• 펄프종이기술
• /
• 제37권3호
• /
• pp.33-40
• /
• 2005

In this study, a nano-colloidal silica sol was applied to control the anti-slip property by spraying on kraft paper. Two kinds of nano-colloidal silica sol which have cationic and anionic charge were applied in kraft paper, and the friction and physical strength properties of kraft paper were investigated. The application of colloidal silica sol on wet web in wet-end process by spraying method was tried to improve the friction property and to avoid the general problems of machine contaminations caused by the scattering of sprayed silica particles in dryer part. The physical properties of sheet were also improved by the application of wet web spraying method, and the optimum conditions of wet web spraying operation were closely related with the conditions of pH and electrical charge of wet web and silica sol.

• 한국신뢰성학회지:신뢰성응용연구
• /
• 제14권1호
• /
• pp.11-19
• /
• 2014

A colloidal silica slurry has been manufactured by mixing nano silica powders having different grain size to improve the reliability of Sapphire wafer CMP process. The main reliability problem of CMP process such as the breaking of wafer can be prevented by reducing the size of particles in a slurry. While existing commercial colloidal silica slurries are usually made of single grain size silica powder of about 120nm, in the present study 40nm and 100nm silica powders are mixed to achieve a similar removal rate. The new colloidal silica slurry showed wafer removal rate of $3.04{\mu}m/120min$ while that of a commercial colloidal silica slurry was $3.03{\mu}m/120min$. The roughness was less than $4{\AA}$ and scratch was 0. It is also expected that the reduction of the size of nano silica particles can improve the dispersion stability and prolong the useful life of the slurry.

• Advances in concrete construction
• /
• 제3권3호
• /
• pp.187-202
• /
• 2015

The present study addresses about the development of sustainable concrete utilizing recycled coarse aggregates manufactured form waste concrete and colloidal Nano-Silica. Experimental investigations are carried out to determine compressive and tensile strength of concrete mixes designed with recycled coarse aggregates and different percentages of Nano-Silica. Moreover, water absorption, density and volume voids of concrete mixes are also examined to ascertain the influence of Nano-Silica on behavior of recycled aggregate concrete. The outcomes of the research depict that properties of concrete mixes are significantly affected with the introduction of recycled coarse aggregates in place of the natural coarse aggregates. However, the study reveals that the depletion of behavior of recycled aggregate concrete could be restored with the incorporation of little amount (3%) of Nano-Silica.

• 한국재료학회지
• /
• 제13권3호
• /
• pp.144-149
• /
• 2003

This study shows an experimental investigation of a reversible nano colloidal damper, which is statically loaded. The porous matrix is composed from silica gel (labyrinth or central-cavity architecture), coated by organo-silicones substances, in order to achieve a hydrophobic surface. Water is considered as associated lyophobic liquid. Reversible colloidal damper static test rig and the measuring technique of the static hysteresis are described. Influence of the pore and particle diameters, particle architecture and length of the grafted molecule upon the reversible colloidal damper hysteresis is investigated, for distinctive types and mixtures of porous matrices. Variation of the reversible colloidal damper dissipated energy and efficiency with temperature, pressure, is illustrated. As a result, he proposed nano damper is effective one, which can be replaced the conventional damper.

• 공업화학
• /
• 제19권1호
• /
• pp.45-50
• /
• 2008

본 연구에서는 나노 콜로이드 실리카에 은을 코팅하기 위하여 직접 은을 코팅하는 방법과 실리카입자 표면개질 후 은을 코팅하는 방법 등의 2가지 방법이 시도되었다. 실리카에 대한 은의 질량비율과 환원제 주입량 등이 은의 코팅에 미치는 영향을 조사하였다. 콜로이드 실리카에 직접 은을 코팅한 경우보다 MPTS (3-Mercaptopropyl trimethoxysilane)와 APTS (3-Aminopropyl trimethoxysilane)로 표면개질한 후 은을 코팅한 경우가 높은 은(Ag) 코팅율과 우수한 항균효과를 나타내는 것이 관찰되었다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2006년도 하계학술대회 논문집 Vol.7
• /
• pp.232-233
• /
• 2006

In recent years the interest in organic/inorganic hybrid materials has increased at a fast rate. Nano organic-inorganic hybrid composites have shown advantages for preparing hard coating layers. Especially, nano hybrid composite has low environmental pollution. It has high transparency, hardness, toughness, thermal dissociation temperature, hydrophobicity by using nano sized inorganic material. There are many ways in which these materials may be synthesized, a typical one being the use of silica and silanes using the sol-gel process. The structure of sol-gel silica evolves as a result of these successive hydrolysis and condensation reactions and the subsequent drying and curing. The sol-gel reactions are catalyzed by acids and produce silica sol solutions. The silica sol grows until they reach a size where a gel transition occurs and a solid-like gel is formed. Colloidal silica(CS)/silane sol solutions were synthesized in variation with parameters such as different acidity and reaction time. In order to understand their physical and chemical properties, sol-gel coating films were fabricated on glass. From all sol-gel solutions, seasoning effect of sol-gel coating layer on glass was observed.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2006년도 추계학술발표대회 및 제11회 신소재 심포지엄
• /
• pp.15.2-15.2
• /
• 2006

