• ETRI Journal
• /
• v.40 no.1
• /
• pp.133-145
• /
• 2018

Robustness, payload, and imperceptibility of audio watermarking algorithms are contradictory design issues with high-level security of the watermark. In this study, the major issue in achieving high payload along with adequate robustness against challenging signal-processing attacks is addressed. Moreover, a security code has been strategically used for secure transmission of data, providing tamper detection at the receiver end. The high watermark payload in this work has been achieved by using the complementary features of third-level detailed coefficients of discrete wavelet transform where the human auditory system is not sensitive to alterations in the audio signal. To counter the watermark loss under challenging attacks at high payload, Daubechies wavelets that have an orthogonal property and provide smoother frequencies have been used, which can protect the data from loss under signal-processing attacks. Experimental results indicate that the proposed algorithm has demonstrated adequate robustness against signal processing attacks at 4,884.1 bps. Among the evaluators, 87% have rated the proposed algorithm to be remarkable in terms of transparency.

• Journal of Digital Convergence
• /
• v.12 no.8
• /
• pp.243-248
• /
• 2014

IPSec provides two services that are authentication header and Encapsulating Security Payload(ESP). In this research work, security issues on the Internet and the basic concept of IPSec are described. Security issues on the Internet are presented and proposed a possible solution for DDoS attack using IPSec. Therefore, this research will be able to contribute for building secure communication against DDoS attack.

• The Bulletin of The Korean Astronomical Society
• /
• v.37 no.2
• /
• pp.228.1-228.1
• /
• 2012

Digital waveform generation technology for SAR payload can be divided into DDS(Direct Digital Synthesizer) method and Memory Mapped(M/M) method. DDS is the single chip which consists of the Sine Table, NCO(Numerically Controlled Oscillator), DAC, and so on. DDS method is a very simple method because the circuit configuration is not complex but has a disadvantage that can not control phase and amplitude easily by using NCO. M/M method has the complexity of the circuit configuration because it requires the memories which stores the waveforms, the control circuits, and DAC. And this method should apply the high interface technology for being compatible with the wide bandwidth of the digital signal and has the difficulty for PCB design because the number of the signal lines should be increased according to the number of the data bits for DAC. Although it has several disadvantages, this method has the capability of pre-distortion function which can compensate the phase and amplitude characteristics of the system and also has an excellent advantage to make any arbitrary waveform, so this method is considered as an important technology with DDS method. This research describes the technological trends of the waveform generator for the SAR payload and analyzes the characteristics of the technology.

• Proceedings of the IEEK Conference
• /
• 2000.11a
• /
• pp.389-392
• /
• 2000

Electronics and Telecommunications Research Institute (ETRI) developed the Ka-band satellite communications payload. This system is able to provide a high data rate communication service with a bandwidth of 200 MHz, a wideband digital flunking services up to 155 Mbps and asymmetrical internet multimedia service. The system employs the common receive/transmit antenna and the 2-for-1 redundant scheme for the LNA-Downconverters. The different types of high power amplification, TWTA for one chain and SSPA for the other chain, are used lot the variety of experimental options. For the reliable test of the payload, EGSE was also developed. The parametric RF tests were carried out in order to measure the performance of Ka-band communication subsystem, in most case the results of RF performance test complied the payload requirement.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.04a
• /
• pp.112-117
• /
• 1997

This paper presents a GA(Genetic Algorithms)-Optical control strategy for the control of the swing motion and the transverse position of the overhead crane. The overhead crane system is defined uncertain due to unknown system parameters such as payload and trolly mass. To control the overhead crane. the GA-Optimal control scheme is suggested. which transfers a trolly to a desired place as fast as possible and minimizes the swing of the payload during the transfer. The genetic algorithms are applied to fine digital optimal feedback gains. A computer simulation demonstrate the performance of the proposed the GA-digital optimal controller for the overhead crane.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.12 no.4
• /
• pp.452-459
• /
• 2009

A 6-bit MMIC digital attenuator applicable to X-band TR module has been developed by using $0.5{\mu}m$GaAs pHEMT processes. The Switched-T attenuator scheme and the switched-path attenuator scheme were adopted to obtain low insertion loss and small phase variation, respectively. Resistors and transmission lines are optimized to achieve the digital attenuator with high attenuation accuracy and small phase variation. The digital attenuator has RMS error of 0.4dB, resolution of 0.5dB and dynamic range of 31.5dB. The measurement results show that in-out VSWRs are less than 1.5, phase variation is from -7 to +2 degrees and IIP3 is 36.5dBm.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.11 no.9
• /
• pp.855-860
• /
• 2016

This study describes the design and implementation of digital Payload power supply. We materialized the interface of the PLDIU and power supply of a satellite bus, and minimized the potential for the occurrence of such erroneous operation circuit ESD through the WCA of the space environment. We designed a reliable power supply through simulation for a TID according to the vibration generated during the launch and space radiation environment, and found no problem in the function and performance through the test space environment after production.

• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.1013_1014
• /
• 2009

In this paper, the electrical interfaces used in between COMS satellite bus and Ka-band communication payload are analyzed to verify the robustness of data bus. The purpose of the serial data bus of satellite is to allow serial data transfer between one bus controller or source equipment to several user terminals or slave equipments. A serial data bus in COMS satellite is mainly used for Channel Amplifier and Digital Control Unit of Ka-band Payload.

• Electronics and Telecommunications Trends
• /
• v.37 no.3
• /
• pp.41-51
• /
• 2022

This article presents an overview of the key technologies in the communications payload of broadband LEO satellite communications systems. In recent years, new developments have been realized for LEO satellite communications. SpaceX's Starlink, a technology leader in this field, offers premium services with satellites carrying in-house developed communications payloads. OneWeb, Amazon, Telesat, and Boeing are also developing LEO satellite communications payloads. The communications payload consists of user link antennas, inter-satellite link communications equipment, feeder link antennas, and a digital processor. Highly sophisticated technologies of compact active phased array antennas for generating multiple hopping beams and light laser communication equipment for ultra-high-speed inter-satellite communication will be applied to next- generation payloads.

• 제어로봇시스템학회:학술대회논문집
• /
• 1988.10a
• /
• pp.6-11
• /
• 1988

Alight-weight robot arm carrying a payload is modelled as a cantilever beam with a tip mass subjected to a high speed rotation. Equations of Motion, for modal control, are represented as discrete state variable form. Digital optimal control law with observer is developed to suppress the arm vibration and control the position of the joint angle. The effects of the number of controlled modes, weighting factors of the performance index, reference rotation time, and sampling time on the control performance are analyzed by computer simulation and experiments.