose thermal conductivities of the composites for reasonable cooling performance comparing with the metal heat sink as a reference. Also, as a practical design for heat sink based on polymer composite, composite and metal sheet hybrid structures are investigated for LED lamp heat sink and audio amplication module housing to find that this hybrid structure can be a good solution considering all of the cooling performance, manufacturing, mechanical performance, cost and weight.

• International Journal of Precision Engineering and Manufacturing
• /
• v.5 no.3
• /
• pp.35-42
• /
• 2004

This research describes that the cutting characteristics and tool wear behavior in the micro cutting of three kinds of wear resistant cemented carbides (WC-Co; V40, V50 and V60) using PCD (Poly Crystalline Diamond) and PCBN (Poly crystalline Cubic Boron Nitride) cutting tools by use of the SEM (Scanning Electron Microscope) direct observation method. The purpose of this research is to present reasonable cutting conditions from the viewpoint of high efficient cutting refer to a precise finished surface and tool wear. Summary of the results is as follows: (1) The cutting forces tend to increase as the increase of the weight percentage of WC particles, and the thrust forces was larger than the principal forces in the cutting of WC-Co. These phenomena were different from the ordinary cutting such as cutting of steel or cast iron. (2) The cutting speed hardly influenced the thrust force, because of the frictional force between the cutting tool edge and small WC particles at low cutting speed region such as 2$\mu\textrm{m}$/s. It seemed that the thrust cutting force occurred by the contact between the flank face and work material near the cutting edge. (3) The wear mechanism for PCD tools is abrasion by hard WC particles of the work materials, which leads diamond grain to be detached from the bond. (4) From the SEM direct observation in cutting the WC-Co, it seems that WC particles are broken and come into contact with the tool edge directly. This causes tool wear, resulting in severe tool damage. (5) In the orthogonal micro cutting of WC-Co, the tool wear in the flank face was formed bigger than that in the rake face on orthogonal micro cutting. And the machining surface integrity on the side of the cutting tool with a negative rake angle was better than that with a positive one, as well as burr in the case of using the cutting tool with a negative rake angle was formed very little compared to the that with a positive one.

• Structural Engineering and Mechanics
• /
• v.64 no.3
• /
• pp.361-379
• /
• 2017

In this article, the vibration behavior of double-bonded sandwich microplates with homogeneous core and nanocomposite facesheets reinforced by carbon nanotube and boron nitride nanotube under multi physical fields such as 2D magnetic and electric fields is investigated. Symmetric and un-symmetric distributions of nanotubes are considered for facesheets of sandwich microplates such as uniform distribution and various functionally graded distributions. The double-bonded sandwich microplates rest on visco-Pasternak foundation. Material properties of sandwich microplates are obtained by the extended rule of mixture. The sinusoidal shear deformation theory (SSDT) is employed to describe displacement fields of sandwich microplates. Also, the dimensionless natural frequency is obtained by classical plate theory (CPT) and compared with the obtained results by SSDT. It can be seen that the obtained dimensionless natural frequencies by CPT are higher than SSDT. In order to study the material length scale parameters, modified strain gradient theory at micro scale is utilized and then, the equations of motion are derived using Hamilton's principle. The effects of different parameters such as foundation parameters including Winkler, shear layer and damping coefficients, various distributions and volume fraction of nanotubes, core to facesheet thickness ratio, aspect and side ratios on the dimensionless natural frequencies are discussed in details. The results of present work can be used to optimum design and control of similar systems such as micro-electro-mechanical and nano-electro-mechanical devices.