• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1996.04a
• /
• pp.704-708
• /
• 1996

The elastic dynamic crack curving could be obtained by controlling the loading rate, the initial crack-tip blunting to store much energy before crack initiation and the magnitude of reflected wave from finite boundaries. However there is no theoretical and experimental elastic-plastic dynamic curving study. This paper proposes a specimen geometryfor a study of dynamic elastic-plastic crack curving and presents a preliminary result. The specimen has a blunt physical crack tip on a side, and a round notch tip on the other side. From the experiment using this specimen, it is found that the narrow plastic zone ahead of the round notch tip produces the change of load direction and anti-symmetricity of the dynamic isochromatics, and each result causes the crack curving phenomenon. After a certain time, as the elastic-plastic crack gets close to the round notch tip near, the degree of the crack curving get larger. The elastic reack curving propagates more sensitively to the surround of crack tip than the plastic crack curving does. The cynamic elastic-plastic crack curving is found to be proportional to the CTOA(the crack tip opening angle). The dynamic elastic-plastic crack may propagate in the direction perpendicular to the loading. An apparant strip yield zone which is similar to the Dugdale strip yield zone is noted ahead of the physical crack tip.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1997.10a
• /
• pp.49-52
• /
• 1997

The kinematically admissible velocity field is developed for the analysis of the curving of an eccentric extrusion. The curving of product in extrusion is caused by the difference of the linearly distributed longitudinal velocity on the cross-section of the workpiece at the dies exit. The result of the analysis show that the curvature of product increases with the increase in eccentricity of gravity center of the cross-section of the workpiece at the die entrance from that of the cross-section at the die exit. It also increase with the die land dimension. By the DEFORMTM-3D analysis, the curving of T-shaped product in extrusion is changed by the eccentricity, die land length and the friction constant. The result of the analysis by DEFORMTM-3D software shows that the curvature of circular shaped product increases with the eccentricity. The two analysis and one experiment show the curving phenomenon in eccentric extrusion process.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.19 no.1
• /
• pp.85-93
• /
• 2009

There are many curves in Seoul subway system. Therefore, the noise from subway system in curved line gives displeasure to passenger. The subway noise in curved line is affected not only by rail condition but also wheel condition and dynamic characteristics. The railway curving noise can be divided into 2 categories. The first is the noise due to stick-slip between wheel tread and rail head, and the second is one by wheel flange contact on rail side. Because of these phenomena - stick-slip and wheel flange contact - wheels are worn seriously. In this study the curving noise was reviewed by using eigen-mode of wheel and waterfall plot which shows noise level in time-frequency domain. And also those were reviewed in viewpoint of stick-slip noise and wheel flange contact noise. Finally, the relationship between curving noise and wheel wear was studied.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.8 no.6
• /
• pp.526-535
• /
• 1984

An analysis has been developed to evaluate the lateral stability and curving performance of rigid bogies having side bearer friction. A bogie model having 2 degree of freedom in lateral and yaw direction is utilized, and it's validity is examined. The effect of various design parameters are investigated. It is shown that there is no change in curving performance as lateral load is varied, and that varing side bearer friction has no significant effect on both critical speed and curving.

• Journal of Industrial Technology
• /
• v.26 no.B
• /
• pp.43-51
• /
• 2006

Through the result of calculating the deviation between the value calculated from two-dimensional number formula, one-dimensional number interpretation, and curving part water surface type calculation method, we could confirmed that the deviation is reduced more than 50% when we use curving part water surface type calculation method. Also it was confirmed that there occurs the reduction rate of maximum 59% as the result of comparing with one-dimensional number interpretation since the reduction rate of safe room height was 20%, in 500 CMS of flood water quantity when we planted the construction of levee by curving part water surface type calculation method. And therefore, we have confirmed that the curving water surface type calculation method can be used as a simple formula in rivers with water quantity less than 500 CMS that flows in and out in Jess than 90 degree angle.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1997.10a
• /
• pp.45-48
• /
• 1997

The kinematically admissible velocity field is developed for the eccentric extrusion of circular shaped products. The curving of product in extrusion is caused by the difference of the linearly distributed longitudinal velocity on the cross-section of the workpiece at the dies exit. The results of the eccentric extrusion by upper bound analysis show that the curvature of product increases with the increase in eccentricity of gravity center of the cross-section of workpiece at dies entrance from that of the corss-section at the dies exit end. By the DEFORMTM-3D analysis, the curving of circular shaped product in extrusion is changed by the eccentricity, die land length and the die length. The result of the analysis by DEFORMTM-3D software shows that the curvature of circular shaped product increases with the eccentricity. The two analysis and one experiment show the curving phenomenon in eccentric extrusion process.

• Steel and Composite Structures
• /
• v.17 no.6
• /
• pp.951-965
• /
• 2014

Point bending is commonly used for cambering and curving steel girders to large radii. In this system, a hydraulic ram or press is used to apply concentrated loads at selected points to obtain the required vertical (cambering) or horizontal (curving) curved profile from induced permanent deformations. This paper derives closed form solutions that relate loads to permanent deformations for horizontally curving wide flange steel beams based on their post-yield response. These solutions are presented in a parametric form to identify the relationship between key variables and their impact on the accuracy of the curving operation. It is shown that point bending could yield parabolic curved profiles that are within 1% of a desired circular curve if the span length to radius of curvature ratio (L / R) is less than 1.5 and the point loads are spaced at one third the beam length. Safe limits are then established on loads, strains and curvatures to avoid damaging the steel section. This leads to optimization of the point bending operation for inducing a circular profile in wide flange steel beams of any size.

• Proceedings of the KSR Conference
• /
• 1999.05a
• /
• pp.192-199
• /
• 1999

In this study, we have analyzed the running performance of Mugungwha coach in curves to grasp the problems relating to this coach's curving performance and present improvement plans. Simulations and tests to analyze curving performances are carried out, and through this Process we could prepare a plan to improve the running performance in operation.

• Transactions of Materials Processing
• /
• v.7 no.2
• /
• pp.177-185
• /
• 1998

The kinematically admissible veolcity field is developed for the shapes of dead metal zone and the curving velocity distribution in the eccentric plane dies extrusion. The shape of dead metal zone is defined as the boundary surface with the maximum friction constant between the deformable zone and the rigid zone. The curving phenomenon in the eccentric lane dies is caused by the eccentricity of plane dies. The axial velocity distribution in the plane dies is divided in to the uniform velocity and the deviated velocity. The deviated velocity is linearly changed with the distance from the center of cross-section of the workpiece. The results show that the curvature of products and the shapes of the dead metal one are determined by the minimization of the plastic work and that the curvature of the extruded products increase with the eccentricity.

• Proceedings of the KSR Conference
• /
• 2007.05a
• /
• pp.715-721
• /
• 2007

On a conventional rail vehicle, passive primary suspensions stabilize wheelsets in the longitudinal and yaw direction. However, these suspensions reduce the natural curving ability due to the profile of the wheels. Stabilizing and steering of the wheelsets generate the conflict problems in design process. Therefore, most systems are designed to guarantee the stability in spite of decreased curving performance. As a result, severe wear of the wheels and rails occur on tight curves and squeal noise on curving is high. Active steering has been proposed to satisfy stabilizing and steering performance simultaneously. This paper describes the possibility investigation about the application of the active steering bogie for a urban railway vehicle. Vehicles run on an amount of tight curves at mid or low speed in urban railways. Thus, it is important to reduce the wear and squeal noise between wheels and rails. Simulations show that active steering can be reduce the wear and squeal noise significantly compared to conventional systems.