• 한국지진공학회논문집
• /
• 제7권2호
• /
• pp.59-66
• /
• 2003

본 연구에서는 나노기술을 이용하여 에너지 감쇄 기능을 활용한 내진용 감쇄기 개발에 대한 연구를 하였다. 구조물에 사용되는 기존의 유체 감쇄기를 대체하는 무기재료를 이용한 새로운 감쇄기에 대한 기초적 연구를 하였다. 완충역할을 하는 입자로는 미로구조를 가지는 실리카겔을 사용하였으며, 입자에 관련한 작동 유체로는 물을 사용하여 그 효과를 검증하였다. 콜로이드 감쇄기를 구현하기 위해서는 형성된 실리카 겔 입자의 표면을 유기 실리콘 매질을 이용한 소수화 코팅 처리를 하였다. 콜로이드 감쇄기의 이력곡선은 서로 다른 소수화 코팅 처리가 된 입자의 혼합과 소수화 처리시의 분자간 거리에 의해서 조절이 가능함을 알 수 있었다. 콜로이드 감쇄기의 에너지 소산양은 상이한 소수화 처리 정도와 서로 코팅처리량이 서로 다른 재료를 혼합함으로써 제어 할 수 있음을 확인하였다. 기존의 유압 감쇄기에서는 나타나지 않는 이러한 특징은 콜로이드 감쇄기가 충격 흡수 장치로 사용 가능하다는 사실을 입증한다.

• International Journal of Concrete Structures and Materials
• /
• 제9권2호
• /
• pp.207-217
• /
• 2015

The influence of powdered and colloidal nano-silica (NS) on the mechanical properties of cement mortar has been investigated. Powdered-NS (~40 nm) was synthesized by employing the sol-gel method and compared with commercially available colloidal NS (~20 nm). SEM and XRD studies revealed that the powdered-NS is non-agglomerated and amorphous, while colloidal-NS is agglomerated in nature. Further, these nanoparticles were incorporated into cement mortar for evaluating compressive strength, gel/space ratio, portlandite quantification, C-S-H quantification and chloride diffusion. Approximately, 27 and 37 % enhancement in compressive strength was observed using colloidal and powdered-NS, respectively, whereas the same was up to 19 % only when silica fume was used. Gel/space ratio was also determined on the basis of degree of hydration of cement mortar and it increases linearly with the compressive strength. Furthermore, DTG results revealed that lime consumption capacity of powdered-NS is significantly higher than colloidal-NS, which results in the formation of additional calcium-silicate-hydrate (C-S-H). Chloride penetration studies revealed that the powdered-NS significantly reduces the ingress of chloride ion as the microstructure is considerably improved by incorporating into cement mortar.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2005년도 하계학술대회 논문집 Vol.6
• /
• pp.35-37
• /
• 2005

100, 200nm 크기의 colloidal silica 각각에 나노 ceria 입자를 수열합성법으로 코팅하였다. Colloidal silica 입자에 ceria를 코팅 시 slurry의 pH조절과 수열처리에 이용하여 silica에 ceria가 코팅됨을 TEM과 zeta-potential을 이용하여 확인하였다. 연마 슬러리의 분산 안정성과 연마효율을 높이기 위하여 슬러리의 pH 는 9로 하였으며, 이때의 zeta-potential 값은 -25 mV이었다. 1 wt%로 제조된 연마슬러리를 이용하여, 4 inch $SiO_2$, $Si_3N_4$ wafer를 압력변화에 따른 연마특성을 관찰 하였다. Ceria coated colloidal silica 100 nm, 200 nm와 commercial한 $CeO_2$입자를 연마압력 6 psi로 oxide film을 연마한 결과 연마율이 각각 2490 ${\AA}/min$, 4200 ${\AA}/min$, 4300 ${\AA}/min$으로 측정되었다. 또한 $SiO_2$, $Si_3N_4$ film의 6 psi압력에서 ceria coated colloidal silica 100 nm, 200 nm와 commercial 한 $CeO_2$입자의 선택비는 3, 3.8, 6.7 이었다. 입자크기가 클수록 연마율이 높으며, Preston equation을 따라 연마 압력과 연마율이 비례하였다.