• The Research Journal of the Costume Culture
• /
• v.24 no.6
• /
• pp.817-824
• /
• 2016

The introduction of natural dyes into modern dye houses is very promising green chemistry concept that should be popularized more to reduce the dependency of leather dyeing on some toxic and non-biodegradable synthetic dyes. In this study, the properties of dyeing of cochineal on cow leather were evaluated. The proper dyeing conditions were identified with dye uptake (K/S values) depending on the colorant concentration, dyeing duration, dyeing temperature, and dye bath pH. For the proper mordanting conditions, color changes for different mordants were observed as $La^{*}b^{*}$ and H V/C values. Color fastness (light, rubbing, and dry cleaning) was also examined. Additionally, antibacterial properties and UV protection were examined. The results were as follows: The optimized dyeing conditions were 300% o.w.f., $40^{\circ}C$, 40 min., and pH 5. The cow leather color was red in the absence of mordanting, while it was red purple after being mordanted with Al and Cu, and purple mordanted with Fe. The K/S value of cow leathers increased in the order of the dyeing using $AlK(SO_4)_2$ > $CuSO_4$ > $FeSO_4$. The colorfastness to light and rubbing were reduced compared to original (untreated) cow leather. However dry cleaning fastness was very satisfactory, with a 4~5 rating. The dyed and pre-mordanting dyed cow leather showed excellent antibacterial properties.

• Journal of Fashion Business
• /
• v.16 no.4
• /
• pp.100-106
• /
• 2012

This research was carried out to find the mordant effect of Chestnut's inner skin on the cow leather dyed by Turmeric powder. The best proper mordanting conditions were examined by changing mordant method, concentration, temperature, bath ratio, time, and repetition. Also dyeability and surface color changes were evaluated by various mordanting methods. The optimum mordanting conditions of chestnut's inner skin extract on the cow leather were pre mordant, 80%, $50^{\circ}C$, 50:1, 40minutes, 4 repetition. The K/S values as a mordant were higher in pre mordant than post mordanting condition. Although the ${\Delta}E$ was slightly higher in post mordant than pre mordant, it was too small to find any means. The surface colors of all dyed cow leathers were yellow. Among light, dry cleaning, and abrasion fastnesses, only light fastness was increased one degree, others were same degrees.

• Journal of Fashion Business
• /
• v.17 no.4
• /
• pp.140-148
• /
• 2013

This research was carried out to find the dyeabilities and mordants effects of cow leather dyed with Lac powder. They were examined by changing dye concentration, dyeing temperature, bath ratio, dyeing time, and dyeing repetition. And K/S values and surface color changes were evaluated by various mordanting conditions. The optimum dyeing conditions of the cow leather dyed with Lac powder were 30%, $40^{\circ}C$, 30:1, 30minutes, and 4 repetitions. The K/S values were higher in post mordant than pre mordanting condition. The surface colors of dyed cow leathers were R and RP. The dye fastnesses increased in post Cu and Fe mordanting, as decreased in gallnut and chestnut's skin conditions.

• Journal of the Korean Society of Costume
• /
• v.58 no.9
• /
• pp.114-128
• /
• 2008

The current study aims to classify types of traditional fur Garments in Jeju into Dusik(hat), dress, Jokui(socks) and accessaries, and examine characteristics of them through demonstrative study focusing on collections of museums in Jeju. Dusik is a kind of hat for protection against the cold, and there are badger leather Gamtaes and cow hair Beonggeojis(fur hats). Especially leather gamtae was used to protect against the cold when people hunted roe deers in Mt. Halla. Beonggeoji was producted in the form of felt with fine hair collected coat-shedding of cows and dogs in spring, therefore it was too warm and practical to be damaged from storm or pressure. Fur coat is a general name of dress made of leather without hair. It is a kind of clothes with a hat worn while taking care of horses and cows. Also people wore dog leather topcoats and cow leather topcoats when they hunted in Mt. Halla. As for Jokui, there are leather Beoseon(socks) made of cow leather, leather shoes in the form of straw shoes, and leather Balle embracing the low half of the body warmly. Accessaries include a rectangular cow leather bag for storing an iron piece for making fire. These traditional fur robs in Jeju not only have practicality for protection against the cold, but also symbolized richness by using leathers of badgers, roe deers, etc. that were previous during that times. Also they used partially cut leather for decoration at the edge.

• Journal of Environmental Health Sciences
• /
• v.33 no.6
• /
• pp.488-492
• /
• 2007

The influence of additive materials including saw dust and cow manure in the ripening of leather sludge for the efficient vermisabilization was studied. The ripening characteristics of the leather sludge, the growth of earthworms in the growth bed and the by-products like cast were observed according to the mixing ratio of additive materials. When the mixed leather sludge of which the additive materials contents were over 20% were ripened for 50 days, the values of ORP and alkalinity were changed to the favorable ranges for earthworms, the positive (+) and below 1,000 mg/l as $CaCO_3$, respectively. The velocity of ripening improving the characteristics of the leather sludge was faster in the sludge mixed with cow manure than saw dust. This results could also be verified from the monitoring of the states of earthworm growth using the survival rate, the increase rate of lifeweight and the hatching rate of earthworm cocoon in the their growth bed packed with the ripened sludge. The values of CEC in cast, the vermi-stabilized sludge, were increased with the mixing ratio of additive materials, but the content of heavy metals was drcreased by the dilution effect and accumulation in the earthworm body. Above results show that the leather sludge might be efficiently stabilized by earthworms through the ripening for 50 days using additive materials. Cow manure can be used as a good additive materials for leather sludge as much as saw dust, and the optimum content of additive materials in the well-ripened leather sludge was about 30%.

