• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.29 no.10
• /
• pp.799-804
• /
• 2018

In this paper, a method for measuring the dielectric constant of a planar dielectric substrate using the free space material constant measurement method in a general measurement environment is proposed. Two horn antennas and a network analyzer were used for S-parameter measurement and the transmission and reflection coefficients of a planar dielectric substrate were calculated from the measurement results. To obtain a reliable dielectric constant in a low-precision-measurement environment, only the magnitude of the transmission coefficient, which has a small error due to the measurement environment, is used for dielectric constant estimation. Finally, the dielectric constant is determined by comparing the measured results at different frequencies.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.15 no.1
• /
• pp.9-15
• /
• 2011

This paper suggested the fast and easy method of the dielectric constant measurement for planar dielectrics using a microstrip line. The complex permittivity and permeability were presented by the first reflection and transmission coefficient which were derived from the scattering parameters. This method was verified by the measurement of a known planar dielectric using a microstrip line. This method can be applied to the dielectric constant measurement of unknown planar dielectric.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2000.11a
• /
• pp.243-247
• /
• 2000

In this parer, Q-factor measurement method for a dielectric resonator in an MIC environment using the effective dielectric constant is proposed. The effective dielectric constant technique is applied to both radial and axial directions. The proposed method shows that the accuracy of the Q-factor measurement is to be improved with 2% ～ 3% relative error.

• Tribology and Lubricants
• /
• v.22 no.5
• /
• pp.260-268
• /
• 2006

The dielectric constants of used gasoline engine oils were obtained at a few temperatures and a frequency. Through analyzing the characteristics of dielectric constant, the related correlation between the changes in dielectric constants of oil and the degree of oil deterioration is going to be found. The dielectric constant was calculated using cross capacitances measured by a sensor tube. As results of the measurement of the fresh engine oil's dielectric constant, it was found that the value of dielectric constant was set down below $60^{\circ}C$ regardless changing frequency. Further, above 6 kHz, the dielectric constant was set down even if temperature was above $100^{\circ}C$ Therefore, for the measurement of used oils, it was selected the frequency of 6 kHz,,and the temperature of $80^{\circ}C$ preventing a certain ionic-conduction effects on the measured dielectric constant and the evaporation of a certain fluid mixed with engine oil. Specially, the effects of the mixing fluid like coolant, water and fuel on the fresh engine oil's dielectric constant were studied. It was found that the oil mixed with coolant showed the highest value, next water, and the lowest fuel. As results of the measurement of the used engine oil's dielectric constant, it was found that the possible changed rate of the used engine oil's dielectric constant based on the warning limit for engine oil in service was below 4% for gasoline engine oil.

• Tribology and Lubricants
• /
• v.22 no.5
• /
• pp.290-300
• /
• 2006

The dielectric constants of used diesel engine oils were obtained at a few temperatures and a frequency. Through analyzing the characteristics of dielectric constant, the related correlation between the changes in dielectric constants of oil and the degree of oil deterioration is going to be found. The dielectric constant was calculated using cross capacitances measured by a sensor tube. As results of the measurement of the fresh engine oil's dielectric constant, it was found that the value of dielectric constant was set down below $60^{\circ}C$ regardless changing frequency. Further, above 6 kHz, the dielectric constant was set down even if temperature was above $100^{\circ}C$. Therefore, for the measurement of used oils, it was selected the frequency of 6 kHz, and the temperature of $80^{\circ}C$ preventing a certain ionic-conduction effects on the measured dielectric constant and the evaporation of a certain fluid mixed with engine oil. Specially, the effects of the mixing fluid like coolant, water and fuel on the fresh engine oil's dielectric constant were studied. It was found that the oil mixed with coolant showed the highest value, next water, and the lowest fuel. As results of the measurement of the used engine oil's dielectric constant, it was found that the possible changed rate of the used engine oil's dielectric constant based on the warning limit for engine oil in service was below 10% for diesel engine oil.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1998.11a
• /
• pp.187-190
• /
• 1998

In this paper a probe for the' measurement of dielectric properties of dielectric sheet materials is designed and implemented as a coaxial air line type. Using the broadband impedance method with this measurement probe the dielectric constant and loss tangent of the glass-epoxy and teflon are determined in the frequency range of 0.1 - l.O[GHz] with the temperature variation from $25[^{\circ}C]$ up to $65[^{\circ}C]$. A measured relative dielectric constant of the glass-epoxy is 4.42 and a loss tangents is 0.019 relatively, and the relative dielectric constants of teflon is 2.17 and a loss tangents is 0.002 relatively

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.10
• /
• pp.1115-1121
• /
• 2008

In this paper, dielectric slab loaded cylindrical cavity resonator measurement technique is presented to determine the dielectric constant of a dielectric material. The dielectric constant is measured by the resonant frequency deviation of empty and dielectric slab loaded cavity. Characteristic equations are derived by th exact field analysis. The measurement configurations are formed using HP8719A vector network analyzer and an experimental cylindrical metallic cavity with circular cross-section. The validity of the theory is confirmed by experiments and CST MWS 4.0(3D simulator). The results were in the whole satisfactory. The measured dielectric constant of teflon and bakelite are 2.03 and 4.44, respectively.

• Electrical & Electronic Materials
• /
• v.10 no.9
• /
• pp.960-967
• /
• 1997

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.21 no.10
• /
• pp.896-900
• /
• 2008

A measurement method of the dielectric constant of materials whose standard sample is not prepared easily is proposed. The unprepared sample of the material is placed in a cavity, and the resonant frequency is measured. A commercial software simulates the same sample and the cavity leading to find the correct dielectric constant. The measured samples include a ceramic, a forced glass, and a powdered enamel. The measured dielectric constant of a ceramic, a forced glass, and a powdered enamel are 11-j0.0033(${\epsilon}_{\gamma}=11,\;tan{\delta}=0.0003$), 4.15-j0.053(${\epsilon}_{\gamma}=4.15,\;tan{\delta}=0.0128$), and 3.9-j0.042(${\epsilon}_{\gamma}=3.9,\;tan{\delta}=0.0108$) respectively.

• Proceedings of the IEEK Conference
• /
• 2008.06a
• /
• pp.343-344
• /
• 2008

A measurement method of the dielectric constant of materials whose standard sample is not prepared easily is proposed. The unprepared sample of the material is placed in a cavity, and the resonant frequency is measured. A commercial software simulates the same sample and the cavity leading to find the correct dielectric constant. The measured samples include a ceramic, a forced glass, and a powdered enamel.