• 대기
• /
• 제27권4호
• /
• pp.445-453
• /
• 2017

This study investigates turbulent flow around a square cylinder mounted on a flat surface at high Reynolds number using a large-eddy simulation (LES) model, particularly focusing on vortex streets behind the square cylinder. Total 9 simulation cases with different inflow wind directions, inflow wind speeds, and cylinder widths in the x- and y-directions are considered to examine the effects of inflow wind direction, speed, and cylinder widths on turbulent flow and vortex streets. In the control case, the inflow wind parallel to the x-direction has a maximum speed of $5m\;s^{-1}$ and the width and height of the cylinder are 50 m and 200 m, respectively. In all cases, down-drafts in front of the cylinder and updrafts, wakes, and vortex streets behind the cylinder appear. Low-speed flow below the cylinder height and high-speed flow above it are mixed behind the cylinder, resulting in strong negative vertical turbulent momentum flux at the boundary. Accordingly, the magnitude of the vertical turbulent momentum flux is the largest near the cylinder top. In the case of an inflow wind direction of $45^{\circ}$, the height of the boundary is lower than in other cases. As the inflow wind speed increases, the magnitude of the peak in the vertical profile of mean turbulent momentum flux increases due to the increase in speed difference between the low-speed and high-speed flows. As the cylinder width in the y-direction increases, the height of the boundary increases due to the enhanced updrafts near the top of the cylinder. In addition, the magnitude of the peak of the mean turbulent momentum flux increases because the low-speed flow region expands. Spectral analysis shows that the non-dimensional vortex generation frequency in the control case is 0.2 and that the cylinder width in the y-direction and the inflow wind direction affect the non-dimensional vortex generation frequency. The non-dimensional vortex generation frequency increases as the projected width of the cylinder normal to the inflow direction increases.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1995년도 춘계학술대회 논문집
• /
• pp.278-282
• /
• 1995

We developed a part of storke sensing cylinder using magnetic sensor and estimated is performance. In this paper, for the performance estimation of stroke sensing cylinder. We consist of hydrallic system using solenoid valve with ON/OFF motion. In order to the control of solenoid valve for the position control of cylinder rod, PWM (Pulse Width Modulation) method which modulates time pulse width in proportion to error was used. A performance of cylinder rod with magnetic scales was evaluated by its hydraulic system.

• 설비공학논문집
• /
• 제22권8호
• /
• pp.523-529
• /
• 2010

We investigate two-dimensional laminar flow around rectangular cylinders placed in a uniform stream. Numerical simulations are performed, using finite volume method, in the ranges of $50{\leq}Re{\leq}150$ and $0.1{\leq}W/H{\leq}1.0$, where Re and W/H are the Reynolds number and the width-to-height ratio, respectively. The immersed boundary method is used to handle the rectangular cylinder in a rectangular grid system. Comparisons with the previous results show good agreement in Strouhal number, drag and lift coefficient. The present study reports the detailed information of flow structure at different width-to-height ratios in the ranges of $50{\leq}Re{\leq}150$.

• International Journal of Automotive Technology
• /
• 제7권1호
• /
• pp.109-114
• /
• 2006

Half-beads of multi-layer-steel cylinder head gaskets take charge of sealing of lubrication oil and coolant between the cylinder head and the block. Since the head lifts off periodically due to the combustion gas pressure, both the dynamic sealing performance and the fatigue durability are essential for the gasket. A finite element model of the halfbead has been developed and verified with experimental data. The half-bead forming process was included in the model to consider the residual stress effects. The model is employed to assess the dependence of the sealing performance and the fatigue durability on the design parameters of half-bead such as the width and height of bead and the flat region length. The assessment results show that the sealing performance can be enhanced without significant deterioration of the fatigue durability in a certain range of the half-bead width. In the other cases the improvement of sealing performance is accompanied by the loss of the fatigue durability. Among three parameters, the bead width has the strongest influence.

• Journal of Advanced Marine Engineering and Technology
• /
• 제15권3호
• /
• pp.45-56
• /
• 1991

This paper describes characteristics of the flow pattern of the flow past a rectangular cylinder experimentally investigated. The width-to-length ratio of the section varried from 2 to4. For the statistical treatment, autocorrelation coefficient, probability density function and power spectral density function are obtained by the digital processing technic through on-line system with a hot wire anemometer. As a results, it was found that strong periodic coherent eddies structure is sustained to about 20H downstream from the cylinder. And nearer the cylinder in the wake, the number of turbulent eddies of a large scale coherent structure are comparatively much more dominant than that of a small scale one. By the analysis of power spectrum, It was cleared that there exists a certain range of the width to length ratio between 2.5 and 3 of which the flow pattern changes abruptly with a sudden discontinuity in Strouhal number.

