• 한국공작기계학회논문집
• /
• 제10권3호
• /
• pp.75-82
• /
• 2001

The continuous chip in turning operation deteriorates the precision of workpiece and can cause a hazardous condition to operator. Thus the chip form becomes a very important task for reliable turning process. The chip form is identified using the neural network of supervise data Through the measurement of energy radiated from the chip. The feed mechanism os adjusted in order to break continuous chip according to the result of the chip form recognition and it shows a good approach for precision turning operation.

• 한국정밀공학회지
• /
• 제13권7호
• /
• pp.59-65
• /
• 1996

A major problem in automation of turning operations is the difficulty in obtaining a sufficient and reliable chip control. Therefore it becomes desirable to find a method which can detect the chip form. Newly born chips in usual metal cutting radiate infrared rays. When such chips run out of cutting point quickly, the radiated energy from the zone around the tool is low compared with that of the case when long tangled chips are staying around the tool. The difference in chip pattern can be detected from the output of pyrometer. But, strictly speaking, only the output of pyrometer does not identify the chip form because that is the removal of chip. Therefore, in this paper, a method of the identification of chip form using output of pyrometer and fuzzy inference is developed.

• 동력기계공학회지
• /
• 제4권4호
• /
• pp.108-115
• /
• 2000

The continuous chip in turning operation deteriorates the precision of workpiece and can cause a hazardous condition to operator. Thus the chip form control becomes a very important task for reliable turning process. Using the difference of energy radiated from the chip, the chip form is identified using the neural network of supervised data. The feed mechanism is adjusted in order to break continuous chip according to the result of the chip form recognition and shows a good approach for precision turning operation.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1996년도 추계학술대회 논문집
• /
• pp.206-211
• /
• 1996

A major problem in automation of turning operation is the difficulty in obtaining a sufficient and reliable chip control. Therefore it becomes desirable to find a method which can detect the chip form. In this paper, a method of the identification of chip form using output of pyrometer and neural network technique is developed. An efficiency of developed method is examined by experiments in turning and the validity of it is confirmed.

• 한국생산제조학회지
• /
• 제8권4호
• /
• pp.61-67
• /
• 1999

In turning the chip may be produced in the form of continuous chip or discontinuous one. Continuous chips produced at high speed machining may hit the newly cut workpiece surface and adversely affect the appearance of the surface finish and may interfere with tool and sometimes induce tool fracture. In this study relationship between AE signal and chip form was experimentally investigated, The experimental results show that types of chip form are possible to be classified from the AE signal using fuzzy logic.

• 한국산업융합학회 논문집
• /
• 제4권2호
• /
• pp.127-132
• /
• 2001

In turning, the chip may be produced in the form of continuous chip or discontinuous chip. The continuous chips are dangerous to the operator and difficult to be handled at high speed machining. The signal of AE(Acoustic Emission) is found out to be related to cutting conditions, tool materials, test conditions and tool geometry in turning. In this study, the relationship between AE signal and chip form was experimentally investigated. The experimental results show that the types of chip form are possible to be classified from the AE signal using fuzzy logic.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1993년도 춘계학술대회 논문집
• /
• pp.300-304
• /
• 1993

Chip formation control is an important problem in the automation of manufacturing process, since the continuous chip can cause catastrophic failures of the tooling and entangle the workpiece causing damage. However, it is impossible to predict chip form correctly due to the complex nature of cutting process. In order to detect the chip form for unmanned manufacturing, a new identification method is proposed. The feasibility of using acoustic emission signals from the sensing plate for identification of chip form is investigated. Experiments were conducted under the various cutting conditions. When the acoustic emission sensor is attached to the sensing plate, it turns out that the moving averaged AE signals correlated well with the collision of segmented chips with the plate. The sensitivity of moving averaged AE signals to chip congestions due to continuous chip formation is illustrated as well.

• 한국정밀공학회지
• /
• 제15권12호
• /
• pp.106-112
• /
• 1998

A major problem in automation of turning operations is the difficulty in obtaining a sufficient and reliable chip control. The chip should be detected in order to provide a optimum chip control for unmanned turning operation. Using the difference of energy radiated from the chip, chip Patterns are estimated using pyrometer. From the initial output from the pyrometer, chips are identified according to the backpropagation algorithm developed in the research. The learning system developed in this work can be applied in real-time control of turning process with minor modification in drive system.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 춘계학술대회 논문집
• /
• pp.993-997
• /
• 1997

The continuous chip depresses the accuracy of workpieces and promotes the wear of machine tools and hunts operators. So chip control os a major problem in turning process. In this paper, a method of chip identification is develope by pyrometer. The identifier is applied in real-time control of chip pattern with adjusting feedrate.

• 한국정밀공학회지
• /
• 제6권4호
• /
• pp.61-70
• /
• 1989

A new analytical method is proposed to monitor the chip form of cutting forces applying the techinque of signal process. Cutting experiments are carried out under various cutting conditons and cutting forces are measured in-processing through Tool Dynamometer. In this report, auto-correlation functions, frequency characteristics of dynamic force, high frequency distribution and Peak/RMS values are calculated from the measured cutting forces, and the concept of method is also discussed. The experimental results show that six types of the form of chips are possible to classify from the signal of cutting forces not related to cutting conditions.