• Design & Manufacturing
• /
• 제14권3호
• /
• pp.37-43
• /
• 2020

Progressive drawing processing is one of the manufacturing processes used to mass-produce a variety of products on the industrial site. In this study, the goal is to achieve a uniform product thickness of at least 1.3mm by reducing the wall thickness of the coupler parts used in automotive air conditioning systems to within 15% using A5052-H32 materials. The progressive die was designed using Blank's law of volume invariance. Due to the characteristics of the drawing process, the material thickness in the punch R part decreases and the thickness in the die R part increases. When designing the progressive die of the coupler part, an ironing method, a push back method, and a stand-alone die pad method were applied to each process to design a mold in consideration of the drawing rate and to artificially adjust the thickness change. The suitability of the method used in die design was investigated by measuring the thickness change of forming parts for each process. In the final part, it was confirmed that the thickness measurement values of the five regions of a radial line were implemented as 1.34-1.36 mm.

• 대한치과보철학회지
• /
• 제37권5호
• /
• pp.640-650
• /
• 1999

As an optimal quality of the restorations, there should be a least amount of seating discrepancy between the casting and abutment teeth. However, high viscosity of the cementing medium and its resulting thickness may prevent complete seating of the restoration. The use of die spacing material provides adequate internal relief for the cementing medium. The purpose of this study is to compare the thickness of three commonly used die spacing materials. Materials and Methods: Stone plates were fabricated and divided into 12 sections to be painted with die spacers. Tru-Fit, Whip-Mix and Belle do St. Claire die spacer which are commonly used in dental practice were tested in this study. Each die spacers were painted layer by layer according to the manufacturer's recommendation. The average thickness of each die spacers were measured with light microscope(${\times}100$) and compared between them. Results and Conclusions. A silver-colored Tru-Fit die spacer has the lowest value of thickness without statistical significance comparing with a gold-colored Tru-Fit die spacer and a gray layer of Whip-Mix die spacer has the highest value of thickness without any statistical significance comparing with Belle de St. Claire die spacer. Three and four layers of Tru-Fit die spacer and two layers of Whip-Mix and Belle de St. Claire die spacers seem to be in the acceptable range of thickness of 25 to $45{\mu}m$ for optimal seating of the restorations. The standard experimental design and method should be fur thor evaluated for more consistent and objective results.

• 소성∙가공
• /
• 제19권8호
• /
• pp.447-451
• /
• 2010

In this paper, a useful die system for warm plate forging of a large axle housing of heavy-duty trucks is presented. A die system composed of material flow guide pin as well as upper die and lower die is proposed to reduce the inherent thickness reduction along the bent corner of the product which deteriorates structural strength and fatigue life in its service. The role of the pin assembled in the upper die is to prevent formation of sharp corner in early forming stage and to supply material in the lower die cavity sufficient enough to thicken the bent corner at the final stroke. The mechanism of the die system is given and its effect on corner thickness of the product is revealed by two-dimensional finite element analysis under plain strain assumption. Three-dimensional finite element solutions are also given to verify validity of the two dimensional approach and to show the mechanics of the die system in detail. The die system has been successfully applied to manufacturing the axle housing of heavy-duty trucks.

• 소성∙가공
• /
• 제18권2호
• /
• pp.156-159
• /
• 2009

Slot coating has been wide spread in photo-resist coating on the glass for liquid crystal display. Die in slot coater consists of manifold and land. Material comes in inlet of the die and flow into the manifold and then flow out through the land. The coating thickness variations along the die length depend upon inside of die design such as manifold and die land. However the coating thickness variations along the moving direction(coating direction) of the coater depend upon the operational conditions of coater as well as die lip design. The coating behaviors including atmospheric air have been investigated in this study. Die geometries considered in this study were nozzle gap and length of the die lip. Coating gap and coating speed were the variables fur coating operational conditions. When the nozzle gap and length of die lip increased climbing effect of PR on the downstream die lip was reduced. Subsequently uniformity of coating thickness improved. Uniformity of coating thickness also enhanced as coating gap and coater speed increased. The uniformity of coating gap was related to the velocity vector distributions on the coating surface.

• 대한안전경영과학회지
• /
• 제17권2호
• /
• pp.235-240
• /
• 2015

Using a progressive die of the multi-stage drawing product, It was experiments for the Influence of the Products Roundness on the die pad process Safety die model, obstacle countermeasure research safety die design When the die pad is independent structure, Sidewall thickness of the inside 2stage, 3stage, 4stage of the product is thicker, the thickness of the inside 1stage and the bottom is thinner. it was become unstable beacuse the inside 1stage related to the Products Roundness is thinner. When the die pad is Integrated structure, Sidewall thickness of the inside 1stage, 2stage of the product is thicker, and Sidewall 3stage and 4stage was a thin. it was become unstable beacuse the inside 3stage related to the Products Roundness is thinner. Therefore, The appropriate combination of and integrated independent is required for each process.

