• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.51 no.4
• /
• pp.147-151
• /
• 2002

The resistances of metal2 contact to metall and poly Si are checked by various RF etch conditions in terms of pre-cleaning. The changes of resistance are evaluated by statistical analysis method(SAS) for the AC bias power, coil power and RF target. The contact area on poly Si is shown by TEM image and the distributions of contact resistance according to ar etch target and RTP are investigated. The RTP groups have larger variations than normal RF etch targets. When the RF etch target becomes lower and coil power becomes higher, the resistances of metal2 contact to metals and poly Si have lower contact resistance. But the condition of AC bias power did not satisfied low meta12 contacts resistance for metall and poly Si simultaneously. The R-square of ststistical analysis was 0.98 for resistances of meta12 contact to poly Si and 0.87 for resistances of meta12 contact to metall.

• Journal of the Semiconductor & Display Technology
• /
• v.2 no.3
• /
• pp.7-11
• /
• 2003

In this research, the etching characteristics of via contact and deep contact hole have been studied using multi-pole inductively coupled plasma(MICP) etching system. We investigated Plasma density of MICP source using the Langmuir probe and etching characteristics with RF frequency, wall temperature, chamber gap, and gas chemistry containing Carbon and Fluorine. As the etching time increases, formation of the polymer increases. To improve the polymer formation, we controlled the temperature of the reacting chamber, and we found that temperature of the chamber was very effective to decrease the polymer thickness. The deep contact etch profile and high selectivity(oxide to photoresist) have been achieved with the optimum mixed gas ratio containing C and F and the temperature control of the etching chamber.

• Korean Journal of Materials Research
• /
• v.14 no.8
• /
• pp.573-578
• /
• 2004

Newly developed silicide materials for ULSI should have the appropriate electrical property of low resistant as well as process compatibility in conventional CMOS process. We prepared $NiCoSi_x$ silicides from 15 nm-Co/15 nm-Ni/Si structure and performed contact dry etch process to confirm the dry etch stability and compatibility of $NiCoSi_x$ layers. We dry etched the photoresist/SiO/silicide/silicon patterns with $CF_4\;and\;CHF_3$ gases with varying powers from 100 to 200 W, and pressures from 45 to 65 mTorr, respectively. Polysilicon and silicon active layers without silicide were etched $0\sim316{\AA}$ during over etch time of 3min, while silicon layers with proposed $NiCoSi_x$ silicide were not etched and showed stable surfaces. Our result implies that new $NiCoSi_x$ silicides may replace the conventional silicides due to contact etch process compatibility.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.15 no.1
• /
• pp.7-14
• /
• 2002

In this paper, neutral networks are used to build models of oxide film etched In CHF$_3$/CF$_4$ with a magnetically enhanced reactive ion etcher(MERIE). A statistical 2$\^$4-1/ experimental design plus one center point was used to characterize relationships between process factors and etch responses. The factors that were varied include radio frequence(rf) power, pressure, CHF$_3$ and CF$_4$ flow rates. Resultant 9 experiments were used to train neural networks and trained networks were subsequently tested on its appropriateness using additionally conducted 8 experiments. A total of 17 experiments were thus conducted for this modeling. The etch responses modeled are dc bias voltage, etch rate and etch uniformity A qualitative, good agreement was obtained between predicted and observed behaviors.

• New & Renewable Energy
• /
• v.4 no.2
• /
• pp.74-80
• /
• 2008

To improve the blue responses of screen-printed single crystalline silicon solar cells, we investigated an emitter etch-back technique to obtain high emitter sheet resistances, where the defective dead layer on the emitter surface was etched and became thinner as the etch-back time increased, resulting in the monotonous increase of short circuit current and open circuit voltage. We found that an optimal etch-back time should be determined to achieve the maximal performance enhancement because of fill factor decrease due to a series resistance increment mainly affected by contact and lateral resistance in this case. To elucidate the reason for the fill factor decrease, we studied the resistance analysis by potential mapping to determine the contact and the lateral series resistance. As a result, we found that the fill factor decrease was attributed to the relatively fast increase of contact resistance due to the dead layer thinning down with the lowest contact resistivity when the emitter was contacted with screen-printed silver electrode.

• 한국신재생에너지학회:학술대회논문집
• /
• 2008.05a
• /
• pp.390-393
• /
• 2008

To improve the blue responses of screen-printed single crystalline silicon solar cells, we investigated an emitter etch-back technique to obtain high emitter sheet resistances, where the defective dead layer on the emitter surface was etched and became thinner as the etch-back time increased, resulting in the monotonous increase of short circuit current and open circuit voltage. We found that an optimal etch-back time should be determined to achieve the maximal performance enhancement because of fill factor decrease due to a series resistance increment mainly affected by contact and lateral resistance in this case. To elucidate the reason for the fill factor decrease, we studied the resistance analysis by potential mapping to determine the contact and the lateral series resistance. As a result, we found that the fill factor decrease was attributed to the relatively fast increase of contact resistance due to the dead layer thinning down with the lowest contact resistivity when the emitter was contacted with screen-printed silver electrode.