• 한국자기학회지
• /
• 제17권2호
• /
• pp.103-107
• /
• 2007

본 연구에서는 고체 안에 둘러쌓인 감마선 원천핵 $^{133}Cs$를 금판(gold plate)으로 된 실린더 안에 놓았을 때 첫 여기상태인 81 keV 에너지 준위폭이 더 좁아짐을 볼 수 있었다. 이러한 결과는 에너지 준위의 수명이 연장된 것을 의미한다. 두께 0.5 mm, 길이 5 cm, 반경 1 mm의 실린더를 사용했을 때 4.2 K에서 에너지 준위폭은 6.1 %정도 좁아지는 결과를 얻었다.

• 한국자동차공학회논문집
• /
• 제8권6호
• /
• pp.51-59
• /
• 2000

In-cylinder spray flow motion plays an important in the adjustment of mixture preparation with a fundamental spray characteristics and in-cylinder flow field well in direct-injection gasoline engine. In this study, the fundamental spray characteristics such as mean drop size, velocity distribution, spray angle were measured and in-cylinder spray flow motion was visualized in order to optimize intake port, piston top land and combustion chamber shapes in the development stage of mass-produced G야 engine. For these experiments, the PDPA measurements and Mie scattering technique were used for detailed spray characteristics and in-cylinder spray motions were obtained by use of ICCD camera through the single-cylinder optical engine. From the experimental results, the test injector shows a good low-end linearity between the dynamic flow and fuel injection pulse width and the fuel spray of 20mm or less in SMD with good spray symmetry. In addition, the in-cylinder tumble flow has more effect on the homogeneous mixture formation than that of in-cylinder swirl flow at early injection mode and the in-cylinder swirl flow plays a better role of stratified mixture preparation than tumble flow at late injection mode.

• Journal of Mechanical Science and Technology
• /
• 제15권12호
• /
• pp.1784-1793
• /
• 2001

The flow fields around an elliptic cylinder of axis ratio AR=2 adjacent to a free surface were investigated experimentally using a water channel. The main objective is to understand the effect of the free surface on the flow structure in the near-wake. The flow fields were measured by varying the depth of cylinder submergence, for each experimental condition, 350 velocity fields were measured using a single-frame PIV system and ensemble-averaged to obtain the spatial distribution of turbulent statics. For small submergence depths a large-scale eddy structure was observed in the near-wake, causing a reverse flow near the free surface, downstream of the cylinder. As the depth of cylinder submergence was increased, the flow speed in the gap region between the upper surface of the cylinder and the free surface increased and formed a substantial jet flow. The general flow structure of the elliptic cylinder is similar to previous results for a circular cylinder submerged near to a free surface. However, the width of the wake and the angle of downward deflection of the shear layer developed from the lower surface of the elliptic cylinder are smaller tan those for a circular cylinder.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 춘계학술대회논문집A
• /
• pp.321-325
• /
• 2000

Gasket of vehicle engine maintains airtight between cylinder head and engine block under high temperature and pressure, and plays important role in heat conduction of engine. And the characterization of the nonlinear behavior of metal gasket fer various bead shapes is very important as basic research for estimation of gasket durability. But it is very difficult to analyze the behavior of gasket In real experiment. In this paper, to analysis effects of the bead shape on the nonlinear behavior of cylinder head gasket under uniform pressure, the virtual experiment using the nonlinear finite element method was performed. Results are analyzed with residual deformation and the sealing pressure. With the increase of the height and the width of bead, the residual deformation and the sealing pressure increase. And if the height is very high and the width is very narrow, the wrinkles are occurred in the gasket while working.

• 대한기계학회논문집B
• /
• 제20권1호
• /
• pp.369-376
• /
• 1996

Variations of the drag and lift forces of a circular cylinder in a planar turbulent jet were experimentally investigated. The force was directly measured using the load cell and estimated by integrating the pressure distribution on the cylinder. As the cylinder moves outward from the center of the jet, the direction of lift force changes and the drag force decreases. Reynolds number, the ratio of cylinder's diameter to half width of jet had effect on maximum drag coefficient and the location where the direction of lift changes.