• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.08a
• /
• pp.150-150
• /
• 2011

Electron-neutral collision frequency is one of the important parameters in the plasma physics. Recently, It is employed to monitor the plasma processing in industrial plasma engineering [1]. Using the wave-cutoff probe with network analyzer, the plasma impedance was measured in inductively coupled argon plasma and analyzed to determine the resonance frequency. The electron-neutral collision frequency is directly calculated from the resonance frequency. The calculated electron-neutral collision frequency is good agree with reference which is calculated by measured EEDF using single langmuir probe (SLP).

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.234-234
• /
• 2011

Electron-neutral collision frequency is one of the important parameters in the plasma physics and in industrial plasma engineering. We can understand the momentum, energy, and charge transport properties of the plasma using electron-neutral collision frequency.[1] The wave-cutoff method is a diagnostic method for the electron density measurement, but the cutoff peak value depends on gas pressure. The wave-cutoff signal becomes unclear as increasing gas pressure. The reason of pressure dependence is that the electron-neutral collision disturbs electron motion so that microwave can propagate through plasma at plasma frequency.[2] Using the pressure dependence of wave-cutoff method we can find the electron-neutral collision frequency. At first we tried to confirm this method using well known gas such as Ar. The cutoff signal decrease as increasing gas pressure (the simulation result). The wave-cutoff signal is unclear at a gas pressure of 500 mTorr. (electron density $1.0{\times}10^{10}/cm^3$, electron temperature 1.7 eV, electron -neutral collision frequency~1 GHz). In this condition, the electron-neutral collision frequency is closed to the wave-cutoff frequency.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2004.11a
• /
• pp.663-666
• /
• 2004

An analysis of the annual frequency of collapse(AF) is performed for each bridge pier exposed to ship collision. AF is computed for each bridge component and vessel classification. The summation of AFs computed over all of the vessel classification intervals for a specific component should equal the annual frequency of collapse of the component. The designer should use judgment in developing a distribution of the vessel frequency data based on discrete groupings or categories of vessel size by DWT. In the present study the effect of vessel classification on the annual frequency of collapse in the ship collision risk assessment is investigated by illustrative numerical examples based on the vessel frequency data of the domestic harbor. The DWT interval for larger vessels has more effect on the ship collision risk. Therefore the expert judgement in determining the larger DWT interval is required because the design impact lateral resistances of bridge components depend on the ship collision risk.

• Journal of the Institute of Electronics Engineers of Korea CI
• /
• v.45 no.5
• /
• pp.85-94
• /
• 2008

When an RFID reader uses the same frequency or adjacent frequency with neighbor readers, the interference might occur. These interferences cause the RFID reader collision and errors during tag recognition. Therefore, the international standard for RFID and some papers proposed the methods to reduce the reader collision. The reader interference is closely related to the distance between the readers haying interference and used frequency band. In the previous RFID reader anti-collision algorithms, the location of readers inducing interference which is closely related to interference of readers is not considered. Only the reader collision is tried to reduce through frequency transfer after collisions occur or modification of frame size in relation to collision probability based a TDM(Time Division Multiplex). In this paper, the genetic algorithm using two-dimensional chromosome which reflect readers' location is proposed to prevent reader collision effectively. By executing evolutionary operation with two-dimensional chromosome, the location information having influence on reader interference can be used. The repair operation in the proposed algorithm makes all reader stably recognize their tags.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.39 no.11
• /
• pp.1033-1041
• /
• 2011

In this paper, a collision avoidance maneuver frequency for the KOMPSAT-2 and the KOMPSAT-5 is analyzed. For the statistical prediction of the avoidance maneuver frequency, mission orbits, responsive time, accepted collision probabilities, and positional uncertainties of primary and secondary objects are considered. In addition, the collision avoidance maneuver frequency of the KOMPSAT-2 is compared to the case that NORAD catalog during one year is used to calculate that of the KOMPSAT-2. As a result, the collision avoidance maneuver frequency is one per year on average and effective factors on the statistical prediction of the avoidance maneuver frequency are investigated. Efforts to improve its prediction accuracy are also discussed.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.16 no.9
• /
• pp.1939-1946
• /
• 2012

