• Elastomers and Composites
• /
• 제26권2호
• /
• pp.109-114
• /
• 1991

The graft copolymerization of chloroprene rubber with methyl methacrylate in toluene solution has been carried out varying the concentration of monomer, initiator, CR, reaction time, and reaction temperature, etc.. It is observed that the grafting reaction follows conventional kinetic behavior under the present experimental conditions. Identification of grafting on to chloroprene rubber was obtained through characterization of the graft copolymer by infrared spectrometer.

• 한국전기전자재료학회논문지
• /
• 제17권11호
• /
• pp.1205-1211
• /
• 2004

This study has investigated radiation degradation of chloroprene rubber in the presence of some fire retardant. Ammonium polyphosphate, aluminium trihydroxide, magnesium hydroxide, calcium carbonate and antimony trioxide were selected as flame retardant. Samples were irradiated using a Co$^{60}$ ${\gamma}$ -ray and ray up to 2000 kGy at a dose rate of 5 kGy/hr in the presence of air atmosphere at room temperature. After irradiation, samples were assessed fire retardancy with electrical properties and mechanical properties. Some considerations concerning the effects of the fire retardants added to chloroprene rubber on the radiation and thermal stability of chloroprene rubber are presented. From fire retardancy with electrical and mechanical property measurements, it was found that addition of magnesium hydroxide resulted in maximum fire retardant effect.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2003년도 가을 학술발표회 논문집
• /
• pp.553-556
• /
• 2003

This study is analyzed about the factor of adhesive strength characteristics, curing time, asphalt application, test temperature which are liquid waterproofing membrane of rubber-asphalt and chloroprene-rubber type for concrete bridge deck. According to the results, curing time is shorter, adhesive strength is less in chloroprene-rubber type. And also chloroprene-rubber and rubber-asphalt type are showed high adhesive strength in low temperature.

• Bulletin of the Korean Chemical Society
• /
• 제29권11호
• /
• pp.2264-2266
• /
• 2008

• Elastomers and Composites
• /
• 제54권1호
• /
• pp.40-53
• /
• 2019

The physical properties of chloroprene rubber (CR) compounds reinforced with networked silicas were investigated by comparing them to those reinforced with conventional silica to observe the effect of the organic connection bonds combining silica particles on their cure, tensile, and aging performance. The introduction of networked silica to CR increase in silica content to 80 phr in rubber, while the content of conventional silica was limited to 60 phr. The CR compounds reinforced with networked silica showed higher resistance to combustion. The gradual increases in delta torque, Mooney viscosity, and modulus of silica-filled CR compounds with silica content were mainly attributed to the specific interaction between the chlorine atoms of CR and the hydroxyl groups of silica. The CR compounds reinforced with networked silica showed low compression set and heat build-up and maintained their high modulus even after thermal, oil, and ozone aging.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2000년도 가을 학술발표회논문집(I)
• /
• pp.473-478
• /
• 2000

This report describes practices currently used for properties, applications and guide-lines of Chloroprene Rubber Liquid Membrane System for concrete bridge deck and relates these practices to in-service failures.

• Elastomers and Composites
• /
• 제31권4호
• /
• pp.256-271
• /
• 1996

• 한국구조물진단유지관리공학회 논문집
• /
• 제25권6호
• /
• pp.103-110
• /
• 2021

유연한 고무재료와 강재 보강판을 적층으로 구성한 탄성받침은 우수한 수직강성과 유연한 횡강성으로 교량의 내진보강용으로 널리 사용되고 있다. 무엇보다 시공이 간단하고 비용이 높지 않다는 장점을 지니고 있다. 고무재료의 한 종류인 합성고무는 천연고무에 비해 노화에 대한 저항성이 크지만 이 역시 다양한 열화요인으로 성능이 저하된다. 내진설계기준 및 내진성능평가요령에서는 이러한 노화의 특성을 반영하고 있지 않지만 관련 연구가 축적되면 이를 반영하는 것이 합리적이다. 합성고무를 대상으로 노화촉진시간과 노출시간을 변수로 하여 노화촉진시험을 수행하여 전단특성의 변화를 분석하였다. 노화가 진행될수록 최대전단응력과 전단변형율은 감소한다. 또한 동일한 전단변형률에서 전단강성이 크게 증가한다.

• Elastomers and Composites
• /
• 제8권2호
• /
• pp.140-147
• /
• 1973

The influence of the adhesive force test conditions on the resultant adhesive force was measured using a chloroprene rubber as an adhesive and a plywood as an adherent. It was clarified from the experiments which adhesive force test conditions could influence strongly the adhesive force. After this, the constant values neccessary as the test conditions of the adhesive force in making generally a test of the adhesive force determined.

• Elastomers and Composites
• /
• 제32권5호
• /
• pp.295-301
• /
• 1997

The effects of filler types and compositions on the final properties such as tensile strength, % elongation, hardness, and specific gravity of chloroprene rubber were investigated. The fillers involved in this investigation were HAF-type carbon black, Mistron, and white clay, For each filler, the variation of filler compositions gave almost the linear effects on the all properties investigated. For a fixed filler composition, different filler types gave different influential strength on rubber properties. After linearlization of experimental data with respect to each filler composition, the simple linear addition of each property with respect to filler compositions was applied to predict the final properties of the filler included rubber systems. For the chloroprene rubber system including the fillers composed of Mistron(25phr)/HAF(20phr)/clay(35phr), the predicted properties were well in accordance with the experimental results. Similar results were obtained for other additives such as processing oil and accelerator.