• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2005년도 춘계학술발표대회 개요집
• /
• pp.91-93
• /
• 2005

Forming sheet metal by laser-induced thermal stresses (laser forming) has been extensively studied, and the research has focused on two-dimensional geometries using a multi-pass straight line scan. Recently there came out some useful studies or three-dimensional laser forming which is applied to doubly curved shapes. The task of 3D laser forming sheet metal is to determine a set of process parameters such as laser scanning paths, laser power and scanning speed that will make a given shape. New method for laser forming of a doubly curved surface by using geometrical information was proposed and verified by experiments. This method shows good performance in the sense of calculation time and accuracy compared to the inherent strain method.

• 한국정밀공학회지
• /
• 제30권3호
• /
• pp.292-299
• /
• 2013

The measurement in the manufacturing process of curved ship hull plates still depends on wooden templates as a standard instrument. The metrology-enabled automation in the shipbuilding process has been challenged instead of line measurement with wooden templates. The developed measurement system consists of a CCD camera, multiple structured laser sources and 3-DOF motion device. The system carries out measurement of curved profiles for large scale plates by an optical triangulation method. The results of experiment conducted in a manufacturing shop demonstrate the accurate and robust performance.

• 대한치과교정학회지
• /
• 제18권2호
• /
• pp.289-308
• /
• 1988

The center of resistance is a important determining factor of tooth movement pattern. Laser speckle interferometry, recently developed for noninvasive measurement of small displacements (microns), was used to detect the center of resistance of a maxillary canine which has normal tooth axis and distal curved root in dry human skull. Laser holographic interferometry was used to verify the results of laser speckle interferometry The following result were obtained; 1. In measurement of the degree of rotation, center of resistance was localized when the traction line passed 4.4/18.0 level from alveola crest to root apex. 2. In measurement of the degree of tipping, center of resistance was localized when the traction line passed 4.6/18.0 level from alveola crest to root apex. 3. In holographic determination, the center of resistance was observed when the traction line passed between 3mm to 6mm level from alveola crest to root apex, therefore the results using laser speckle interferometry was coincided with holographic results.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2000년도 제15차 학술회의논문집
• /
• pp.347-347
• /
• 2000

Nowadays, the Laser image is used to realize multi-media show for events, an advertising media and 3D simulation, realization of video image and so on. It is a hot issue to realize the laser image like computer graphic image. The image used in laser projector is vector graphic image that is described by linking point to point. A computer makes this continuous vector graphic images so that the image shows as an animation. A control signal converted by a computer makes the laser projector draw image. Two motors and universal joint are used to realize 2D laser image in this study. Developing a controller applied Look-ahead algorithm and software to interface with personal computer, This study is the chief aim of improving difference of moving velocity that is appeared from edge of vector graphic image and disparity of graphic density.

• Transactions on Electrical and Electronic Materials
• /
• 제5권6호
• /
• pp.219-222
• /
• 2004

This paper discovers that there are some peculiar properties that can remove holography grating, which was made in chacogenide thin film by impressed voltage. The thin films were used are $As_{40}Ge_{10}Se_{15}S_{35}$, and we use He-Ne laser in order to form thin films. I-V curved line in a thin film before a lattice was made has the critical point, about 3.7 V. Moreover, the I-V curved line increased current intensity at over 4 V after it made thin film. In addition, while holography grating is being made, and when it has the highest diffraction efficiency, a lattice can be deleted if put more voltage into it.

• 한국기계가공학회지
• /
• 제4권1호
• /
• pp.37-42
• /
• 2005

The localization of manufacturing technique development is actualizing for low cost with supplies of display devices. We need more high cutting technique because consumers want flat glasses of various sizes. Recently, most general two methods are normal wheel cutting and laser cutting, but both of them have some faults. First, the wheel cutting has cracks and sharp edges of sections. Second, it is easy for laser cutting to cut curved lines. however, it has thermal damage and low traverse speed. I suggest a new cutting method by high-wave frequency vibration wheel cutting(HFVC), which is good for quality improvement. Vertical cracks and crack depth is observed, after HFVC. When the average of the crack depth is $30{\mu}m$ and the average of the wallner liner depth is $200{\mu}m$, it has the most high quality of the sections in this experiment. As a result, when we consider between the normal wheel cutting method and the HFVC method, the latter has low cracks and good quality.