• Design & Manufacturing
• /
• 제13권1호
• /
• pp.31-35
• /
• 2019

For manufacturing upper housing product of mechanical control valve, the progressive drawing process was conducted experimental. Then, the center of the product was cut to measure the thickness of the product. As a result, the following conclusions were obtained. By means of a stand-alone pad provided with sufficient pressure, it is possible to prevent the occurrence of wrinkles in the die pad product of the drawing process. As a result of the experiment, it was considered that the flange bottom of the product and the lower edge of the product are made thick in thickness, the top edge and the top surface are thin. It is considered that this is due to the size and roughness of the entrance edge radius of the die in the drawing process, and the inflow of the material by the die pad.

• 대한치과보철학회지
• /
• 제32권2호
• /
• pp.212-224
• /
• 1994

The purpose of this study was to evaluate and compare film thickness of five kinds of resin luting cements [Comspan, Panavia Ex, Maryland bridge adhesive, All-bond C & B cementation kit, and Super-bond C & B]. Zinc-phosphate cement and glass-ionomer cement were used as the control group. In order to measure the film thickness the methods used were in broad compliance with ADA Specification No. 8, a tapered-die system that simulates clinical conditions more closely, and the connected tapered-die system that simulates bridge conditions. The inorganic filler size of resin cements was also examined with scanning electron micrographs. The results were obtained as follows ; 1. The film thickness of resin cements was increased in the order of Comspan, Panavia Ex, Super-bond C & B, Maryland bridge adhesive, and All-bond C & B cementation kit. Maryland bridge adhesive and All-bond C & B cementation kit showed significantly higher film thickness than the control group(p<0.01). 2. For all resin cements, there was a significant difference of film thickness between the ADA method and the tapered-die system. Generally, the tapered-die system demonstrated lower film thickness than the ADA method(p<0.01). 3. There was no significant difference in film thickness between the tapered-die system and the tapered-die bridge system in all resin cements(p<0.01). 4. The scanning electron microscope showed that the cement with larger filler had a tendency to be higher in film thickness.

• Design & Manufacturing
• /
• 제2권5호
• /
• pp.21-24
• /
• 2008

On this study, injection molding product of rectangular tray structure with thickness 0.25mm and aspect ratio(length/thickness) approximately 150 conducted. Technical aspects were reviewed on mold-die design and injection molding conditions. To have a thin-membraned plastic part, short-shot, shrinkage, twist, whitening and flash problems were considered and resolved. After measuring products, validity of this study and future improvement were discussed.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집D
• /
• pp.311-318
• /
• 2001

A three-dimensional numerical analysis of the flow and heat transfer characteristic of wood-flour-filled polypropylene melt in an extrusion die was carried out Used for this analysis were Finite Concept Method based on FVM, unstructured grid and non-Newtonian fluid viscosity model. Temperature and flow fields are closely coupled through temperature dependent viscosity and viscous dissipation. With large Peclet, Nahme, Brinkman numbers, viscous heating caused high temperature belt near die housing, Changing taper plate thickness and examining some predefined parameters at die exit investigated the effect of taper plate on velocity and temperature uniformities. In the presence of taper plate, uniformity at die exit could be improved and there existed an optimum thickness to maximize it.

• 한국산학기술학회논문지
• /
• 제12권2호
• /
• pp.565-570
• /
• 2011

본 연구는 파인 블랭킹(fine blanking) 프레스로부터 기능면으로 사용되는 100% 매끄러운 전단면을 얻는 파인 블랭킹 공정에서 다이 롤(die roll) 크기를 최소화하기 위한 목적으로 실험을 통해 다이 챔퍼(die chamfer) 형상에 따라 성형되는 제품의 다이 롤 크기 변화를 검토한 것이다. 다이 챔퍼가 다른 여러 가지 다이 편(die insert)을 제작하여 파인 블랭킹 실험을 실시한 후 다이 챔퍼 형상에 따른 다이 롤 크기를 측정 분석하여 두께 방향 다이 롤 크기의 경향을 파악하였다. 이 연구 결과는 파인 블랭킹 판재 성형에서 두께 방향 다이 롤 크기를 최소화하기 위한 다이챔퍼 설계에 유용하게 적용될 것으로 판단된다.