• Proceedings of the KIEE Conference
• /
• 1995.11a
• /
• pp.352-354
• /
• 1995

The optical and electrical properties of High Speed AlGaAs infrared LED by using metal wet etch process instead of metal lift-off process are investigated. The power out increases when metal contact is patterned by wet etch process. Forward voltage and Reverse voltage for metal wet etch process represent higher value than the metal lift-off process. The aging effect of power out also indicates good results with wet etch process. The wet etch process for metal contact reveals reliable LED device properties.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2015.08a
• /
• pp.136.2-136.2
• /
• 2015

반도체 제조는 chip의 성능 향상 및 단가 하락을 위해 지속적으로 pattern size가 nano size로 감소해 왔고, capacitor 용량은 증가해 왔다. 이러한 현상은 contact hole의 aspect ratio를 지속적으로 증가시킨바, 그에 따라 최적의 HARC (high aspect ratio contact)을 확보하는 적합한 dry etch process가 필수적이다. 그러나 HARC dry etch process는 많은 critical plasma properties 에 의존하는 매우 복잡한 공정이다. 따라서, critical plasma properties를 적절히 조절하여 higher aspect ratio, higher etch selectivity, tighter critical dimension control, lower P2ID과 같은 plasma characteristics을 확보하는 것이 요구된다. 현재 critical plasma properties를 제어하기 위해 다양한 plasma etching 방법이 연구 되어왔다. 이 중 plasma를 낮은 kHz의 frequency에서 on/off 하는 pulsed plasma etching technique은 nanoscale semiconductor material의 etch 특성을 효과적으로 향상 시킬 수 있다. 따라서 본 실험에서는 dual-frequency capacitive coupled plasma (DF-CCP)을 사용하여 plasma operation 동안 duty ratio와 pulse frequency와 같은 pulse parameters를 적용하여 plasma의 특성을 각각 제어함으로써 etch selectivity와 uniformity를 향상 시키고자 하였다. Selective SiO2 contact etching을 위해 top electrode에는 60 MHz pulsed RF source power를, bottom electrode에는 2MHz pulse plasma를 인가하여 synchronously pulsed dual-frequency capacitive coupled plasma (DF-CCP)에서의 plasma 특성과 dual pulsed plasma의 sync. pulsing duty ratio의 영향에 따른 etching 특성 등을 연구 진행하였다. 또한 emissive probe를 통해 전자온도, OES를 통한 radical 분석으로 critical Plasma properties를 분석하였고 SEM을 통한 etch 특성분석과 XPS를 통한 표면분석도 함께 진행하였다. 그 결과 60%의 source duty percentage와 50%의 bias duty percentage에서 가장 향상된 etch 특성을 얻을 수 있었다.

• Proceedings of the Korean Society Of Semiconductor Equipment Technology
• /
• 2003.05a
• /
• pp.12-17
• /
• 2003

본 연구에서는 MICP Etching system 을 이용한 Via contact 및 Deep contact hole etch process 특성을 연구하였다. Langmuir probe 를 이용한 MICP source 의 Plasma density & electron temperature 측정하였고 탄소와 플로우르를 포함하는 혼합 Plasma 를 형성하여 RF frequency, wall temperature, chamber gap, gas chemistry 등의 변화에 따른 식각 특성을 조사하였다. Plasma density 는 1000w 에서 $10^{11}$/$cm^3$ 이상의 high density plasma와 uniform plasma 형성을 확인하였고 $CH_{2}F_{2}$와 CO의 적절한 혼합비를 이용하여 Oxide to PR 선택비가 10 이상인 고선택비 조건을 확보하였다. 고선택비 형성에 따라 Polymer 형성이 많이 되었고 이를 개선하기 위하여 반응 챔버의 온도 조절을 통하여 Polymer 증착 방지에 효과적인 것을 확인하였다. MICP source를 이용하여 탄소와 플로우르의 혼합 가스와 식각 챔버의 온도 조절에 의한 선택비 증가를 확보하여 High Aspect Ratio Contact Hole Etch 가능성을 확보하였다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.11a
• /
• pp.583-586
• /
• 2000

The non-selective method by polishing after grinding was used widely to thinning of SDB SOI structures. This method was very difficult to thickness control of thin film, and it was dependent on equipments. However electrochemical etch-stop, one of the selective methods, was able to accurately thickness control and etch equipment was very simple. Therefore, this paper described with the effect of leakage current and electrodes on electrochemical etch-stop. Consequentially, PP(passivation potential) was changed according to the kinds of contact and contact sizes, but OCP(open current potential) was not change with range of -1.5~-1.3V