• Journal of Computational Design and Engineering
• /
• 제1권3호
• /
• pp.202-212
• /
• 2014

To survive in the current shipbuilding industry, it is of vital importance for shipyards to have the ship components' accuracy evaluated efficiently during most of the manufacturing steps. Evaluating components' accuracy by comparing each component's point cloud data scanned by laser scanners and the ship's design data formatted in CAD cannot be processed efficiently when (1) extract components from point cloud data include irregular obstacles endogenously, or when (2) registration of the two data sets have no clear direction setting. This paper presents reformative point cloud data processing methods to solve these problems. K-d tree construction of the point cloud data fastens a neighbor searching of each point. Region growing method performed on the neighbor points of the seed point extracts the continuous part of the component, while curved surface fitting and B-spline curved line fitting at the edge of the continuous part recognize the neighbor domains of the same component divided by obstacles' shadows. The ICP (Iterative Closest Point) algorithm conducts a registration of the two sets of data after the proper registration's direction is decided by principal component analysis. By experiments conducted at the shipyard, 200 curved shell plates are extracted from the scanned point cloud data, and registrations are conducted between them and the designed CAD data using the proposed methods for an accuracy evaluation. Results show that the methods proposed in this paper support the accuracy evaluation targeted point cloud data processing efficiently in practice.

• 비파괴검사학회지
• /
• 제25권2호
• /
• pp.95-102
• /
• 2005

원자력 발전소의 많은 배관부는 고온, 고압환경에서 적용되고 있어 환경적 및 기계적 요인에 의하여 부식결함이 빈번히 발생하고 있다. 이와 같은 부식 결함은 초음파 기법 등에 의하여 평가되어야 하고, 본 연구에서는 주사형 레이저 유도 초음파(SLS) 기법을 도입하여 배관부 부식결함의 영상화 기법을 적용하였다. 본 기법은 표면이 거칠거나 배관재와 같은 곡면의 표면에서 적용할 수 있는 장점이 있다. 한편 기존의 주사형 초음파 기법은 초음파 센서와 검사대상체 사이의 초음파 전달 매개체를 확보하기 위하여 시험편이 수침되거나 워터젯을 이용하였으나 주사형 레이저 초음파 기법은 광학적 기법을 이용하여 초음파를 발생시키므로 비접촉 방법에 의한 주사 이미지 획득이 가능하다. 따라서 본 주사형 레이저 초음파 기법은 복잡한 구조물의 검사, 비접촉 원격 및 고화질의 결함 이미지 탐상이 가능하다. 본 연구에서는 배관 결함의 검출능 향상을 위하여 결함 영상 획득에 있어서 다양한 조건의 레이저 유도 초음파 발생 기법을 적용하였고, 배관에 존재하는 응력부식 균열의 결함 영상을 얻게 되었다.

• 한국광학회지
• /
• 제11권2호
• /
• pp.80-84
• /
• 2000

Diamond turning machine으로 알루미늄을 가공하여 f/1.5, 구경 50mm인 포물명경을 제작하였다. 이진위상(binary phase) 홀로그램으로 포물면경 현상측정을 위한 computer generated hologram(CGH)을 encoding하였으며 staircase encodling 방법으로 간섭무늬 곡선의 직선근사를 하였다. 간섭무늬 데이터를 포스트스크립트(PostScript) 파일로 변환한 후 CGH 원도를 레이저 프린터로 확대 출력하고 축소 촬영하여 CGH를 제작하였다. 측정부(viewing arm)에 CGH가 위치하는 Twyman-Green 간섭계를 구성하여 포물면경의 표면형상을 측정하였다. 측정결과를 직접표면형상측정법 및 간섭계를 이용한 자동시준법의 측정 결과와 비교하고 오치를 분석하였다.