USNs (Ubiquitous Sensor Networks) such as IEEE 802.15.4 ZigBee network share ISM (Industrial, Scientific, and Medical) frequency band with WiFi networks. Once both networks operate in a region, packet collision may happen because of frequency overlapping. To assure this possibility, we conducted experiments where WiFi and ZigBee communication networks had been installed in an area. As a result of the test, successful data transmission rate were reduced due to the frequency overlapping between a WiFi communication channel and a ZigBee communication band. To cope with this problem, we propose a collision avoidance algorithm. In the proposed algorithm, if frequency collision is sensed, new communication channel with different frequency band is allocated to each node. Performance of the proposed frequency collision avoidance algorithm was tested and the results were described.

• Journal of the Korean Society for Railway
• /
• v.4 no.4
• /
• pp.155-161
• /
• 2001

In this paper, the method is suggested to prevent data collision or damage on RFID(Radio Frequency Identification) system, in case a reader reading multi-tag simultaneously, using binary-search algorithm and Time-domain anti-collision procedure at reader and tag, respectively. The RFID system is designed that Reader enable to communicate with Tag on 13.56MHz bandwidth which is ISM(Industrial Science Medical) bandwidth, antennas of Tag part are designed using MCRF335 Chip. When RF communication is achieved between reader and tag, in case that data is transmitted to reader pass through multiple tags simultaneously, a study on the anti-collision method for the situation that the data collision occurs is performed.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.32 no.4A
• /
• pp.358-364
• /
• 2007

RFID, Radio Frequency Identification, technology is a contactless automatic identification technology using radio frequency. For this RFID technology to be widely spread, the problem of multiple tag identification, which a reader identifies a multiple number of tags in a very short time, has to be solved. Up to the present, many anti-collision algorithms have been developed in order to solve this problem, and those can be largely divided into ALOHA based algorithm and tree based algorithm. In this paper, two new anti-collision algorithms combining the characteristics of these two categories are presented. And the performances of the two algorithms are compared and evaluated in comparison with those of typical anti-collision algorithms: 18000-6 Type A, Type B, Type C, and query tree algorithm.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.9 no.3
• /
• pp.941-955
• /
• 2015

In dual-channel networks (DCNs), all frequency hopping (FH) sequences used for data channels are chosen from the original FH sequence used for the control channel by shifting different initial phases. As the number of data channels increases, the hitting frequency point problem becomes considerably serious because DCNs is non-orthogonal synchronization network and FH sequences are non-orthogonal. The increasing severity of the hitting frequency point problem consequently reduces the resource utilization efficiency. To solve this problem, we propose a novel hitting frequency point collision avoidance method, which consists of a sequence-selection strategy called sliding correlation (SC) and a collision avoidance strategy called keeping silent on hitting frequency point (KSHF). SC is used to find the optimal phase-shifted FH sequence with the minimum number of hitting frequency points for a new data channel. The hitting frequency points and their locations in this optimal sequence are also derived for KSHF according to SC strategy. In KSHF, the transceivers transmit or receive symbol information not on the hitting frequency point, but on the next frequency point during the next FH period. Analytical and simulation results demonstrate that unlike the traditional method, the proposed method can effectively reduce the number of hitting frequency points and improve the efficiency of the code resource utilization.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.10 no.3
• /
• pp.123-134
• /
• 2006

In this study ship collision risk analysis is performed to determine the design vessel for collision impact analysis of the maritime bridge. Method II which is a probability based analysis procedure is used to select the design vessel for collision impact from the risk analysis results. The analysis procedure, an iterative process in which a computed annual frequency of collapse(AF) is compared to the acceptance criterion, includes allocation method of acceptance criterion of annual frequency of bridge component collapse. The AF allocation by weights seems to be more reasonable than the pylon concentration allocation method because this AF allocation takes the design parameter characteristics quantitatively into consideration although the pylon concentration allocation method brings more economical results when the overestimated design collision strength of piers compared to the strength of pylon is moderately modified. From the assessment of ship collision risk for each bridge pier exposed to ship collision, a representative design vessel for all bridge components is selected. The design vessel size varies much from each other in the same bridge structure depending upon the vessel traffic characteristics.