• Journal of Institute of Convergence Technology
• /
• v.7 no.1
• /
• pp.7-10
• /
• 2017

In general, the shoe stretcher is utilized to stretching the leather of shoe upper in the longitudinal direction. In the capstone design class, we tried to make a shoe leather stretcher for the ball of foot. Since a natural cow leather was recovered in length according to relaxation time after stretched, it was difficult to predict the initial amount of set up of stretching. In this paper, tensile and relaxation experiments were conducted in order to predict the amount of initial stretching for appropriate tensile length. Apparatus of leather stretching was designed and strains of leather were measured according to relaxation times of 12, 18, 24 hours after stretching of 24 hours. It was revealed that the ratio of the final relaxed strain and the initial applied strain was about 0.404 with R-square of 0.990 for a shoe cow leather.

• Journal of Fashion Business
• /
• v.15 no.4
• /
• pp.182-189
• /
• 2011

Dyeing properties of cow leather was investigated with Tumeric powder. The effects of dyeing conditions, mordanting conditions, color change, and color fastnesses were studied. The results were as follows. The dye uptake increased as dye concentration, dyeing temperature, and bath ratio increased. In the effect of dyeing time, the highest dye uptakes showed at 20 minutes and decreased after that point. Pre mordanting was more effective than the post mordanting, and the dye uptakes improved all mordanted fabrics. The highest K/S values showed in pre-Al sample, and the lowest K/S values showed in post-Cu one. The values of Hunter on the samples were more changeable $L^*$ and $b^*$ than $a^*$, and all samples showed Yellow color in Munsell value. But the mordanting methods and mordanting agents were not significant in the color changes. The light fastness of dyed samples showed 1 grade, the dry cleaning and abrasion fastnesses did not improved except post-Fe wet sample.

• Carbon letters
• /
• v.11 no.1
• /
• pp.1-8
• /
• 2010

The adsorption of Acid Blue 92 onto three low cost and ecofriendly biosorbents viz., cow dung ash, mango stone ash and parthenium leaves ash and commercial activated carbon have discussed in this work. The ash of all the mentioned bio-wastes was prepared in the muffle furnace at $500^{\circ}C$ and all the adsorbents were stored in an air thermostat. Experiments at total dye concentrations of 10~100 mg/L were carried out with a synthetic effluent prepared in the laboratory. The parameters such as pH and dye concentration were varied. Equilibrium adsorption data followed both Langmuir and Freundlich isotherms. The results indicate that cow dung ash, mango stone ash and parthenium leaves ash could be employed as low-cost alternatives to commercial activated carbon in wastewater treatment for the removal of dye.

• Fashion & Textile Research Journal
• /
• v.15 no.4
• /
• pp.630-634
• /
• 2013

Cow leather coated with polyurethane film that contains various organic photosensitizers was investigated to demonstrate the antimicrobial properties in the application of the material to protective clothing and home appliances. To prepare the antimicrobial coating on leather surfaces with high potency against microbes, photoactive agents, such as benzophenone (BP), 4,4'-bis(dimethylamino) benzophenone (MK), 4,4'-dihydroxybenzophenone (DHBP) and methylene blue (MB), were incorporated into polyurethane-based coating solutions. The photoactive antimicrobial agent treated leather samples were characterized by SEM, color appearance, color fastness against abrasion, and antimicrobial tests. The optical properties of organic photosensitizers indicated that active UV absorbance ranges were different: BP (around 250 nm), MK (around 360 nm), DHBP (around 305 nm) and MB (around 295 nm &570 nm-685 nm). The intensity of the UV absorbance curve at the UVA light wavelength for the antimicrobial test showed the highest value with MK; subsequently, this was followed by MB, DHBP and BP in decreasing order. The treated-leather samples demonstrated excellent antibacterial activity under UVA light. The antimicrobial effects for the Staphylococcus aureus were superior to Escherichia coli. Moreover, the polyurethane finishing showed an effective durability to abrasion. The overall results indicated that DHBP is the most suitable PU coating additive to provide antimicrobial properties to leather as well as color and surface appearance than MK, MB, and BP.

• Journal of Fashion Business
• /
• v.20 no.4
• /
• pp.88-95
• /
• 2016

This paper investigated to the effectiveness of an eco-friendly method for oiling cow leather. After leather was lac-dyed with a vegetable leather processing solution and a mordant, olive oil was used to treat the leather. Changes in surface color and dyeability, light fastness, rubbing fastness, and water fastness were measured. An increase in dyeability caused by the mordant appeared in all the samples. The dyeability of leatger treated with Cu-mordant was higher than that treated with Fe-mordant and Al-mordant, and the three times greater than when no mordant was used. Dyeability after oiling more than doubled compare with before oiling. An increase in dyeability by oiling was highe greater than doubled compared with before oiling. The non-mordant-treated samples exhibited a 5-fold increase in dyeability, and the other samples showed more than two times more dyeability than did non-oiled samples. A color difference of more than 20.0-fold appeared in all samples, and the differences in lightness and chroma were greater than were the differences in other color factors. The colors after oiling were measured R, P, and PB. Light fastness improved in all samples after oiling, and all of the measurements were reduced in the order of Fe-mordant> Cu-mordant> Al-mordant ${\geq}$non mordant.