• 한국대기환경학회지
• /
• 제16권2호
• /
• pp.199-208
• /
• 2000

In this study we investigated on the possibility of platinum and silver catalysts as de-NOx catalyst for activity test of supported metal oxide catalysts. the study was performed with the change of amount of metal and support types. The catalyst was prepared the activity of alumina supported silver catalyst produced by dry and wet impregnation method respectively and the resistance of sulfur for optimum supported silver catalyst,. As a result the activity of alumina supported platinum catalyst was showed at low temperature region but the case of silver catalyst activated at high temperature region. So we finally chose alumina supported silver catalyst as de-NOx target catalyst because alumina supported catalyst showed higher activity than alumina supported platinum catalyst.

• 한국수소및신에너지학회논문집
• /
• 제31권2호
• /
• pp.202-209
• /
• 2020

In methanol steam reforming, commercial catalysts in the form of pellets are mainly used, but there are limitations to directly apply them to underwater weapon systems that require shock resistance and heat transfer characteristics. In this study, to overcome this problem, a multi-layer cup structure (MLCS) was applied to support a pellet type catalyst. The characteristics of pellet catalyst supported by MLCS and the pellet catalyst supported by conventional structure (CS) were compared by the reforming experiment. In the case of MLCS, a high methanol conversion rate was shown in the temperature range 200 to 300℃ relative to the CS manufactured with the same catalyst weight as MLCS. CS shown similar characteristics to MLCS when it manufactured in the same volume as MLCS by adding an additional 67% of the catalyst. In conclusions, MLCS can not only reduce catalyst usage by improving heat transfer characteristics, but also support pellet catalyst in multiple layers, thus improving shock resistance characteristics.

• Korean Chemical Engineering Research
• /
• 제61권3호
• /
• pp.341-347
• /
• 2023

PEMFC(Proton Exchange Membrane Fuel Cells)에서 PtCo/C 합금 촉매가 성능이나 내구성에서 우수하여 많이 사용되고 있다. 그러나 높은 전압에서(1.0~1.5 V) 평가되는 촉매 지지체 내구성에 관한 연구는 별로 보고 되지 않았다. 본 연구에서는 PtCo/C 촉매와 Pt/C 촉매에 촉매 지지체 가속 열화 프로토콜을 적용한 후 내구성을 비교하였다. 1.0↔1.5V 전압 변화 사이클 반복 후에 촉매 비활성도(Mass activity)와 전기화학적 활성면적(ECSA), 전기이중층 용량(DLC), Pt 용해와 입자 성장 등을 분석하였다. 전압변화 2,000 사이클 후 PtCo/C 촉매는 Pt/C 촉매에 비해 0.9 V에서 촉매 무게당 전류밀도가 1.5배 이상 감소하였다. 이와 같은 결과는 PtCo/C 촉매의 카본지지체의 열화 속도가 Pt/C 촉매보다 높기 때문이었다. Pt/C 촉매는 PtCo/C 촉매보다 촉매층의 ECSA 감소가 1.5배 이상 높았지만 Pt/C 촉매의 카본 지지체 부식이 작아 I-V 성능 감소가 작았다. PtCo/C 촉매의 고전압 내구성 향상을 위해서는 카본 지지체 내구성 향상이 필수적임을 보였다.

• Carbon letters
• /
• 제8권1호
• /
• pp.37-42
• /
• 2007

Carbon nanofiber (CNF) grown catalytically was chemically activated with KOH to attain structural change of CNF. The structural changes of CNF through KOH activation were investigated by using BET and SEM. From the results of BET, it was found that KOH activation was effective to develop particular sizes of pores on the CNF surface, increasing the surface area of CNF. Activated CNF was applied as an anode catalyst support of fuel cell. The effects of different activation conditions including the activation temperature and the activation time on the specific surface area of the CNF activated with KOH were investigated to obtain appropriate structure as a catalyst support. The 60 wt% Pt-Ru catalyst prepared was observed by using TEM and XRD.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2010년도 춘계학술대회 초록집
• /
• pp.135.2-135.2
• /
• 2010

Carbon nanotube(CNT) has been spotlighted as a promising candidate for catalyst support material for PEMFC (proton exchange membrane fuel cell). The considerable properties of CNT include high surface area, outstanding thermal, electrical conductivity and mechanical stability. In this study, to fully utilize the properties of CNTs, we prepared directly oriented CNT on carbon paper as a catalyst support in the cathode electrode. The CNT layer was prepared by a chemical vapor deposition(CVD) process. And the Pt particles were deposited on the CNT oriented carbon paper by impregnation and eletro-deposition method. The potential advantages of directly oriented CNT on carbon paper can include improved thermal and charge transfer through direct contact between the electrolyte and the electrode and enhanced exposure of Pt catalyst sites during the reaction.

• 한국세라믹학회지
• /
• 제36권5호
• /
• pp.504-512
• /
• 1999

The high-quality carbon nanofibers were prepared by chemical vapor deposition of gas mixtures of CO-H2 and C3H8-H2 over Fe-Cu and Ni-Cu bimetallic catalysts. The yield and structure of carbon nanofiber produced were altered by the change of catalyst composition and reaction temperature. The high yields were obtained around 500$^{\circ}C$ with e-Cu catalyst and around 700-750$^{\circ}C$ with Ni-Cu catalyst and the relatively higher yields were obtained with the bimetallic catalyst containing 50-90% of Ni and Fe respectively in comparison with the pure metals. The carbon nanofibers produced over the Fe-Cu catalyst at around 500$^{\circ}C$ with the maximum yields had the highest surface ares of 160-200 m2/g around 650$^{\circ}C$ which was slightly lower than the temperature for maximum yields. In order to examine the characteristics of carbon nanofibers as catalyst support Ni and Co metals were supporte on the carbon nanofibers and CO hydrogenation reaction was performed with the catalysts. The particle size distribution of Ni and Co supported over the carbon nanofibers were 6-15 nm and the CO hydrogenation reaction rate with the carbon-nanofiber supported catalysts was much higher than that over the other supports.

• 한국전기전자재료학회논문지
• /
• 제36권2호
• /
• pp.164-169
• /
• 2023

Nano Pt particles were dispersed on carbon-based supports by a polyol process for a catalyst application in a polymer electrolyte fuel cell. We tried to optimize the effect of pH on the electrostatic forces between the support and the Pt colloids. We investigated the relationship among the surface charges on the carbon support, the solution pH, and the concentration of a glycolate, and the Pt particle size. The produced catalyst with nano Pt particles on the support was evaluated by the long-term cyclic voltammetry (CV) performance test and compared with the results from a commercial catalyst. Our experimental results reveal that the pH-control can modify the particle size distribution and the dispersion of the nano Pt particles. This resulted in a cost-effective method for the synthesis of highly Pt loaded Pt/C catalysts for fuel cells better than a commercial catalyst system.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2006년도 춘계학술대회
• /
• pp.110-112
• /
• 2006

Membrane electrode assembly (MEA) for polymer electrolyte fuel cell (PEFC) are commonly prepared in the research laboratory by spraying, screen-printing and brushing catalyst slurry onto membrane or other support material like carbon paper or polyimide film in a batch style. These hand applications of the catalyst slurry are painstaking process with respect to precision of catalyst loading and reproducibility. It has been generally mentioned that the adoption of continuous process is very helpful to develop the reliable product. In the present work, we report the results of using continuous type coater with doctor-blade to coat catalyst slurry for preparing the MEA catalyst layers In a faster and highly reproducible fashion. We show that while expectedly faster than batch style, the machine coater requires the use of slurry of appropriate composition and a properly selected transfer decal material in order to achieve superior MEA plat lnw loading reproducibility. To make highly viscous catalyst slurry that is imperative for using coater, we use 40wt.% Nafion solution and minimize the content of organic solvent. And the choice of proper high surface area catalyst is important in the viewpoint of making well-dispersed slurry. After catalyst coating onto the support material, we transferred the catalyst layer to both sides of Nafion membrane by hot-pressing In this case, the degree of transfer was Influenced by hot-pressing condition including temperature, pressure, and time. To compare the transferring ability, we compared so many films and detaching papers. And among the support, polyethylene terephthalate(PET) film shows the prominent result.

• 한국전기화학회:학술대회논문집
• /
• 한국전기화학회 2003년도 연료전지심포지움 2003논문집
• /
• pp.193-197
• /
• 2003

Mixture of $Ni(OH)_2-Mg(OH)_2$ used as the precurs was treated by mechnochemical(MC) and hand grinding process. Carbon nanofibers(CNF) were prepared using CVD process with the above prepared catalyst. CNFs with a uniform diameter were obtained with MC process treated catalyst, and the diameter could be controlled by tuning the grinding time. CNF bundles with close coalescence were produced with MC treated catalyst. After purification of CNFs and loading with Pt, they were used in fuel cell as the cathode catalyst support. The performance with carbon nanofibers prepared using ground mixture was found to be better than that prepared using unground mixture, which is attributed to the homogeneous CNFs with small diameter and specific interaction between Pt and CNFs.

• Korean Chemical Engineering Research
• /
• 제53권2호
• /
• pp.262-268
• /
• 2015

본 연구에서는 일반적인 귀금속 담지법과 담체 위에 형성한 고분자 전해질 다층 박막 내에 귀금속을 내포시키는 방법으로 촉매를 제조하고, 과산화수소 직접제조 반응에 적용하여 촉매의 제조 방법이 과산화수소 생산성 및 촉매 수명에 미치는 영향을 조사하였다. 촉매의 활성은 제조 방법에 상관없이 담체의 산세기에 크게 의존하였으며, 사용한 담체들 중 산세기가 가장 강한 HBEA(SAR=25)를 사용한 경우가 활성이 가장 우수하였다. 단순 귀금속 담지 촉매는 고분자 전해질 다층 박막을 도입한 촉매보다 과산화수소 생산성은 우수하였으나, 반응 중 활성 금속인 Pd의 용출로 인해 재사용 횟수가 증가할 때마다 활성이 급격히 감소하였다. 한편, 고분자 전해질 다층 박막의 도입은 산성 담체의 역할을 약화시켜 촉매 활성은 감소하고 과산화수소 분해능은 증가하여 전체적으로 과산화수소의 생산성이 감소되는 결과를 가져왔다. 하지만, 5회에 걸친 재사용 동안에도 촉매 활성이 유지되었으며, 이러한 비약적인 촉매 수명의 향상은 담체 위에 고분자 전해질 다층 박막을 도입하는 것이 반응 중 활성 금속의 용출 억제 측면에서 매우 효과적이라는 것을 시사한다.